Sony DCR-HC1000 / DCR-HC1000E (serv.man4) Service Manual ▷ View online
6-22
DCR-HC1000/HC1000E
3. MR Adjustment
The MR (Magnet resistor) adjustment of the inner focus lens is
carried out automatically. In whichever case, the focus will be
deviated during auto focusing/manual focusing.
carried out automatically. In whichever case, the focus will be
deviated during auto focusing/manual focusing.
Subject
Not required
Measurement Point
Adjustment remote commander
Measuring Instrument
Adjustment Page
F
Adjustment Address
70 to 7C
Specified Value1
40 to C0
Specified Value2
03 to 78
Specified Value3
88 to F8
Note1:
Make the lens horizontal and perform this adjustment.
Note2:
Perform this adjustment before “Flange Back Adjustment”.
Note3:
The data of page: 0, address: 10 must be “00”.
Note4:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1)
1)
POWER ....................................................... CAMERA-TAPE
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
01
BD
Set the data, and press PAUSE
button.
button.
3
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
4
F
71
Check that the data satisfies the
specified value 1.
specified value 1.
5
F
72
Check that the data satisfies the
specified value 1.
specified value 1.
6
F
73
Check that the data satisfies the
specified value 1.
specified value 1.
7
F
74
Check that the data satisfies the
specified value 1.
specified value 1.
8
F
75
Check that the data satisfies the
specified value 2.
specified value 2.
9
F
76
Check that the data satisfies the
specified value 3.
specified value 3.
10
F
77
Check that the data satisfies the
specified value 2.
specified value 2.
11
F
78
Check that the data satisfies the
specified value 3.
specified value 3.
12
F
79
Check that the data satisfies the
specified value 2.
specified value 2.
13
F
7A
Check that the data satisfies the
specified value 3.
specified value 3.
14
F
7B
Check that the data satisfies the
specified value 2.
specified value 2.
15
F
7C
Check that the data satisfies the
specified value 3.
specified value 3.
Note5:
The adjustment data will be automatically input to page: F, address:
70 to 7C.
70 to 7C.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
0
01
00
Set the data.
3
Turn off the power and turn on
again.
again.
6-23
DCR-HC1000/HC1000E
4. Flange Back Adjustment
(Using Minipattern Box or Flange Back Adjustment Jig)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
Subject
Flange back adjustment jig
Or minipattern box (Siemens star
chart with ND filter (Note1))
Or minipattern box (Siemens star
chart with ND filter (Note1))
Measurement Point
Adjustment remote commander
Measuring Instrument
Adjustment Page
F
Adjustment Address
60 to 70, A6
Specified Value
Data of page: F, address: 6F is “00” to
“0E”.
Data of page: F, address: A6 is “00” to
“3F” or “C1” to “FF”.
“0E”.
Data of page: F, address: A6 is “00” to
“3F” or “C1” to “FF”.
Note1:
Dark Siemens star chart.
Note2:
This adjustment should be carried out upon completion of the
following adjustments.
“HALL Adjustment”, “MR Adjustment”
following adjustments.
“HALL Adjustment”, “MR Adjustment”
Note3:
Make the lens horizontal and perform this adjustment.
Note4:
The data of page: 0, address: 10 must be “00”.
Note5:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1)
1)
POWER ....................................................... CAMERA-TAPE
Preparations for the minipattern box:
1)
1)
The minipattern box is installed as shown in the following
figure.
figure.
Note:
The attachment lenses are not used.
2)
Install the minipattern box so that the distance between it and
the front of the lens of the camcorder is less than 3cm.
the front of the lens of the camcorder is less than 3cm.
3)
Make the height of the minipattern box and the camcorder equal.
4)
Check that the output voltage of the regulated power supply is
the specified voltage.
the specified voltage.
5)
Check that at both the zoom TELE end and WIDE end, the
center of the Siemens star chart and center of the monitor TV
screen coincide.
center of the Siemens star chart and center of the monitor TV
screen coincide.
Specified voltage:
The specified voltage varies according to the minipattern box, so
adjust the power supply output voltage to the specified voltage
written on the sheet which is supplied with the minipattern box.
The specified voltage varies according to the minipattern box, so
adjust the power supply output voltage to the specified voltage
written on the sheet which is supplied with the minipattern box.
Preparations for the flange back adjustment jig:
1)
1)
Install the flange back adjustment jig so that the distance
between it and the front of the lens of the camcorder is less
than 3cm.
between it and the front of the lens of the camcorder is less
than 3cm.
2)
Adjust the illumination intensity to the chart of the flange back
adjustment jig. (350 ± 50 lux)
adjustment jig. (350 ± 50 lux)
3)
Check that at both the zoom TELE end and WIDE end, the
center of the chart and center of the monitor TV screen coincide.
center of the chart and center of the monitor TV screen coincide.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
01
13
Set the data, and press PAUSE
button.
button.
3
6
01
27
Set the data, and press PAUSE
button.
button.
4
6
02
Check that the data changes to
“01”. (Note6)
“01”. (Note6)
5
F
6F
Check that the data is “00” to
“0E”.
“0E”.
6
F
A6
Check that the data is “00” to
“3F” or “C1” to “FF”.
“3F” or “C1” to “FF”.
Note6:
The adjustment data will be automatically input to page: F, address:
60 to 70, A6.
60 to 70, A6.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
0
01
00
Set the data.
3
Turn off the power and turn on
again.
again.
