Sony DCR-HC21 (serv.man2) Service Manual ▷ View online
6-42
DCR-HC21
11. Color Reproduction Adjustment
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Measurement Point
Video terminal of A/V OUT jack or
A/V jack (75
A/V jack (75
Ω
terminated)
Measuring Instrument
Vectorscope
Adjustment Page
F
Adjustment Address
33, 35, 3A, 3B
Specified Value
All color luminance points should
settle within each color reproduction
frame.
settle within each color reproduction
frame.
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Perform “Flange Back Adjustment” and “F No. Standard
Data Input” before this adjustment.
Data Input” before this adjustment.
Note 3:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Note 4:
NTSC model: DCR-HC21/HC32/HC33
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/
HC32E/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
48
02
3
6
9D
Set the following data.
Non MS model
Non MS model
7E: NTSC model
86: PAL model
86: PAL model
MS model
80: NTSC model
89: PAL model
89: PAL model
4
6
01
3D
Press PAUSE button.
5
F
80
Set the following data, and
press PAUSE button.
press PAUSE button.
77: NTSC model
F7: PAL model
F7: PAL model
6
Adjust the GAIN and PHASE
of the vectorscope, and set to
the burst luminance point to
the burst position of color re-
production frame.
of the vectorscope, and set to
the burst luminance point to
the burst position of color re-
production frame.
7
F
Change the data and settle each
color luminance point in each
color reproduction frame.
(Note 5)
color luminance point in each
color reproduction frame.
(Note 5)
Note 5:
Be sure to press the PAUSE button of the adjusting re-
mote commander before changing the addresses. If not,
the new data will not be written to the memory.
mote commander before changing the addresses. If not,
the new data will not be written to the memory.
NTSC model
PAL model
33
35
35
3A
3B
3B
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
48
00
3
6
9D
00
4
0
01
00
Fig. 6-1-16
R-Y
Burst
B-Y
R
B
G
M
G
Y
E
C
Y
R-Y
B-Y
R
B
G
M
G
Y
E
C
Y
Burst
6-43
DCR-HC21
13. LV Standard Data Input
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust the normal coefficient of the light value.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Measurement Point
Displayed data of page: 1 (Note 4)
Measuring Instrument
Adjusting remote commander
Adjustment Page
F
Adjustment Address
1A, 1B
Specified Value
0FB0 to 1050
Note 1:
Perform “Flange Back Adjustment” and “F No. Stan-
dard Data Input” before this adjustment.
dard Data Input” before this adjustment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
Note 4:
The right four digits of the page: 1 displayed data of the
adjusting remote commander.
adjusting remote commander.
1:XX:XX
Displayed data
Note 5:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
0
01
01
3
6
48
02
4
6
01
0D
Press PAUSE button. (Note 6)
5
6
02
Check the data changes to
“01”.
“01”.
6
0
03
1E
7
1
Check that the displayed data
(Note 4) satisfied specified
value.
(Note 4) satisfied specified
value.
Note 6:
The adjustment data will be automatically input to page:
F, address: 1A and 1B.
F, address: 1A and 1B.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
48
00
3
0
03
00
4
0
01
00
12. Auto White Balance Standard Data Input
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust the white balance reference at 3200K.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Adjustment Page
F
Adjustment Address
2A to 2D
Note 1:
Perform “Color Reproduction Adjustment” before this
adjustment.
adjustment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
Note 4:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
0
01
01
3
Wait for 2 seconds.
4
6
48
02
5
6
01
11
Press PAUSE button.
6
6
01
0B
Press PAUSE button. (Note 5)
7
6
02
Check the data changes to
“01”.
“01”.
Note 5:
The adjustment data will be automatically input to page:
F, address: 2A to 2D.
F, address: 2A to 2D.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
48
00
3
0
01
00
6-44
DCR-HC21
14. Auto White Balance Adjustment
RadarW
RadarW
RadarW
Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility
will be poor.
If it is not correct, auto white balance and color reproducibility
will be poor.
