Sony BDP-CX7000ES Service Manual ▷ View online
BDP-CX7000ES
5
ALIGNMENT OF GEAR (CAM) PHASE WITH DOOR ASSY
MB-124-MEGA-EJ AND VP-062EJ BOARDS SERVICE POSITION
• It is necessary to connect MB-124-MEGA-EJ board (CN904) and IMD (ES) board (CN3005) with the extension cable to do the setting
• It is necessary to connect MB-124-MEGA-EJ board (CN904) and IMD (ES) board (CN3005) with the extension cable to do the setting
to this position.
Prepare the following extension cables.
Part No. J-2501-068-A (19 pin, 1.00 mm pitch)
MB-124-MEGA-EJ board
VP-062EJ board
insulation
Connect jig (extension cable)
to the IMD board (CN3005)
to the IMD board (CN3005)
CN904
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C106) to
discharge the capacitor (C106).
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C106) to
discharge the capacitor (C106).
HARNESS SETTING ON SWITCHING REGULATOR
Note: This illustration sees the switching regulator from component side.
door assy
gear (cam)
Align a slit of door assy with a marking on
the bottom land of gear tooth when the gear
is rotated fully in arrow direction, as shown.
the bottom land of gear tooth when the gear
is rotated fully in arrow direction, as shown.
C106
800
:/2 W
– Switching Regulator (Conductor Side) –
clamp (L35)
AC inlet (2P) harness
harness
wire
switching
regulator
regulator
BDP-CX7000ES
6
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-2. CASE
(Page
(Page
7)
2-3. VP-062EJ
BOARD
(Page
7)
2-4. AUES
BOARD
(Page
8)
2-6. CHASSIS-M (ES) BLOCK
(Page
(Page
9)
2-7. FRONT PANEL BLOCK
(Page
(Page
9)
2-5. MB-124-MEGA-EJ
BOARD
(Page
8)
2-8. 400D
TABLE
ASSY
(Page
10)
2-9. DRV
BOARD
(Page
10)
2-10. TABLE (DOOR) ASSY
(Page
(Page
11)
2-11. DC MOTOR (DOOR) (M201)
(Page
(Page
11)
2-17. BU (KEM-430AAA) ASSY
(Page
(Page
15)
2-19. SWITCHING REGULATOR
(Page
(Page
17)
2-20. BASE (CDM BD) BLOCK
(Page
(Page
18)
2-18. OPTICAL PICK-UP BLOCK
(KEM-430AAA)
(Page
(KEM-430AAA)
(Page
16)
2-12. HOLDER (TABLE SENSOR 400)
(Page
(Page
12)
2-14. SDO BOARD
(Page
(Page
13)
2-21. MOTOR (400 BD) ASSY (LOADING) (M301)/
(TABLE) (M302), MLD BOARD
(Page
18)
2-22. SLK BOARD, SLD BOARD
(Page
(Page
19)
2-15. POP-UP (400) ASSY
(Page
(Page
14)
2-13. SDT BOARD, SDR BOARD
(Page
(Page
12)
2-16. BACK PANEL BLOCK
(Page
(Page
14)
SET
BDP-CX7000ES
7
1 five screws (BVST4 u 8)
2 two flat head screws (TP)
2 three flat head screws (TP)
1 five screws (BVST4 u 8)
3 case
Note: Follow the disassembly procedure in the numerical order given.
2-2. CASE
2-3. VP-062EJ BOARD
4 five screws
(BVTP3
u 8)
4 five screws (BVTP3 u 8)
5 connector (CN104)
6 VP-062EJ board
3 screw (B3 u 6)
1 connector (CN802)
2 wire (flat type)
(21 core) (CN801)
BDP-CX7000ES
8
3 two screws (BVTP3 u 8)
4 five screws (BVTP3 u 8)
3 screw (BVTP3 u 8)
5 AUES board
1 connector (CN102)
2 wire (flat type)
(26 core) (CN101)
2-4. AUES BOARD
2-5. MB-124-MEGA-EJ BOARD
3 two connectors
(CN301,
CN600)
4 SATA harness
(CN700)
1 wire (flat type) (26 core)
(with ferrite core) (CN803)
6 two screws (BVTP3 u 8)
6 three screws (BVTP3 u 8)
7 three solders
8 heat sink (ES)
9 radiation sheet (F)
qa MB-124-MEGA-EJ board
2 wire (flat type)
(21 core) (CN801)
5 wire (flat type)
(19 core) (CN904)
0 cushion (panel front)
Click on the first or last page to see other BDP-CX7000ES service manuals if exist.