Sony DCR-HC21 (serv.man2) Service Manual ▷ View online
6-26
DCR-HC21
5.
18 Page table
Note 1:
If reading/writing data on pages 18, set data: 01 to page:
0, address: 10, and then select pages: 8. By this data set-
ting, the pages 18 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
0, address: 10, and then select pages: 8. By this data set-
ting, the pages 18 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
00
Fixed data-1 (Initialized data)
01
Fixed data-2
02 to FF
Fixed data-1 (Initialized data)
Address
Initial value
Remark
NTSC PAL
E0 to E4
Fixed data-1 (Initialized data)
E5
00
00
E6
00
00
Node unique ID No. Inputs
E7
00
00
E8 to F3
Fixed data-1 (Initialized data)
F4
00
00
Emergency memory address
F5
00
00
(Mechanism section)
F6
00
00
F7
00
00
F8
00
00
F9
00
00
FA
00
00
FB
00
00
FC
00
00
FD
00
00
FE
00
00
FF
00
00
C Page table
6-27
DCR-HC21
6.
1C Page table
Note 1:
If reading/writing data on pages 1C, set data: 01 to page:
0, address: 10, and then select pages: C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
0, address: 10, and then select pages: C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to B2
Fixed data-1 (Initialized data)
B3
00
00
SD error rate check (LP)
B4
00
00
B5
00
00
B6
00
00
B7
00
00
B8
80
80
B9
00
00
BA
00
00
BB
00
00
BC
00
00
BD
00
00
BE
00
00
BF
00
00
C0
00
00
C1
00
00
C2
00
00
C3
80
80
C4
00
00
C5
00
00
C6
00
00
C7
00
00
C8
00
00
C9 to E5
Fixed data-1 (Initialized data)
E6
Fixed data-2
E7
Fixed data-1 (Initialized data)
E8
00
00
When IC5301 is Type A.
(This data vary according to the
type of the IC5301 of VC-37
board.) (Note 3)
1E
1E
When IC5301 is Type B.
(This data vary according to the
type of the IC5301 of VC-377
board.) (Note 3)
E9
Fixed data-1 (Initialized data)
EA
EB
Fixed data-2
EC to EE
Fixed data-1 (Initialized data)
Address
Initial value
Remark
NTSC PAL
EF
F0
Fixed data-2
F1 to F7
Fixed data-1 (Initialized data)
F8
00
00
When IC5301 is Type A.
(This data vary according to the
type of the IC5301 of VC-377
board.) (Note 3)
60
60
When IC5301 is Type B.
(This data vary according to the
type of the IC5301 of VC-377
board.) (Note 3)
F9 to FF
Fixed data-1 (Initialized data)
Note 3:
By checking the data of page: 6, address: FF, the type of
IC5301 of VC-377 board can be discriminated.
IC5301 of VC-377 board can be discriminated.
Order Page Address Data
Procedure
1
0
10
00
2
6
FF
Check the data.
01: Type A
02 or more: Type B
01: Type A
02 or more: Type B
6-28
DCR-HC21
1-3-3.
Initialization of E, F, 19, 1E, 1F Page Data
1.
Initializing of E, F, 19, 1E, 1F Page Data
Note 1:
If “Initialization of Pages E, F, 19, 1E, 1F” is executed,
all data on pages E, F, 19, 1E, 1F are initialized. (Only an
individual page cannot be initialized)
all data on pages E, F, 19, 1E, 1F are initialized. (Only an
individual page cannot be initialized)
Note 2:
If the E, F, 19, 1E, 1F page data has been initialized, the
following adjustments need to be performed again.
1) Modification of E, F, 19, 1E, 1F page data
2) Camera system adjustment (if all areas were initial-
following adjustments need to be performed again.
1) Modification of E, F, 19, 1E, 1F page data
2) Camera system adjustment (if all areas were initial-
ized)
Note 3:
NTSC model: DCR-HC32/HC33
PAL model: DCR-HC32E/HC33E
PAL model: DCR-HC32E/HC33E
Adjustment Page
E
Adjustment Address
00 to FF
Adjustment Page
F
Adjustment Address
10 to FF
Adjustment Page
19
Adjustment Address
00 to 33
Adjustment Page
1E
Adjustment Address
00 to FF
Adjustment Page
1F
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data Procedure
1
0
01
01
2
0
10
00
Set the following data
3
6
01
2D: NTSC model
2F: PAL model
2F: PAL model
4
6
03
FF
Press PAUSE button.
