Sony DCR-HC21 (serv.man2) Service Manual ▷ View online
6-10
DCR-HC21
4.
Preparing the Flash Adjustment Box
A dark room is required to provide an accurate flash adjustment.
If it is not available, prepare the flash adjustment box as given
below;
If it is not available, prepare the flash adjustment box as given
below;
1) Provide woody board A, B and C of 15 mm thickness.
2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper
side of woody board A, B and C are internal. (Fig. 6-1-7)
Fig. 6-1-6
Fig. 6-1-7
woody board A (2)
400 mm
woody board B (2)
370 mm
woody board C (1)
700 mm
513 mm
513 mm
700 mm
700 mm
730 mm
woody board A
woody board B
woody board B
woody board C
woody board A
6-11
DCR-HC21
2.
Modification of A, D Page Data
If the A, D page data has been initialized, change the data of
the“Fixed data-2” address shown in the following table by manual
input.
the“Fixed data-2” address shown in the following table by manual
input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note 1:
If copy the data built in the different model, the
camcorder may not operate.
camcorder may not operate.
3) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after completing modification A, D page data:
Order Page Address Data
Procedure
1
2
00
29
2
2
01
29
Press PAUSE button.
Note 2:
If the following symptoms occur after completing of
the“Modification A, D page data”, check that the data of
the “Fixed data-2” addresses of A, D page are same as
those of the same model of the same destination.
1) The power is shut off so that unit cannot operate.
the“Modification A, D page data”, check that the data of
the “Fixed data-2” addresses of A, D page are same as
those of the same model of the same destination.
1) The power is shut off so that unit cannot operate.
1-2-1.
Initialization of A, D Page Data
Note:
Check that the data of page: 0, address: 10 is “00”.
1.
Initializing of A, D Page Data
Note 1:
If “Initialization of Pages A, D” is executed, all data on
pages A, D are initialized.
pages A, D are initialized.
Note 2:
If the A, D page data has been initialized, the following
adjustments need to be performed again.
1) Modification of A, D page data
2) Touch panel adjustment
adjustments need to be performed again.
1) Modification of A, D page data
2) Touch panel adjustment
Note 3:
NTSC model: DCR-HC21/HC32/HC33
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/
HC32E/HC33E
Adjustment Page
A
Adjustment Address
10 to FF
Adjustment Page
D
Adjustment Address
10 to 7F
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
7
03
Set the following data.
01: NTSC model
81: PAL model
01: NTSC model
81: PAL model
4
7
00
Set the following data.
20: Initializing A page
22: Initializing D page
28: Initializing A and D pages
20: Initializing A page
22: Initializing D page
28: Initializing A and D pages
5
7
01
Set the following data, and
press PAUSE button.
20: Initializing A page
22: Initializing D page
28: Initializing A and D pages
press PAUSE button.
20: Initializing A page
22: Initializing D page
28: Initializing A and D pages
6
7
02
Check the data changes to
“01”.
“01”.
7
Perform “Modification of A,
D Page Data”
D Page Data”
1-2.
INITIALIZATION OF 8, A, C, D, E, F, 1C, 1F
PAGE DATA (Non MS model)
PAGE DATA (Non MS model)
Note 1:
If reading/writing data on pages 1C, 1F, set data: 01 to
page: 0, address: 10, and then select pages C, F. By this
data setting, the pages 1C, 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
page: 0, address: 10, and then select pages C, F. By this
data setting, the pages 1C, 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
6-12
DCR-HC21
3.
