Sony DCR-HC1000 / DCR-HC1000E (serv.man4) Service Manual ▷ View online
6-6
DCR-HC1000/HC1000E
Fig. 6-1-3.
7
5
3
2
2
6
4
1
3
4
1
3
AC power
adaptor
adaptor
AC IN
Adjustment remote
commander (RM-95)
commander (RM-95)
LANC jack
For tape path adjustment
8
1
1
RF MON
2
SWP
3
GND
4
XSC EEP
5
EEP SCK
6
EEP SO
7
EEP SI
I/F unit for LANC control
(J-6082-521-A)
(J-6082-521-A)
CPC-15
(J-6082-564-A)
(J-6082-564-A)
*1
*1
[CONNECTION OF EQUIPMENT]
CN002
CN001
BATT
LANC
Not used
Not used
Not used.
Not used
*1: Don’t connect any cable
to these connectors.
DC-IN connector
CPC lid
6-7
DCR-HC1000/HC1000E
White
Black
841mm
1189mm
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1.
MODPOWER switch (PS8200 block) ........ CAMERA-TAPE
2.
FOCUS switch (FP-958 flexible) .......................... MANUAL
3.
BACK LIGHT switch (FP-958 flexible) .......................... OFF
4.
AUTO LOCK switch (FP-958 flexible) ............................ ON
5.
MENU settings (Touch panel)
CAMERA SET menu
AE SHIFT ................................................................... 0
ZEBRA .................................................................. OFF
DIGITAL ZOOM ................................................... OFF
ZEBRA .................................................................. OFF
DIGITAL ZOOM ................................................... OFF
16:9 WIDE ............................................................. OFF
STEADY SHOT ..................................................... OFF
STEADY SHOT ..................................................... OFF
PICT. APPLI. menu
DIGITAL EFECT .................................................. OFF
PICTURE EFECT .................................................. OFF
DEMO MODE ....................................................... OFF
PICTURE EFECT .................................................. OFF
DEMO MODE ....................................................... OFF
STANDARD SET menu
COLOR BAR ......................................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig.6-1-4.
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm
×
841mm) black and white vellum paper.
Fig. 6-1-5.
Note:
Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
the black and white paper joined together are not rough.
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
e
llo
w
Cy
an
Green
White
Magenta
Red
Blue
Y
e
llo
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame )
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
6-8
DCR-HC1000/HC1000E
4. Preparing the Flash Adjustment Box
A dark room is required to provide an accurate strobe adjustment.
If it is not available, prepare the flash adjustment box as given below;
If it is not available, prepare the flash adjustment box as given below;
1) Provide woody board A, B and C of 15 mm thickness.
woody board A (2 sheets)
400 mm
woody board B (2 sheets)
370 mm
woody board C (1 sheet)
700 mm
513 mm
513 mm
700 mm
700 mm
730 mm
2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side
of woody board A, B and C are internal. (Fig. 6-1-7.)
Fig. 6-1-6.
woody board A
woody board B
woody board B
woody board C
woody board A
Fig. 6-1-7.
6-9
DCR-HC1000/HC1000E
1-2.
INITIALIZATION OF 8, A, B, C, D, E, F, 18, 1A,
1B, 1C, 1E, 1F PAGE DATA
1B, 1C, 1E, 1F PAGE DATA
Note:
When reading or writing the 18, 1A, 1B, 1C, 1E or 1F page data,
select page: 0, address: 10, and set data: 01, then select 8, A, B, C, E
or F page. The 18, 1A, 1B, 1C 1E, or 1F page can be chosen by this
data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
select page: 0, address: 10, and set data: 01, then select 8, A, B, C, E
or F page. The 18, 1A, 1B, 1C 1E, or 1F page can be chosen by this
data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
1-2-1.
LOADING OF FLASH MEMORY PROGRAM
Read the program for the HI/DS controller (IC8401) from the
memory stick DUO, and write it to the flash memory (IC8503) of
the HI/DS controller.
memory stick DUO, and write it to the flash memory (IC8503) of
the HI/DS controller.