4
Perform “Flange Back Check”.
Minipattern box
Below 3 cm
Camcorder
Camera
table
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Need not connected
Regulated power supply
Output voltage : Specified voltage
±
0.01Vdc
Output current : more than 3.5A
Fig. 6-1-9.
6-24
DCR-HC1000/HC1000E
5. Flange Back Adjustment (Using Flange Back
Adjustment Chart and Subject More Than 500m Away)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
5-1. Flange Back Adjustment (1)
Subject
Flange back adjustment chart
(2.0 m from the lens)
(Luminance: 350 ± 50 lux)
(2.0 m from the lens)
(Luminance: 350 ± 50 lux)
Measurement Point
Adjustment remote commander
Measuring Instrument
Adjustment Page
F
Adjustment Address
60 to 70, A6
Specified Value
Data of page: F, address: 6F is “00” to
“0E”.
Data of page: F, address: A6 is “00” to
“3F” or “C1” to “FF”.
“0E”.
Data of page: F, address: A6 is “00” to
“3F” or “C1” to “FF”.
Note1:
This adjustment should be carried out upon completion of the
following adjustments.
“HALL Adjustment”, “MR Adjustment”
following adjustments.
“HALL Adjustment”, “MR Adjustment”
Note2:
Make the lens horizontal and perform this adjustment.
Note3:
The data of page: 0, address: 10 must be “00”.
Note4:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1)
1)
POWER ....................................................... CAMERA-TAPE
Preparations:
1)
1)
Check that at both the zoom TELE end and WIDE end, the
center of the chart and center of the monitor TV screen coincide.
center of the chart and center of the monitor TV screen coincide.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
01
13
Set the data, and press PAUSE
button.
button.
3
6
01
15
Set the data, and press PAUSE
button.
button.
4
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
5
F
6F
Check that the data is “00” to
“0E”.
“0E”.
6
F
A6
Check that the data is “00” to
“3F” or “C1” to “FF”.
“3F” or “C1” to “FF”.
Note5:
The adjustment data will be automatically input to page: F, address:
60 to 70, A6.
60 to 70, A6.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
Perform “Flange Back Adjustment
(2)”
(2)”
5-2. Flange Back Adjustment (2)
Perform this adjustment after performing “Flange Back Adjustment
(1)”.
(1)”.
Subject
Subject more than 500m away
(Subjects with clear contrast such as
buildings, etc.)
(Subjects with clear contrast such as
buildings, etc.)
Measurement Point
Check operation on TV monitor
Measuring Instrument
Adjustment Page
F
Adjustment Address
60 to 70, A6
Note1:
Make the lens horizontal and perform this adjustment.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1)
1)
POWER ....................................................... CAMERA-TAPE
Preparations:
1)
1)
Set the zoom to the TELE end and expose a subject that is
more than 500m away (subject with clear contrast such as
building, etc.). (Nearby subjects less than 500m away should
not be in the screen.)
more than 500m away (subject with clear contrast such as
building, etc.). (Nearby subjects less than 500m away should
not be in the screen.)
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
01
13
Set the data, and press PAUSE
button.
button.
3
Place a ND filter on the lens so
that the optimum image is obtain.
that the optimum image is obtain.
4
6
01
29
Set the data, and press PAUSE
button.
button.
5
6
02
Check that the data changes to
“01”. (Note4)
“01”. (Note4)
Note4:
The adjustment data will be automatically input to page: F, address:
60 to 70, A6.
60 to 70, A6.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
Turn off the power and turn on
again.
again.
3
Perform “Flange Back Check”
6-25
DCR-HC1000/HC1000E
6. Flange Back Check
Subject
Siemens star
(2.0m from the front of the lens)
(Luminance: 300 ± 50 lux)
(2.0m from the front of the lens)
(Luminance: 300 ± 50 lux)
Measurement Point
Check operation on TV monitor
Measuring Instrument
Specified Value
Focused at the TELE end and WIDE
end.
end.
Note1:
The data of page: 0, address: 02 must be “06”.
Note2:
The data of page: 0, address: 10 must be “00”.
Switch setting:
1)
1)
POWER ....................................................... CAMERA-TAPE
Note3:
When the auto focus is ON, the lens can be checked if it is focused
or not by observing the data on the page 1 of the adjustment remote
commander.
1) Select page: 0, address: 03, and set data: 0F.
2) Page 1 shows the state of the focus.
or not by observing the data on the page 1 of the adjustment remote
commander.
1) Select page: 0, address: 03, and set data: 0F.
2) Page 1 shows the state of the focus.
1 : 00 : XX
Odd: Focused
Even: Unfocused
Even: Unfocused
Checking method:
1)
1)
Place the Siemens star 2.0m from the front of the lens.
2)
To open the IRIS, decrease the luminous intensity to the
Siemens star up to a point before noise appear on the image.
Siemens star up to a point before noise appear on the image.
3)
Shoot the Siemens star with the zoom TELE end.
4)
Set the FOCUS switch to AUTO.
5)
Check that the lens is focused (Note3).
6)
Set the FOCUS switch to MANUAL.
7)
Change the zoom to the TELE side from the WIDE side, and
observe the TV monitor and check that the lens is focused.
observe the TV monitor and check that the lens is focused.
Processing after Completing Adjustments:
1)
1)
Select page: 0, address: 03, and set data: 00.
Click on the first or last page to see other DCR-HC1000 / DCR-HC1000E (serv.man4) service manuals if exist.