DOWNLOAD Sony DCR-DVD105 / DCR-DVD105E / DCR-DVD605 / DCR-DVD605E (serv.man4) Service Manual ↓ Size: 1.42 MB | Pages: 82 in PDF or view online for FREE

6-46

DCR-DVD105/DVD105E/DVD605/DVD605E_ADJ

1) Connect the apparatuses as shown below, and perform adjustment.

Before connecting the USB cable, set the following data by using the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press the PAUSE (Write) button.

This setting is cancelled if the [SET] button in “After completing the TEST” of the AUDIT is clicked.

Refer to “How to Set the Optical Sensor Disc”.

POWER Adjustment

Optical power meter
(J-6082-569-A)

Optical sensor disc
(J-6082-570-A)

To DRIVE (Note 2)

PC 

(The SeusCam must be installed in the PC.)

OS: Windows 2000/XP
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
         Three connectors are required.

USB cable
(1-829-579-61)

 To DC IN jack

AC IN

AC adaptor
AC-L25A/L25B
(1-479-288-11)

Audio R

Audio L

Video

S Video

To A/V jack

Adjustment remote 
commander

RM-95
(J-6082-053-B)

Multi cable
for service
(J-6082-535-A)

NEW LANC JIG
(J-6082-565-A)
LANC cable
(J-6082-442-A)

LANC

HASP Key

USB cable
(1-829-579-61)

FP-339 flexible board
(1-867-583-21)

6-47

DCR-DVD105/DVD105E/DVD605/DVD605E_ADJ

1) Before setting the optical sensor disc, remove a lug on the sensor

side of the disc.

2) Push in the optical sensor disc until it clicks same as when a

disc is set, and adjust the position so that the cable from the
sensor comes just above the pickup lens, as shown below.
After positioning, fix the disc with a tape so that it does not
rotate.

This part should come just above the pickup

Fix with a tape

The adjustment data for the drive block are recorded to the IC4202
on the VC-421 board.
These data cannot be read or written from the adjustment remote
commander or SeusCam, unlike the camera and LCD adjustment
data.
Accordingly, be sure to adjust all items of the drive adjustment
when the following parts were replaced:
• Drive block

• Mounted VC-421 board

• IC4001 (RF process) on the VC-421 board

• IC4101 (DVD DSP) on the VC-421 board

• IC4302 (DVD mecha drive) on the VC-421 board

Adjust the drive block in the following order:
1) POWER Adjustment
2) DVD-R Adjustment
3) DVD-RW Adjustment
4) DVD+RW Adjustment

In the POWER Adjustment, operate the drive with the disc cover
left open. During the adjustment, be sure to observe the fol-
lowing precautions:
1) Set the optical sensor disc correctly.
2) Keep  the distance of more than 30 cm apart from the

camcoder.

3) Work on the LCD screen side of the camcoder (opposite

side of the drive).

Laser light of the equipment is focused by the object lens
in the optical pick-up so that the light focuses on the reflec-
tion surface of the disc.
Therefore, be sure to keep your eyes more then 30 cm apart
from the object lens when you check the emission of laser
diode.

Pickup Lens (Laser Diode)

Remove this lug

6-48

DCR-DVD105/DVD105E/DVD605/DVD605E_ADJ

To diagnose and adjust the drive block, the discs listed in the following table are used.

Use the specified disc that matches each diagnostic and adjustment item. (A message is displayed by the AUDIT)
If a wrong disc is used, the disc could be destroyed and could not be reused.

Handle the disc with care, and before use, check if the disc is scratched or dirty.

If the DVD-R for Self Jitter Disc, DVD-RW Reference + DOW Disc and DVD+RW Reference Disc exceeds the use limit, the
following message will be displayed. Replace it with a new disc and click the OK button in the message window.

Name

DVD-R
Reference Disc

DVD-R
for Self Jitter Disc

DVD-RW
Reference + DOW
Disc

DVD+RW
Reference Disc

Use

Diagnosis and adjustment of DVD-R

Diagnosis and adjustment of DVD-R

Diagnosis and adjustment of DVD-RW

Diagnosis and adjustment of DVD+RW

Remark

Useable counts are limitless, unless scratched.

Use a new blank disc of DMR30 (commercial DVD-R disc).
This disc can be used about 160 times for the diagnosis and adjust-
ment. (Note 3)
The record address of the disc is controlled by the AUDIT, and ac-
cordingly prepare exclusive disc for each AUDIT.
If the disc is replaced before the use limit, the setting must be re-
newed with the “<DVD-R> Write Address”.

This disc can be used about 400 times for the diagnosis and adjust-
ment. (Note 3)

This disc can be used about 660 times for the diagnosis and adjust-
ment. (Note 3)

6-49

DCR-DVD105/DVD105E/DVD605/DVD605E_ADJ

Extract the compressed file (drive_adj.zip) in the ZIP format. If the extracted file (AUDIT for Service.msi) is executed, the installer will
start. Perform the installation following the instructions given on the screen of the installer.

Click the 

[Start]

 button on the task bar, and from the 

[Programs]

, click 

[AUDIT for Service]

 – 

[AUDIT for Service]

, and the AUDIT will

start. The SeusCam starts simultaneously with the start of AUDIT, and the operation screen appears only for a moment.
Again, the SeusCam starts and the operation screen is displayed, and after it is minimized for display at the lower left of the desktop, the
AUDIT operation screen appears. If the SeusCam cannot start (because, for instance, the HASP key is not connected to the PC), the
AUDIT also does not start.

1. Diagnosis section

2. Adjustment section

3. Comment display section

4. Status display section

5. 

[SET]

 button

7. Menu section

6. 

[STOP]

 button

8. Caution display section

2.XX