Sony DCR-HC21 (serv.man2) Service Manual ▷ View online
6-34
DCR-HC21
2. HALL Adjustment
RadarW
RadarW
RadarW
For detecting the position of lens iris, adjust the hall AMP gain
and offset.
and offset.
Subject
Not required
Measurement Point
Displayed data of page: 1 (Note 3)
Measuring Instrument
Adjusting remote commander
Adjustment Page
F
Adjustment Address
12 to 18
Specified value
Non MS model:
87 to 8B during IRIS OPEN
15 to 19 during IRIS CLOSE
MS model:
15 to 19 during IRIS OPEN
87 to 8B during IRIS CLOSE
87 to 8B during IRIS OPEN
15 to 19 during IRIS CLOSE
MS model:
15 to 19 during IRIS OPEN
87 to 8B during IRIS CLOSE
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
Note 3:
The right two digits of the page: 1 displayed data of the
adjusting remote commander.
adjusting remote commander.
1:00:XX
Displayed data
Note 4:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Switch setting:
1) POWER ............................. CAMERA mode (Non MS model)
1) POWER ............................. CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
D0
40
Non MS model only. (Note 4)
3
6
01
6D
Press PAUSE button. (Note 5)
4
6
02
Check the data changes to
“01”.
“01”.
Note 5:
The adjustment data will be automatically input to page:
F, address: 12 to 18.
F, address: 12 to 18.
Checking method:
Order Page Address Data
Procedure
1
0
03
03
2
6
01
01
Press PAUSE button.
3
1
Check that the displayed data
(Note 3) during IRIS OPEN
satisfied the specified value.
(Note 3) during IRIS OPEN
satisfied the specified value.
4
6
01
03
Press PAUSE button.
5
1
Check that the displayed data
(Note 3) during IRIS CLOSE
satisfied the specified value.
(Note 3) during IRIS CLOSE
satisfied the specified value.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
0
03
00
3
0
01
00
6-35
DCR-HC21
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
48
01
3
6
01
13
Press PAUSE button.
4
6
01
27
Press PAUSE button. (Note 7)
5
6
02
Check the data changes to
“01”.
“01”.
6
6
0C
Check the data is “00”.
Note 7:
The adjustment data will be automatically input to page:
F, address: 44 to 54 (Non MS model)/44 to 55 (MS
model).
F, address: 44 to 54 (Non MS model)/44 to 55 (MS
model).
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
01
25
Press PAUSE button.
3
6
01
00
Press PAUSE button.
4
6
48
00
5
0
01
00
6
Perform “Flange Back
Check”.
Check”.
3. Flange Back Adjustment
RadarW
RadarW
RadarW
RadarW
RadarW
(Using the minipattern box or flange back adjustment
jig)
jig)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated dur-
ing auto focusing/manual focusing.
automatically. In whichever case, the focus will be deviated dur-
ing auto focusing/manual focusing.
Subject
Siemens star chart with ND filter for
minipattern box (Note 1) or flange
back adjustment jig
minipattern box (Note 1) or flange
back adjustment jig
Measurement Point
Check operation on monitor TV
Measuring Instrument
Adjustment Page
F
Adjustment Address
Non MS model: 44 to 54
MS model: 44 to 55
MS model: 44 to 55
Specified value
Data of page: 6, address: 0C is “00”
Note 1:
Dark Siemens star chart.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
Note 4:
Perform the adjustment with the camcorder in horizon-
tal state.
tal state.
Note 5:
Perform “HALL Adjustment” before this adjustment.
Note 6:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
3) COLOR SLOW S (Menu setting) ............... OFF (MS model)
3) COLOR SLOW S (Menu setting) ............... OFF (MS model)
Preparations (Using the minipattern box)
1) The minipattern box is installed as shown in the following fig-
1) The minipattern box is installed as shown in the following fig-
ure.
Note 8:
The attachment lenses are not used.
2) Install the minipattern box so that the distance between it and
the front of lens of camcorder is less than 3 cm.
3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the
4) Check the output voltage of the regulated power supply is the
specified voltage
±
0.01 Vdc.
5) Check that the center of Siemens star chart meets the center of
shot image screen with the zoom lens at TELE end and WIDE
end respectively.
end respectively.
Specified voltage: The specified voltage varies according to the
minipattern box, so adjust the power supply
output voltage to the specified voltage written
on the sheet which is supplied with the
minipattern box.
output voltage to the specified voltage written
on the sheet which is supplied with the
minipattern box.
Fig. 6-1-9
PPreparation (Using the flange back adjustment jig)
(Luminance: about 300 lux)
1) Install the flange back adjustment jig so that the distance be-
(Luminance: about 300 lux)
1) Install the flange back adjustment jig so that the distance be-
tween it and the front of lens of camera is less than 3 cm.
2) Make the height of flange back adjustment jig and the camera
equal.
3) Check that the center of chart meets the center of shot image
screen with the zoom lens at TELE end and WIDE end respec-
tively.
tively.
