Sony DCR-IP210 / DCR-IP210E / DCR-IP220 / DCR-IP220E (serv.man4) Service Manual ▷ View online
6-2
DCR-IP210/IP210E/IP220/IP220E
Lens de
vice
Mechanism deck
Note1
LCD block
LCD901 (LCD panel (LCD))
LCD block
ND901 (fluorescent tube (LCD))
LCD block
T
ouch panel
EVFblock
LCD902 (LCD panel (EVF))
Mechanism block
M901 (Drum assy) Note1
Mechanism block
M902 (Capstan motor)
Mechanism block
Mechanism chassis assy
Control switch block (SS-2980)
Flash unit (FL-2980)
CD-406 board
IC1000 (CCD imager)
CD-406 board
IC1001 (S/H)
CD-406 board
IC1100,
X1100 (T
iming gener
ator)
DI-087 board
IC2201 (RGB dri
v
er (EVF))
DI-087 board
IC2202 (T
iming g
ener
ator (EVF))
FP-541 board
D5104 (Laser unit)
PD-166 board
IC801 (RGB dr
iv
er (LCD))
PD-166 board
IC802 (T
iming gener
ator (LCD))
VC-308 board
IC402 (A/D con
v.
)
VC-308 board
IC1901 (EVR)
VC-308 board
IC301 (Base band process)
VC-308 board
IC801 (REC/PB
AMP)
VC-308 board
IC2401 (VIDEO I/O)
VF-155 board
SE3001,3002 (PITCH,Y
A
W
sensor)
VF-155 board
D3601, 3602 (Backlight LED (EVF))
Replaced parts
Block replacement
Parts replacement
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z z
z z
z
z
z
z
z
z
z
z
z z
z
z
z z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
1-1. Adjusting items when replacing main parts and boards.
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by
z
in the following table.
Note1:
When replacing the drum assy. or the mechanism deck, reset the data of page: 7, address: A7 to A9 to “00”. (Refer to “Record of Use check” of
“6-4. SERVICE MODE”)
“6-4. SERVICE MODE”)
Adjustment
Section
Initialization of
4, 8, 9, A, B, C, D,
E, F, 1B,1E, 1F
page
Camera
Color EVF
LCD
Mechanism
System control
Servo, RF
Video
Adjustment
Initialization of A, D page data
Initialization of B, 1B page data
Initialization of E, F, 1E ,1F page data
Initialization of 4, 8, 9, C page data
67.5MHz/54MHz origin oscillation adj.
Zoom key center adj.
HALL adj.
CCD output 2ch matching adj.
MR adj.
Flange back adj.
MAX GAIN adj.
Color reproduction adj.
AWB & LV standard data input
Auto white balance adj.
Mechanical shutter adj
Strobe light level adjustment
Strobe white balance adjustment & check
AF laser output adj.
Steady shot check
Back light adj.
Bright adj.
Contrast adj.
White balance adj.
VCO check.
VCO adj.
Bright adj.
Black limit adj.
PSIG gray adj.
Contrast adj.
Center level adj.
V-COM adj.
White balance adj.
Tape path adj.
Touch panel adj.
Serial No. input
CAP FG duty adj.
Treel FG duty adj.
Read clock f
0
adj.
Switching position adj.
XREC ACT adj.
Timing ATF center value adj.
AGC adj.
Pch/Mch AEQ & LMS adj.
Chroma BPF f
0
adj.
S VIDEO OUT Y level adj.
S VIDEO OUT Chroma level adj.
COVER
COVER
Table. 6-1-1(1).
6-3
DCR-IP210/IP210E/IP220/IP220E
Board
EEPROM
replacement
replacement
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
BT
-012 boar
d
(COMPLETE )
Note3
CD-406 board
(COMPLETE )
DI-087 board
(COMPLETE )
LD-112 board
(COMPLETE)
PD-166 board
(COMPLETE )
VC-308 board
(COMPLETE )
Note4
VF-155 board
(COMPLETE )
VC-308 board
IC900 (EEPR
OM)
VC-308 board
IC1500 (EEPR
OM)
VC-308 board
IC1903 (EEPR
OM)
Supporting
• Adjusting items when replacing a board or EEPROM
When replacing a board or FFPROM, adjust the items indicated by
z
in the following table.
Note2:
When the repair is finished, confirm the
following items.
following items.
1.
Shoot the all black subject (Attach the
lens cap and shoot), and confirm that a
vertical line is not displayed in the center
of the screen, and that there is no
difference in left-right brightness level of
the screen.
lens cap and shoot), and confirm that a
vertical line is not displayed in the center
of the screen, and that there is no
difference in left-right brightness level of
the screen.
2.
Shoot a subject of low light, and confirm
that a vertical line is not displayed in the
center of the screen, and that there is no
difference in left-right brightness level of
the screen.
that a vertical line is not displayed in the
center of the screen, and that there is no
difference in left-right brightness level of
the screen.
3.
Shoot a subject of normal light, and
confirm that a vertical line is not
displayed in the center of the screen, and
that there is no difference in left-right
brightness level of the screen.