5
6
02
Check the data changes to
“01”.
“01”.
6
6
01
00
Press PAUSE button.
7
Perform “Modification of E,
F, 19, 1E, 1F Page Data”
F, 19, 1E, 1F Page Data”
2.
Modification of E, F, 19, 1E, 1F Page Data
If the E, F, 19, 1E, 1F page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.
data of the “Fixed data-2” address shown in the following table by
manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages E, F, set data: 00 to page: 0,
address: 10, and then select pages E, F.
3) If modification of data on pages 19, 1E, 1F, set data: 01 to
page: 0, address: 10, and then select pages 9, E, F.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note:
If copy the data built in the different model, the
camcorder may not operate.
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
to write the data in the non-volatile memory.
6) If all areas were initialized, check that the data at the addresses
for adjustment are initial values (adjustment initial values)
listed in the table.
If different, change them to the adjustment initial values.
listed in the table.
If different, change them to the adjustment initial values.
Processing after Completing Modification E, F, 19, 1E, 1F
page data:
page data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE button.
4
Perform “36MHz Origin
Oscillation Adjustment” of
CAMERA SYSTEM
ADJUSTMENTS.
Oscillation Adjustment” of
CAMERA SYSTEM
ADJUSTMENTS.
6-29
DCR-HC21
3.
E Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to“1. Initializing the
E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to 07
Fixed data-1 (Initialized data)
08
09
Fixed data-2
0A to 11
Fixed data-1 (Initialized data)
12
Fixed data-2
13, 14
Fixed data-1 (Initialized data)
15
16
Fixed data-2
17
18 to 34
Fixed data-1 (Initialized data)
35
Fixed data-2
36 to 68
Fixed data-1 (Initialized data)
69
Fixed data-2
6A to 8D
Fixed data-1 (Initialized data)
8E
8F
Fixed data-2
90
Fixed data-1 (Initialized data)
91
Fixed data-2
92 to A3
Fixed data-1 (Initialized data)
A4
Fixed data-2
A5 to AA
Fixed data-1 (Initialized data)
AB
Fixed data-2
AC to AF
Fixed data-1 (Initialized data)
B0
Fixed data-2
B1
Fixed data-1 (Initialized data)
B2
B3
Fixed data-2
B4 to BD
Fixed data-1 (Initialized data)
BE
Fixed data-2
BF to E2
Fixed data-1 (Initialized data)
E3
E4
Fixed data-2
E5
E6 to FF
Fixed data-1 (Initialized data)
4.
F Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to“1. Initializing the
E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
10
80
80
36MHz origin osillation adj.
11
Fixed data-1 (Initialized data)
12
50
50
Hall adj.
13
50
50
14
89
89
15
00
00
16
17
17
17
00
00
18
19
19
19
9A
9A
MAX GAIN adj.
1A
36
36
LV standard data input
1B
00
00
1C
00
00
F No. standard data input
1D
00
00
1E
00
00
1F
00
00
20
00
00
21
00
00
22
00
00
23
00
00
24 to 29
Fixed data-1 (Initialized data)
2A
1B
1B
Auto white balance standard data
2B
00
00
input
2C
07
07
2D
00
00
2E
0E
0E
Auto white balance adj.
2F
00
00
30
0D
0D
31
00
00
32
Fixed data-1 (Initialized data)
33
22
22
Color reproduction adj.
34
Fixed data-1 (Initialized data)
35
27
24
Color reproduction adj.
36 to 39
Fixed data-1 (Initialized data)
3A
00
00
Color reproduction adj.
3B
F1
EF
3C, 3D
Fixed data-1 (Initialized data)
3E
2C
2C
Auto white balance adj.
3F
B0
B0
40
5F
5F
41
A0
A0
42, 43
Fixed data-1 (Initialized data)
Click on the first or last page to see other DCR-HC21 (serv.man2) service manuals if exist.