DOWNLOAD Sony DCR-IP210 / DCR-IP210E / DCR-IP220 / DCR-IP220E (serv.man4) Service Manual ↓ Size: 1.39 MB | Pages: 76 in PDF or view online for FREE

6-22

Before perform the camera system adjustments (except for
“67.5MHz/54MHz Origin Oscillation Adjustment”), check that the
specified values of “VIDEO SYSTEM ADJUSTMENTS” are
satisfied.
And check that the data of page: 0, address: 10 is “00”. If not, set
data: 00 to this address.

NTSC model: DCR- IP210/IP220
PAL model: DCR- IP210E/IP220E

Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color will
become inconsistent.

Subject

Not required

Measurement Point

Pin rf of IC1100 (FB1106)

Measuring Instrument

Frequency counter

Adjustment Page

F

Adjustment Address

10

Specified Value

f=33750000 ± 170Hz (NTSC)
f=27000000 ± 135Hz (PAL)

The data of page: 0, address: 10 must be “00”.

1

0

01

01

Set the data.

2

F

10

Change the data and set the
frequency (f) to the specified
value.

3

F

10

Press PAUSE button.

4

0

01

00

Set the data.

Fig. 6-1-8.

Set the A/D value center of the microprocessor to the center voltage
of the zoom key.
If deviated, the zoom lens operates of itself, even if the zoom key is
the center position.

Subject

Not required

Measuring Instrument

Adjusting remote commander

Adjustment Page

F

Adjustment Address

11

Perform this adjustment under the condition that the zoom switch
(RV4001 of the control switch block (SS-2980)) is surely
connected.

Don’t touch the zoom switch during adjustment.

The data of page: 0, address: 10 must be “00”.

1

0

01

01

Set the data.

2

6

01

13

Set the data, and press PAUSE
button. (Note4)

3

6

01

00

Set the data, and press PAUSE
button.

4

0

01

00

Set the data.

The adjustment data will be automatically input to page: F, address:
11.

IC1100

CD-406 board

FB1106

6-23

For detecting the position of the lens iris and ND filter, adjust AMP
gain and offset.

Subject

Not required

Measurement Point

Display data of page 1 (Note1)

Measuring Instrument

Adjustment remote commander

Adjustment Page

F

Adjustment Address

13 to 18

Specified Value 1

D6 to DA

Specified Value 2

26 to 2A

Specified Value 3

D6 to DA

Specified Value 4

26 to 2A

Displayed data of page 1 of the adjustment remote commander.

1 : XX : XX

IRIS display data
ND display data

The data of page: 0, address: 10 must be “00”.

POWER .................................................................. CAMERA

1

0

01

01

Set the data.

2

6

01

6D

Set the data, and press PAUSE
button.

3

6

02

Check that the data changes to
“01”. (Note3)

4

6

01

00

Set the data, and press PAUSE
button.

The adjustment data will be automatically input to page: F, address:
13 to 18.

1

0

03

03

Set the data.

2

6

01

01

Set the data, and press PAUSE button.

3

6

01

03

Set the data, and press PAUSE button.

4

1

Check that the IRIS display data
(Note1) satisfies the specified
value 1.

5

6

01

01

Set the data, and press PAUSE button.

6

1

Check that the IRIS display data
(Note1) satisfies the specified
value.2.

7

6

01

6B

Set the data, and press PAUSE button.

8

6

01

69

Set the data, and press PAUSE button.

9

1

Check that the ND display data
(Note1) satisfies the specified
value 3.

10

6

01

6B

Set the data, and press PAUSE button.

11

1

Check that the ND display data
(Note1) satisfies the specified
value 4.

1

6

01

00

Set the data, and press PAUSE
button.

2

0

03

00

Set the data.

3

0

01

00

Set the data.

Correct the dispersion of the black level between the left-right
channels of the CCD imager.

Subject

Arbitrary

Adjustment Page

F

Adjustment Address

24 to 27

This adjustment should be carried out upon completion of the
following adjustments.

“HALL Adjustment”

If this adjustment has been performed, the following adjustments
need to be performed again.

“CCD Output 2ch Matching Adjustment (2)”,  “Flange Back
Adjustment”, “Color Reproduction Adjustment”

The data of page: 0, address: 10 must be “00”.

Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.

Switch setting:
1)

POWER .................................................................. CAMERA

2)

NIGHT SHOT .................................................................. OFF

1

0

01

01

Set the data.

2

6

01

F3

Set the data, and press PAUSE
button.

3

6

02

Check that the data changes to
“01”. (Note4)

The adjustment data will be automatically input to page: F, address:
24 to 27.

1

6

01

00

Set the data, and press PAUSE
button.

2

Perform “CCD Output 2ch
Matching Adjustment (2)”.

6-24

Correct the dispersion between the left-right channels of the CCD
imager.

