DOWNLOAD Sony DCR-IP210 / DCR-IP210E / DCR-IP220 / DCR-IP220E (serv.man4) Service Manual ↓ Size: 1.39 MB | Pages: 76 in PDF or view online for FREE

6-6

For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.

When performing only the adjustments, the lens block and boards
need not be disassembled.

Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.

1)

Connect the equipment for adjustments according to Fig. 6-1-3.

Be careful not to touch the ST-076 board (Flash drive circuit).
Because there is a danger of electric shock when the ST-076 board
is handled by hand.

Perform  “Zoom Key Center adjustment” and “Flange back
Adjustment” under the condition that the zoom switch (RV4001
of the control switch block (SS-2980)) is surely connected.

As removing the control switch block (PW-2980)) means removing
the lithium 3V power supply (BT4101 on the control switch block
(PW-2980)), data such as date, time, user-set menus will be lost.
After completing adjustments, reset these data.
But the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the lithium 3V power
supply is removed. (Refer to “6-4. Service Mode” for the self-
diagnosis data and the data on history of use.)

Setting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE

button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (PW-2980) removed. After
completing adjustments, be sure to exit the “Forced Camera
Power ON Mode”.

Exiting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE

button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

1.5 m

Front of the lens

Pattern box

Fig. 6-1-2.

6-7

Fig. 6-1-3.

 S video

Video (yellow)

Audio left (white)

Color monitor

Vector scope

Terminated at 75 

Ω

.

Adjustment
remote commander

Lens block

CD-406 board

DC IN jack

A/V jack

LD-112 board

LANC jack

ST-076 board

FP-542 flexible

EVF block

JK-234
board

FP-538
flexible

Mechanism deck

FP-539 flexible

CPC jig for LCD panel
(J-6082-529-A)

Cassette lid

Must be connected.

Must be connected 
when adjusting the
LCD system.

Need not 
be connected.

AN-025 
board

 (

2)

CN5801
Must be connected when 
manually focusing.

CN5800 Need not 
be connected.

Must be connected when 
manually focusing.

Need not 
be connected.

PD-166 board

CN803

CN801

CN802

CN804

Control switch block
(SS-2980)

Control switch block
(PW-2980)

CN4101

CN2021

CN2020

CN2006 

CN2011 Need not 
be connected

DI-087
board

DC-098 board

DI-087 board
CN2019

VC-308
 Board

CN463

CN453

CN458

CN451

CN457

CN462

CN461

CN456

CN455

CN001

CN452(CPC)

  TP4201
(TEST POINT
 for
 discharging
 the flash 
 capacitor)
 Caution!
 High voltage

LND421
(GND for 
discharging 
the flash  
capacitor)

AC power adaptor
(8.4Vdc)
AC-L20 or AC-VF50 (

1)

*

1: When using AC-VF50, a DC connection code (DK-225) is separately necessary.

*

2: DCR-IP220/IP220E only

Must be connected.

Must be 
connected.

PK-067 board
CN5001
Need not be 
connected.

Must be connected when checking the 
steady shot system or when adjusting 
the EVF system.

Audio Right (Red)

Need not be connected.

CN1000

CN4201

6-8

Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.

1.

POWER (PW-2980 block) ..................................... CAMERA

2.

FOCUS (FP-539 flexible) ..................................... MANUAL

3.

NIGHT SHOT (FP-538 flexible) ..................................... OFF

4.

BACK LIGHT (FP-524 flexible) ..................................... OFF

5.

FUNCTION settings (Touch panel)

EXPOSURE ................................................................ OFF
MANUAL SET of the MENU settings

PROGRAM AE ................................................ AUTO
PICTURE EFFECT .............................................. OFF
WHITE BALANCE .......................................... AUTO
AUTO SHUTTER ................................................ OFF

CAMERA SET of the MENU settings

DIGITAL ZOOM .................................................. OFF
16:9 WIDE ............................................................ OFF
STEADY SHOT ................................................... OFF

SETUP MENU of the MENU settings

DEMO MODE ...................................................... OFF

DIGITAL EFFECT ..................................................... OFF

Basically carry out adjustments in the order given.

Fig. 6-1-4.

1)

Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)

2)

Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)

3)

Flange back adjustment chart
Make the chart shown in Fig. 6-1-5. using A0 size (1189mm 

×

841mm) black and white vellum paper.

Fig. 6-1-5.

Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.

Fig. a

(Video output terminal

output waveform)

Fig. b (TV monitor picture)

Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.

6-9

A dark room is required to provide accurate flash and AF laser
adjustments.
If it is not available, prepare the flash adjustment box as given below;

woody board A (2 sheets)

400 mm

woody board B (2 sheets)

370 mm

woody board C (1 sheet)

700 mm

513 mm

513 mm

700 mm

700 mm

730 mm

1) Provide woody board A, B and C of 15 mm thickness.
2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side

of woody board A, B and C are internal. (Fig. 6-1-7.)

Fig. 6-1-6.

Fig. 6-1-7.