When the above symptom occurs,
perform the whole process of “CCD
Output 2ch Matching Adjustment”.
confirm that a vertical line is not
displayed in the center of the screen, and
that there is no difference in left-right
brightness level of the screen.
When the above symptom occurs,
perform the whole process of “CCD
Output 2ch Matching Adjustment”.
Note3:
DCR-IP220/IP220E only.
When the BT-012 board is replaced, perform
“Initialization of Bluetooth Unit”.
(Refer to “1-2-2. INITIALIZATION OF B, 1B
PAGE DATA”.)
Then perform following procedure and check
that the “Self Information” is displayed
correctly.
1)
“Initialization of Bluetooth Unit”.
(Refer to “1-2-2. INITIALIZATION OF B, 1B
PAGE DATA”.)
Then perform following procedure and check
that the “Self Information” is displayed
correctly.
1)
Set the POWER switch to MEMORY.
2)
Select “NETWORK” on the LCD
screen, then execute it.
screen, then execute it.
3)
Select “Setup” of the network menu, then
execute it.
execute it.
4)
Select “Bluetooth Setup”, then execute it.
5)
Select “Info.”, then execute it.
6)
Check that the following information is
displayed.
displayed.
Name
SONY DCR-IP220
Address
08:00:46:XX:XX:XX
Note4:
When replacing the VC-308 board, before
and after replacing, perform “Writing the
Network Default Setting Value” and
initialize the personal network
information (Mail address, bookmark
etc.). (DCR-IP220/IP220E)
(Refer to “1-2-2. INITIALIZATION OF
B, 1B PAGE DATA”.)
and after replacing, perform “Writing the
Network Default Setting Value” and
initialize the personal network
information (Mail address, bookmark
etc.). (DCR-IP220/IP220E)
(Refer to “1-2-2. INITIALIZATION OF
B, 1B PAGE DATA”.)
Adjustment
Section
Initialization of
4, 8, 9, A, B, C, D,
E, F, 1B,1E, 1F
page
Camera
Color EVF
LCD
Mechanism
System control
Servo, RF
Video
Adjustment
Initialization of A, D page data
Initialization of B, 1B page data
Initialization of E, F, 1E ,1F page data
Initialization of 4, 8, 9, C page data
67.5MHz/54MHz origin oscillation adj.
Zoom key center adj.
HALL adj.
CCD output 2ch matching adj.
MR adj.
Flange back adj.
MAX GAIN adj.
Color reproduction adj.
AWB & LV standard data input
Auto white balance adj.
Mechanical shutter adj
Strobe light level adjustment
Strobe white balance adjustment & check
AF laser output adj.
Steady shot check
Back light adj.
Bright adj.
Contrast adj.
White balance adj.
VCO check.
VCO adj.
Bright adj.
Black limit adj.
PSIG gray adj.
Contrast adj.
Center level adj.
V-COM adj.
White balance adj.
Tape path adj.
Touch panel adj.
Serial No. input
CAP FG duty adj.
Treel FG duty adj.
Read clock f
0
adj.
Switching position adj.
XREC ACT adj.
Timing ATF center value adj.
AGC adj.
Pch/Mch AEQ & LMS adj.
Chroma BPF f
0
adj.
S VIDEO OUT Y level adj.
S VIDEO OUT Chroma level adj.
Table. 6-1-1(2).
6-4
DCR-IP210/IP210E/IP220/IP220E
6-1. CAMERA SECTION ADJUSTMENT
1-1.
PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)
1-1-1.
List of Service Tools
• Oscilloscope
• Color monitor
• Vectorscope
• Regulated power supply
• Digital voltmeter
Note1:
If the micro processor IC in the adjustment remote commander is
not the new micro processor (UPD7503G-C56-12), the pages
cannot be switched. In this case, replace with the new micro
processor (8-759-148-35).
not the new micro processor (UPD7503G-C56-12), the pages
cannot be switched. In this case, replace with the new micro
processor (8-759-148-35).
Ref. No.
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
Name
Filter for color temperature correction (C14)
ND filter 1.0
ND filter 0.4
ND filter 0.1
Pattern box PTB-450
Color chart for pattern box
Adjustment remote commander
(RM-95 upgraded) (Note1)
Siemens star chart
Clear chart for pattern box
Mini pattern box
Camera table
CPC-jig for LCD panel
Background paper
Parts Code
J-6080-058-A
J-6080-808-A
J-6080-806-A
J-6080-807-A
J-6082-200-A
J-6020-250-A
J-6082-053-B
J-6080-875-A
J-6080-621-A
J-6082-353-B
J-6082-384-A
J-6082-529-A
J-2501-130-A
Usage
Auto white balance adjustment/check
White balance adjustment/check
White balance check
For checking the flange back
For adjusting the flange back
For adjusting the flange back
For adjusting the LCD system
For adjusting the flash unit
COVER
COVER
6-5
DCR-IP210/IP210E/IP220/IP220E
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
Fig. 6-1-1.
Click on the first or last page to see other DCR-IP210 / DCR-IP210E / DCR-IP220 / DCR-IP220E (serv.man4) service manuals if exist.