Subject

Clear chart (All white) (Note1)

Adjustment Page

F

Adjustment Address

29 to 2D

Shoot the clear chart with the zoom TELE end.

This adjustment should be carried out upon completion of the
following adjustments.

CCD Output 2ch Matching adjustment (1)

The data of page: 0, address: 10 must be “00”.

Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.

Switch setting:
1)

POWER .................................................................. CAMERA

2)

NIGHT SHOT .................................................................. OFF

3)

ZOOM .................................................................... TELE end

1

0

01

01

Set the data.

2

6

2C

01

Set the data.

3

6

40

01

Set the data.

4

6

01

F5

Set the data, and press PAUSE
button.

5

6

02

Check that the data changes to
“01” in about 50 seconds after
pressing PAUSE button.

The adjustment data will be automatically input to page: F, address:
29 to 2D

1

6

01

00

Set the data, and press PAUSE
button.

2

6

2C

00

Set the data.

3

6

40

00

Set the data.

4

0

01

00

Set the data.

The MR (Magnet resistor) adjustment of the inner focus lens is
carried out automatically. In whichever case, the focus will be
deviated during auto focusing/manual focusing.

Subject

Not required

Measurement Point

Adjustment remote commander

Measuring Instrument

Adjustment Page

F

Adjustment Address

58, 5A to 65

Specified Value1

40 to C0

Specified Value2

03 to 70

Specified Value3

90 to FD

Make the lens horizontal and perform this adjustment.

Perform this adjustment before “Flange Back Adjustment”.

The data of page: 0, address: 10 must be “00”.

Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.

1

0

01

01

Set the data.

2

6

01

BD

Set the data, and press PAUSE button.

3

6

02

Check that the data changes to
“01”. (Note5)

4

F

5A

Check that the data satisfies the
specified value 1.

5

F

5B

Check that the data satisfies the
specified value 1.

6

F

5C

Check that the data satisfies the
specified value 1.

7

F

5D

Check that the data satisfies the
specified value 1.

8

F

5E

Check that the data satisfies the
specified value 2.

9

F

5F

Check that the data satisfies the
specified value 3.

10

F

60

Check that the data satisfies the
specified value 2.

11

F

61

Check that the data satisfies the
specified value 3.

12

F

62

Check that the data satisfies the
specified value 2.

13

F

63

Check that the data satisfies the
specified value 3.

14

F

64

Check that the data satisfies the
specified value 2.

15

F

65

Check that the data satisfies the
specified value 3.

The adjustment data will be automatically input to page: F, address:
58, 5A to 65.

1

6

01

00

Set the data, and press PAUSE button.

2

0

01

00

Set the data.

3

Turn off the power and turn on
again

6-25

The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.

Subject

Siemens star chart with ND filter for
the minipattern box (Note1)

Measurement Point

Adjustment remote commander

Measuring Instrument

Adjustment Page

F

Adjustment Address

11, 48 to 58

Specified Value

Data of page: F, address: 57 is “00” to “09”.

Dark Siemens star chart.

Perform this adjustment under the condition that the zoom switch
(RV4001 of the control switch block (SS-2980)) is surely
connected.

This adjustment should be carried out upon completion of the
following adjustments.

“HALL Adjustment”, “MR Adjustment”

Make the lens horizontal and perform this adjustment.

The data of page: 0, address: 10 must be “00”.

Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.

Switch setting:
1)

POWER .................................................................. CAMERA

2)

NIGHT SHOT .................................................................. OFF

3)

COLOR SLOW SHUTTER ............................................. OFF

Preparations:
1)

The minipattern box is installed as shown in the following
figure.

The attachment lenses are not used.

2)

Install the minipattern box so that the distance between it and
the front of the lens of the camcorder is less than 3cm. (Remove
the lens hood.)

3)

Make the height of the minipattern box and the camcorder equal.

4)

Check that the output voltage of the regulated power supply is
the specified voltage.

5)

Check that at both the zoom lens TELE end and WIDE end,
the center of the Siemens star chart and center of the exposure
screen coincide.

Specified voltage: The specified voltage varies according to the minipattern

box, so adjust the power supply output voltage to the
specified voltage written on the sheet which is supplied
with the minipattern box.

Fig. 6-1-9.

1

0

01

01

Set the data.

2

6

01

13

Set the data, and press PAUSE
button. (Note7)

3

6

01

27

Set the data, and press PAUSE
button.

4

6

02

Check that the data changes to
“01”. (Note8)

5

F

57

Check the data is “00” to “09”.

Don’t touch the zoom switch, If you touch the zoom switch, the
zoom center adjustment data will be rewritten in the value that
isn’t correct.

The adjustment data will be automatically input to page: F, address
11, 48 to 58.

1

6

01

00

Set the data, and press PAUSE
button.

2

6

01

25

Set the data, and press PAUSE
button.

3

6

01

00

Set the data, and press PAUSE
button.

4

0

01

00

Set the data.

5

Perform “Flange Back Check”.

±