DOWNLOAD Sony DCR-DVD105 / DCR-DVD105E / DCR-DVD605 / DCR-DVD605E (serv.man4) Service Manual ↓ Size: 1.42 MB | Pages: 82 in PDF or view online for FREE

6-30

DCR-DVD105/DVD105E/DVD605/DVD605E_ADJ

The adjustment items of camera system adjustment are as listed in
Table 6-1-3. The Automatic Adjustment Program divides the ad-
justment items into five, camera adjustment 1-5. Clicking either
CAMERA Adjustment Start button allows the adjustment item
which corresponds to that button to be executed.
The adjustment conditions of the subject and filter vary depend-
ing on which item is adjusted. The Adjustment Program displays
an instruction for the subject and filter as a message during the
adjustment.

CAMERA
Adjustment 1

HALL Adj.

Not required

0F

12 to 18

Siemens star chart with ND filter for
minipattern box (Note 1) or
Flange back adjustment jig

Flange back adjustment chart and
subject more than 500 m away

CAMERA
Adjustment 3

Flange Back Check

Siemens star chart

–

–

F No. Standard Data Input

0F

1C to 23

Color Reproduction Adj.

0F

33, 35, 3A, 3B

LV Standard Data Input

0F

1A, 1B

AWB Check

Clear chart
(Color reproduction adjustment frame)
ND filter 1.0, 0.4 and 0.1

–

–

MAX GAIN Adj.

Clear chart
(Center frame)

0F

19

CAMERA
Adjustment 5

Steady Shot Check

Not required

–

–

0F

2A to 2D

Color bar chart
(Color reproduction adjustment frame)

0F

2E to 31, 3E to 41

AWB Adj.

Clear chart
(Color reproduction adjustment frame)
Filter C14 for color temperature
correction

0F

44 to 55

CAMERA
Adjustment 4

Clear chart
(Color reproduction adjustment frame)

AWB Standard Data Input

Not required

Flange Back Adj.

CAMERA
Adjustment 2

Dark Siemens star chart.

6-31

DCR-DVD105/DVD105E/DVD605/DVD605E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. HALL Adj.
3. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 1.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) If “1. Data Setting during Camera Adj.” completed success-

fully, and the items “2. HALL Adj.” and “3. Release of Data
Setting during Camera Adj.” will be executed.

5) Upon successful completion of all items of the CAMERA

Adjustment 1, the following message is displayed. Click the
[OK] button.

6-32

DCR-DVD105/DVD105E/DVD605/DVD605E_ADJ

[Preparation (Using the flange back adjustment jig)]
(Illuminance: 300 to 400 lux)
1) Install the flange back adjustment jig so that the distance be-

tween it and the front of lens of camera is less than 3 cm.

2) Make the height of flange back adjustment jig and the camera

equal.

3) Check that the center of chart meets the center of shot image

screen with the zoom lens at TELE end and WIDE end respec-
tively.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back Adj.” and “3.

Release of Data Setting during Camera Adj.” will be executed.

5) Upon successful completion of all items of the CAMERA

Adjustment 2, the following message is displayed. Click the
[OK] button.

Flange back adjustment jig

Below 3 cm

Camera

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back Adj.
3. Release of Data Setting during Camera Adj.

[Preparation (Using the minipattern box)]
1) The minipattern box is installed as shown in the following fig-

ure.

 The attachment lenses are not used.

2) Install the minipattern box so that the distance between it and

the front of lens of camera is less than 3 cm.

3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the

specified voltage 

± 0.01 Vdc.

5) Check that the center of Siemens star chart meets the center of

shot image screen with the zoom lens at TELE end and WIDE
end respectively.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjustment the power sup-
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the
minipattern box.

Minipattern box

Below 3 cm

Camera

Red (+)

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Regulated power supply

Output voltage : Specified voltage 

±

 0.01 Vdc

Output current : more than 3.5 A

6-33

DCR-DVD105/DVD105E/DVD605/DVD605E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back (1) Adj.
3. Release of Data Setting during Camera Adj.

[Preparation]
1) Place the Flange back adjustment chart at 2 m position away

from the lens.

2) Check that the center of Flange back adjustment chart meets

the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.

[Adjusting method]
1) Click the [Start $1%] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back (1) Adj.” and “3.

Release of Data Setting during Camera Adj.” will be executed.

5) Upon successful completion of all items of the CAMERA

Adjustment 2 (1), the following message is displayed. Click
the [OK] button.

6) Perform “CAMERA Adjustment 2 (2)”.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back (2) Adj.
3. Release of Data Setting during Camera Adj.

[Preparation]
1) Set the zoom lens to the TELE end and expose a subject that is

more than 500 m away.

(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the screen)

[Adjusting method]
1) Click the [Start $2%] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back (2) Adj.” will be

executed.
The following message is displayed during the execution of
adjustment, and then place the ND filter on the lens so as to
obtain the optimum image.

5) If “2. Flange Back Adj.” completed successfully, “3. Release

of Data Setting during Camera Adj.” will be executed.

6) Upon successful completion of all items of the CAMERA

Adjustment 2 (2), the following message is displayed. Click
the [OK] button.