A Page Table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the A, D Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, D Page Data”)
the A, D Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, D Page Data”)
Address
Initial value
Remark
NTSC PAL
10 to 19
Fixed data-1 (Initialized data)
1A
1B
Fixed data-2
1C to 30
Fixed data-1 (Initialized data)
31
32
Fixed data-2
33 to 38
Fixed data-1 (Initialized data)
39
Fixed data-2
3A to 43
Fixed data-1 (Initialized data)
44
Fixed data-2
45 to 4A
Fixed data-1 (Initialized data)
4B
Fixed data-2
4C
Fixed data-1 (Initialized data)
4D
Fixed data-2
4E
Fixed data-1 (Initialized data)
4F
Fixed data-2
50 to 52
Fixed data-1 (Initialized data)
53
54
55
Fixed data-2
56 to 79
Fixed data-1 (Initialized data)
7A
7B
Fixed data-2
7C to 7F
Fixed data-1 (Initialized data)
80
81
Fixed data-2
82
CB
CC
Touch panel adj
83
20
1D
84
CF
C4
85
1C
28
86 to 8F
Fixed data-1 (Initialized data)
90
Fixed data-2
91 to F0
Fixed data-1 (Initialized data)
F1
F2
F3
Fixed data-2
F4 to FF
Fixed data-1 (Initialized data)
4.
D Page Table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the A, D Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, D Page Data”)
the A, D Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, D Page Data”)
Address
Initial value
Remark
NTSC PAL
10
00
00
Test mode
11
Fixed data-1 (Initialized data)
12
13
Fixed data-2
14 to 16
Fixed data-1 (Initialized data)
17
18
19
Fixed data-2
1A to 21
Fixed data-1 (Initialized data)
22
23
24
Fixed data-2
25
26
27 to 29
Fixed data-1 (Initialized data)
2A
2B
Fixed data-2
2C to 36
Fixed data-1 (Initialized data)
37
Fixed data-2
38, 39
Fixed data-1 (Initialized data)
3A
Fixed data-2
3B, 3C
Fixed data-1 (Initialized data)
3D
Fixed data-2
3E, 3F
Fixed data-1 (Initialized data)
40
Fixed data-2
41 to 54
Fixed data-1 (Initialized data)
55
56
Fixed data-2
57
58 to 6E
Fixed data-1 (Initialized data)
6F
Fixed data-2
70 to 7F
Fixed data-1 (Initialized data)
6-13
DCR-HC21
2.
Modification of 8, C, 1C Page Data
If the 8, C, 1C page data has been initialized, change the data of
the “Fixed data-2” address shown in the following table by manual
input.
the “Fixed data-2” address shown in the following table by manual
input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages 8, C, set data: 00 to page: 0,
address: 10, and then select pages 8, C.
3) If modification of data on pages 1C, set data: 01 to page: 0,
address: 10, and then select pages C. After the modification of
data finished, return the data on page: 0, address: 10 to “00”.
data finished, return the data on page: 0, address: 10 to “00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note:
If copy the data built in the different model, the
camcorder may not operate.
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after completing modification 8, C, 1C page data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE button.
1-2-2.
Initialization of 8, C, 1C Page Data
Note:
If reading/writing data on pages 1C, set data: 01 to page:
0, address: 10, and then select pages C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
0, address: 10, and then select pages C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
1.
Initializing of 8, C, 1C Page Data
Note 1:
If “Initialization of Pages 8, C, 1C” is executed, all data
on pages 8, C, 1C are initialized. (Only an individual
page cannot be initialized)
on pages 8, C, 1C are initialized. (Only an individual
page cannot be initialized)
Note 2:
If the 8, C, 1C page data has been initialized, the follow-
ing adjustments need to be performed again.
1) Modification of 8, C, 1C page data
2) Electronic viewfinder system adjustments
3) LCD system adjustments
4) Node unique ID No. input
5) Servo, RF system adjustments
6) Video system adjustments.
ing adjustments need to be performed again.
1) Modification of 8, C, 1C page data
2) Electronic viewfinder system adjustments
3) LCD system adjustments
4) Node unique ID No. input
5) Servo, RF system adjustments
6) Video system adjustments.
Adjustment Page
8
Adjustment Address
00 to FF
Adjustment Page
C
Adjustment Address
10 to FF
Adjustment Page
1C
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
3
81
Check that the data is “00”.
4
3
80
0C
Press PAUSE button.
5
3
80
Check the data changes to
“1C”.
“1C”.
6
Perform “Modification of 8,
C, 1C Page Data”
C, 1C Page Data”
Click on the first or last page to see other DCR-HC21 (serv.man2) service manuals if exist.