Note:
The data of page: 0, address: 10 must be “00”.
1. Preparation
1)
Write the VERMEER. BIN file (program file for the HI/DS
controller) to a memory stick Duo using a personal computer.
controller) to a memory stick Duo using a personal computer.
Note:
Contact our service headquarter of each area how to get the
VERMEER. BIN file.
VERMEER. BIN file.
2. Loader Writing Permission Mode Setting
Note:
This setting is unnecessary when no program is loaded to the flash
memory, or when “Loader Writing Permission Mode” is set already.
(Refer to “6. Check of Loader Writing Inhibit Mode”.)
memory, or when “Loader Writing Permission Mode” is set already.
(Refer to “6. Check of Loader Writing Inhibit Mode”.)
Setting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
7
01
2F
Set the data, and press PAUSE
button.
button.
3
7
02
FF
Set the data, and press PAUSE
button.
button.
4
7
04
00
Set the data, and press PAUSE
button.
button.
5
7
05
01
Set the data, and press PAUSE
button.
button.
6
7
06
FF
Set the data, and press PAUSE
button.
button.
7
7
00
01
Set the data, and press PAUSE
button.
button.
8
7
02
Check that the data is “01”.
3. Loading Method
1)
Remove the power supply of the camcorder.
2)
Inserts the memory stick Duo that memorizes the
VERMEER.BIN file to the memory stick slot.
VERMEER.BIN file to the memory stick slot.
3)
Connect the adjustment remote commander with the HOLD
switch set to the “ADJ” side.
switch set to the “ADJ” side.
4)
Connect the power supply to the camcorder.
5)
Check that the MS ACCESS LED is turned on for several
seconds. (The program is written in the flash memory in this
period.)
seconds. (The program is written in the flash memory in this
period.)
6)
Check that the MS ACCESS LED is turned off.
7)
Remove the memory stick D
UO
from the camcorder.
8)
Turn off the power and turn on again.
9)
Check that the camcorder is normal.
If normal, perform “4. Program Version Check” and “5. Loader
Writing Inhibit Mode Setting”.
If the MS ACCESS LED is blinked, repeat from step 1).
If normal, perform “4. Program Version Check” and “5. Loader
Writing Inhibit Mode Setting”.
If the MS ACCESS LED is blinked, repeat from step 1).
4. Program Version Check
Order Page Address Data
Procedure
1
5
FE
Read the data, and this data is
named D
named D
FE
.
2
5
FF
Read the data, and this data is
named D
named D
FF
.
Note:
D
FE
and D
FF
are the program version.
5. Loader Writing Inhibit Mode Setting
Setting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
7
01
2F
Set the data, and press PAUSE
button.
button.
3
7
02
FF
Set the data, and press PAUSE
button.
button.
4
7
04
00
Set the data, and press PAUSE
button.
button.
5
7
05
01
Set the data, and press PAUSE
button.
button.
6
7
06
20
Set the data, and press PAUSE
button.
button.
7
7
00
01
Set the data, and press PAUSE
button.
button.
8
7
02
Check that the data is “01”.
9
2
00
29
Set the data.
10
2
01
29
Set the data, and press PAUSE
button.
button.
6. Check of Loader Writing Inhibit Mode
Checking method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
7
01
1F
Set the data, and press PAUSE
button.
button.
3
7
02
FF
Set the data, and press PAUSE
button.
button.
4
7
03
00
Set the data, and press PAUSE
button.
button.
5
7
04
00
Set the data, and press PAUSE
button.
button.
6
7
05
01
Set the data, and press PAUSE
button.
button.
7
7
00
01
Set the data, and press PAUSE
button.
button.
8
7
02
Check that the data is “01”.
9
7
03
Check the data.
20: Loader writing inhibit mode
FF: Loader writing permission
20: Loader writing inhibit mode
FF: Loader writing permission
mode
10
0
01
00
Set the data.
Click on the first or last page to see other DCR-HC1000 / DCR-HC1000E (serv.man4) service manuals if exist.