Subject
Clear chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Filter
Filter C14 for color temperature
correction
correction
Adjustment Page
F
Adjustment Address
2E to 31, 3E to 41
Note 1:
Perform “Auto White Balance Standard Data Input” be-
fore this adjustment.
fore this adjustment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
Note 4:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Note 5:
NTSC model: DCR-HC21/HC32/HC33
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/
HC32E/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
Place the C14 filter on the
lens.
lens.
3
0
01
01
4
6
48
02
5
F
3E
Set the following data, and
press PAUSE button.
press PAUSE button.
29: NTSC model
2A: PAL model
2A: PAL model
6
F
3F
Set the following data, and
press PAUSE button.
press PAUSE button.
F8: NTSC model
B8: PAL model
B8: PAL model
7
F
40
5B
Press PAUSE button.
8
F
41
20
Press PAUSE button.
9
6
01
83
Press PAUSE button.
10
6
01
81
Press PAUSE button. (Note 6)
11
6
02
Check the data changes to
“01”.
“01”.
Note 6:
The adjustment data will be automatically input to page:
F, address: 2E to 31.
F, address: 2E to 31.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
48
00
3
0
01
00
4
Remove the C14 filter on the
lens.
lens.
6-45
DCR-HC21
Order Page Address Data
Procedure
3
6
48
02
INDOOR check
4
6
01
0F
Press PAUSE button.
5
Check that the center of the
white luminance point within
the circle shown Fig. 6-1-17
(A)
white luminance point within
the circle shown Fig. 6-1-17
(A)
6
6
01
00
Press PAUSE button.
OUTDOOR check
7
Place the C14 filter on the
lens.
lens.
8
6
01
3F
Press PAUSE button.
9
Check that the center of the
white luminance point within
the circle shown Fig. 6-1-17
(B)
white luminance point within
the circle shown Fig. 6-1-17
(B)
10
0
03
04
11
1
Check that the displayed data
(Note 3) satisfied the R ratio
specified value.
(Note 3) satisfied the R ratio
specified value.
12
0
03
05
13
1
Check that the displayed data
(Note 3) satisfied the B ratio
specified value.
(Note 3) satisfied the B ratio
specified value.
14
Remove the C14 filter
InOut data check
15
Place the ND filter 1.5 (1.0 +
0.4 + 0.1) on the lens.
0.4 + 0.1) on the lens.
16
6
01
00
Press PAUSE button.
17
0
03
06
18
1
Check that the displayed data
(Note 3) satisfied the InOut
data specified value.
(Note 3) satisfied the InOut
data specified value.
15. Auto White Balance Check
RadarW
RadarW
RadarW
RadarW
RadarW
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Filter
Filter C14 for color temperature
correction
ND filter 1.0, 0.4 and 0.1
correction
ND filter 1.0, 0.4 and 0.1
Measurement Point
Video terminal of
Displayed data of
A/V OUT jack or
page: 1 (Note 3)
A/V jack
(75
(75
Ω
terminated)
Measuring Instrument
Vectorscope
Adjusting remote
commander
commander
Specified Value
Fig. 6-1-17
NTSC model
(A) and (B)
R ratio:
29B8 to 2A38
B ratio:
5AE0 to 5B60
InOut data:
8000 to 8BC0
PAL model
R ratio:
R ratio:
2A78 to 2AF8
B ratio:
5AE0 to 5B60
InOut data:
8000 to 8BC0
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Perform “Auto White Balance Adjustment” before this
adjustment.
adjustment.
Note 3:
The right four digits of the page: 1 displayed data of the
adjusting remote commander.
adjusting remote commander.
1:XX:XX
Displayed data
Note 4:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Note 5:
NTSC model: DCR-HC21/HC32/HC33
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/
HC32E/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Fig. 6-1-17 (A)
R-Y
2 mm
B-Y
2 mm
R-Y
B-Y
0.5 mm
1 mm
3 mm
3 mm
Fig. 6-1-17 (B)
Checking method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
Check that the lens is not
covered with either filter.
covered with either filter.
Click on the first or last page to see other DCR-HC21 (serv.man2) service manuals if exist.