Sony DCR-DVD403 / DCR-DVD403E / DCR-DVD803 / DCR-DVD803E (serv.man3) Service Manual ▷ View online
6-45
DCR-DVD403/DVD403E/DVD803/DVD803E
Adjustment remote commander
RM-95 (J-6082-053-B)
RM-95 (J-6082-053-B)
PC
(The SeusCam must be installed in the PC.)
OS: Windows 2000/XP
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
Three connectors are required.
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
Three connectors are required.
POWER Adjustment
Optical power meter
(J-6082-569-A)
(J-6082-569-A)
Optical sensor disc
(J-6082-570-A)
(J-6082-570-A)
To REMOTE
connector
connector
To DRIVE (Note 2)
HASP Key
USB cable
(1-829-868-41)
(1-829-868-41)
To DC IN jack
AC IN
AC adaptor
2-1-2.
Connection
1) Connect the apparatuses as shown below, and perform adjustment.
Note 1:
Before performing the adjustment, set the following data by using the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press the PAUSE button.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press the PAUSE button.
This setting is cancelled if the
[SET]
button in “After completing the TEST” of the AUDIT is clicked.
Fig. 6-2-2
Note 2:
Refer to “How to Set the Optical Sensor Disc”.
6-46
DCR-DVD403/DVD403E/DVD803/DVD803E
Pickup Lens (Laser Diode)
2-1-4.
Precautions on Adjustment
1.
Adjustment data
The adjustment data for the drive block are recorded to the IC4403
on the MD-114 board.
These data cannot be read or written from the adjustment remote
commander or SeusCam, unlike the camera and LCD adjustment
data.
Accordingly, be sure to adjust all items of the drive adjustment
when the following parts were replaced:
on the MD-114 board.
These data cannot be read or written from the adjustment remote
commander or SeusCam, unlike the camera and LCD adjustment
data.
Accordingly, be sure to adjust all items of the drive adjustment
when the following parts were replaced:
•
Drive block
•
Mounted MD-114 board
2.
Order of adjustment
Adjust the drive block in the following order:
1) POWER Adjustment
2) DVD-R Adjustment
3) DVD-RW Adjustment
4) DVD+RW Adjustment
1) POWER Adjustment
2) DVD-R Adjustment
3) DVD-RW Adjustment
4) DVD+RW Adjustment
3.
Precaution on the laser diode
In the POWER Adjustment, operate the drive with the disc cover
left open. During the adjustment, be sure to observe the fol-
lowing precautions:
1) Set the optical sensor disc correctly.
2) Keep the distance of more than 30 cm apart from the
left open. During the adjustment, be sure to observe the fol-
lowing precautions:
1) Set the optical sensor disc correctly.
2) Keep the distance of more than 30 cm apart from the
camcoder.
3) Work on the LCD screen side of the camcoder (opposite
side of the drive).
Note:
Laser light of the equipment is focused by the object lens
in the optical pick-up so that the light focuses on the reflec-
tion surface of the disc
Therefore, be sure to keep your eyes more then 30 cm apart
from the object lens when you check the emission of laser
diode
in the optical pick-up so that the light focuses on the reflec-
tion surface of the disc
Therefore, be sure to keep your eyes more then 30 cm apart
from the object lens when you check the emission of laser
diode
Fig. 6-2-5
Fig. 6-2-3
2-1-3.
How to Set the Optical Sensor Disc
1) Fit a lug on the sensor side of optical sensor disc in the hole of
the drive.
2) Push in the optical sensor disc until it clicks in the same man-
ner as when setting a disc.
Fit a lug in the
hole of drive.
hole of drive.
Fig. 6-2-4
6-47
DCR-DVD403/DVD403E/DVD803/DVD803E
2-1-5.
Alignment disc
To diagnose and adjust the drive block, the discs listed in the following table are used.
Note 1:
Use the specified disc that matches each diagnostic and adjustment item. (A message is displayed by the AUDIT)
If a wrong disc is used, the disc could be destroyed and could not be reused.
If a wrong disc is used, the disc could be destroyed and could not be reused.
Note 2:
Handle the disc with care, and before use, check if the disc is scratched or dirty.
Note 3:
If the DVD-R for Self Jitter Disc, DVD-RW DOW Disc and DVD+RW Reference Disc exceeds the use limit, the following
message will be displayed. Replace it with a new disc and click the OK button in the message window.
message will be displayed. Replace it with a new disc and click the OK button in the message window.
Name
DVD-R
Reference Disc
Reference Disc
DVD-R
for Self Jitter Disc
for Self Jitter Disc
DVD-RW
Reference Disc
Reference Disc
DVD-RW
DOW Disc
DOW Disc
DVD+RW
Reference Disc
Reference Disc
Use
Diagnosis and adjustment of DVD-R
Diagnosis and adjustment of DVD-R
Diagnosis and adjustment of DVD-RW
Diagnosis and adjustment of DVD-RW
Diagnosis and adjustment of DVD+RW
Remark
Useable counts are limitless, unless scratched.
Use a new blank disc of DMR30 (commercial DVD-R disc).
This disc can be used about 160 times for the diagnosis and adjust-
ment. (Note 3)
The record address of the disc is controlled by the AUDIT, and ac-
cordingly prepare exclusive disc for each AUDIT.
If the disc is replaced before the use limit, the setting must be re-
newed with the “<DVD-R> Write Address”.
This disc can be used about 160 times for the diagnosis and adjust-
ment. (Note 3)
The record address of the disc is controlled by the AUDIT, and ac-
cordingly prepare exclusive disc for each AUDIT.
If the disc is replaced before the use limit, the setting must be re-
newed with the “<DVD-R> Write Address”.
Useable counts are limitless, unless scratched.
This disc can be used about 400 times for the diagnosis and adjust-
ment. (Note 3)
ment. (Note 3)
This disc can be used about 660 times for the diagnosis and adjust-
ment. (Note 3)
ment. (Note 3)
Table 6-2-1
Fig. 6-2-6
6-48
DCR-DVD403/DVD403E/DVD803/DVD803E
2-2.
AUDIT (Drive Adjustment Program)
2-2-1.
Installation Method
Extract the compressed file (drive_adj.zip) in the ZIP format. If the extracted file (AUDIT for Service.msi) is executed, the installer will
start. Perform the installation following the instructions given on the screen of the installer.
start. Perform the installation following the instructions given on the screen of the installer.
2-2-2.
AUDIT Starting Method
Click the
[Start]
button on the task bar, and from the
[Programs]
, click
[AUDIT for Service]
–
[AUDIT for Service]
, and the AUDIT will
start. The SeusCam starts simultaneously with the start of AUDIT, and the operation screen appears only for a moment.
Again, the SeusCam starts and the operation screen is displayed, and after it is minimized for display at the lower left of the desktop, the
AUDIT operation screen appears. If the SeusCam cannot start (because, for instance, the HASP key is not connected to the PC), the
AUDIT also does not start.
Again, the SeusCam starts and the operation screen is displayed, and after it is minimized for display at the lower left of the desktop, the
AUDIT operation screen appears. If the SeusCam cannot start (because, for instance, the HASP key is not connected to the PC), the
AUDIT also does not start.
2-2-3.
Description of Screen
1. Diagnosis section
2. Adjustment section
3. Comment display section
4. Status display section
5.
[SET]
button
7. Menu section
6.
[STOP]
button
8. Caution display section
Fig. 6-2-7
Click on the first or last page to see other DCR-DVD403 / DCR-DVD403E / DCR-DVD803 / DCR-DVD803E (serv.man3) service manuals if exist.