Fig. 6-1-10
Minipattern box
Below 3 cm
Camcorder
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Need not connected
Regulated power supply
Output voltage : Specified voltage
±
0.01 Vdc
Output current : more than 3.5 A
Flange back adjustment jig
Below 3 cm
Camera
6-36
DCR-HC21
4. Flange Back Adjustment
(Using the flange back adjustment chart and
subject more than 500 m away)
subject more than 500 m away)
The inner focus lens flange back adjustment is carried out auto-
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
4-1. Flange Back Adjustment (1)
RadarW
RadarW
RadarW
Subject
Flange back adjustment chart
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
Measurement Point
Check operation on monitor TV
Measuring Instrument
Adjustment Page
F
Adjustment Address
Non MS model: 44 to 54
MS model: 44 to 55
MS model: 44 to 55
Specified value
Data of page: 6, address: 0C is “00”
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
Note 3:
Perform the adjustment with the camcorder in horizon-
tal state.
tal state.
Note 4:
Perform “HALL Adjustment” before this adjustment.
Note 5:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
3) COLOR SLOW S (Menu setting) ............... OFF (MS model)
3) COLOR SLOW S (Menu setting) ............... OFF (MS model)
Preparations before adjustments:
1) Place the Flange back adjustment chart 2.0 m from the front
1) Place the Flange back adjustment chart 2.0 m from the front
of the lens.
2) Check that the center of Flange back adjustment chart meets
the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.
end and WIDE end respectively.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
48
01
3
6
01
13
Press PAUSE button.
4
6
01
15
Press PAUSE button. (Note 6)
5
6
02
Check the data changes to
“01”.
“01”.
6
6
0C
Check the data is “00”.
Note 6:
The adjustment data will be automatically input to page:
F, address: 44 to 54 (Non MS model)/44 to 55 (MS
model).
F, address: 44 to 54 (Non MS model)/44 to 55 (MS
model).
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
01
25
Press PAUSE button.
3
6
01
00
Press PAUSE button.
4
6
48
00
5
0
01
00
6
Perform “Flange Back
Adjustment (2)”.
Adjustment (2)”.
6-37
DCR-HC21
4-2. Flange Back Adjustment (2)
RadarW
RadarW
RadarW
RadarW
RadarW
Perform this adjustment after performing “Flange Back Adjust-
ment (1)”.
ment (1)”.
Subject
Subject more than 500 m away
(Subject with clear contrast such as
buildings, etc.)
(Subject with clear contrast such as
buildings, etc.)
Measurement Point
Check operation on monitor TV
Measuring Instrument
Adjustment Page
F
Adjustment Address
Non MS model: 44 to 54
MS model: 44 to 55
MS model: 44 to 55
Specified value
Data of page: 6, address: 0C is “00”
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE button.
Note 3:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
3) COLOR SLOW S (Menu setting) ............... OFF (MS model)
3) COLOR SLOW S (Menu setting) ............... OFF (MS model)
Preparations before adjustments:
1) Set the zoom lens to the TELE end and expose a subject that is
1) Set the zoom lens to the TELE end and expose a subject that is
more than 500 m away.
(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the
screen)
(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the
screen)
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
48
01
3
6
01
13
Press PAUSE button.
4
Place ND filter on the lens so
that the optimum image is
obtain.
that the optimum image is
obtain.
5
6
01
29
Press PAUSE button. (Note 4)
6
6
02
Check the data changes to
“01”.
“01”.
7
6
0C
Check the data is “00”.
Note 4:
The adjustment data will be automatically input to page:
F, address: 44 to 54 (Non MS model)/44 to 55 (MS
model).
F, address: 44 to 54 (Non MS model)/44 to 55 (MS
model).
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
01
25
Press PAUSE button.
3
6
01
00
Press PAUSE button.
4
6
48
00
5
0
01
00
6
Perform “Flange Back
Check”.
Check”.
5. Flange Back Check
Subject
Siemens star
(2.0 m from the front of the lens)
(Luminance: approx. 200 lux)
(2.0 m from the front of the lens)
(Luminance: approx. 200 lux)
Measurement Point
Check operation on monitor TV
Measuring Instrument
Specified value
Focused at the TELE end and WIDE
end
end
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
Switch setting:
1) POWER ............................ CAMERA mode (Non MS model)
1) POWER ............................ CAMERA mode (Non MS model)
CAMERA-TAPE mode (MS model)
2) NIGHTSHOT PLUS ........................................................ OFF
Note 3:
When the auto focus is ON, the lens can be checked if it
is focused or not by observing the data on the page: 1 of
the adjusting remote commander.
is focused or not by observing the data on the page: 1 of
the adjusting remote commander.
1 : 00 : XX
Odd: Focused
Even: Unfocused
Even: Unfocused
Checking method:
Order Page Address Data
Procedure
1
Place the Siemens star 2.0 m
from the front of the lens.
from the front of the lens.
2
To open the IRIS, decrease
the luminous intensity to the
Siemens star up to a point be-
fore noise appear on the image.
the luminous intensity to the
Siemens star up to a point be-
fore noise appear on the image.
3
6
40
01
4
6
41
01
5
Shoot the Siemens star with
the zoom TELE end.
the zoom TELE end.
6
Turn on the auto focus.
7
0
03
0F
8
1
Check that the lens is
focused. (Note 3)
focused. (Note 3)
9
6
21
10
10
Shoot the Siemens star with
the zoom WIDE end.
the zoom WIDE end.
11
Observe the TV monitor and
check that the lens is
focused.
check that the lens is
focused.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
21
00
2
6
40
00
3
6
41
00
4
0
03
00
Click on the first or last page to see other DCR-HC21 (serv.man2) service manuals if exist.