DOWNLOAD Sony BDP-CX7000ES Service Manual ↓ Size: 9.16 MB | Pages: 127 in PDF or view online for FREE

ERRLOG_

CATEGORY_

THERMO

Shutdown due to 

temperature rise of 

the set

FAN ERR

0x05

0x01

Check the ambient temperature of 
the set

FAN is defective

FAN ERR

0x02

Replace the fan

ERRLOG_

CATEGORY_

NVRAM

NAND Error

E7001

0x07

0x01

Reboot the set, and if the error 
recurs or if the set malfunctions, 
perform the service. (When the error 
persists though NVRAM is forcibly 
initialized, replace the NAND. All the 
data in NVRAM including the setting 
information are initialized)

E7002

0x02

E7003

0x03

E7004

0x04

E7005

0x05

Reboot the set for automatic recov-
ery. If the error recurs, perform the 
service. (When the error persists 
though NVRAM is forcibly initialized, 
replace the NAND. All the data in 
NVRAM including the setting infor-
mation are initialized)

E7006

0x06

E7007

0x07

E7008

0x08

E7009

0x09

E7010

0x0A

E7011

0x0B

NAND 

(SdmRegistry) 

Error

E7101

0x65

Reboot the set and if the error oc-
curs, perform the service. (Replace 
the NAND because it reached the 
life)

E7102

0x66

E7103

0x67

E7104

0x68

E7105

0x69

N/A

NAND (Database) 

Error

E9101

No error log is recorded.

Reboot the set, and if the error 
recurs, perform the service. (When 
the error persists though the “Fac-
tory Initialize” is done, replace the 
NAND. All the data including setting 
information are initialized)

E9102

E9103

E9104

ERRLOG_

CATEGORY_

MECHA

Mechanism 

error that cannot be 

specifi ed

E8000

0x09

0x00

Mechanical error. Check the each 
motion and perform the service.

Fails the door 

close in initializing 

mechanism

E8001

0x01

Check the door mechanism. (Gear 
alignment, switch condition, Assem-
bly of the door guide rail) 

Makes an error 

while the table is 

operating

E8002

0x02

Check the sensor alignment. (espe-
cially the table sensor alignment)/
Check the table mechanism. (As-
sembly of gears, teeth of Table (400) 
for sensor)

Makes an error 

while the loading is 

operating

E8003

0x03

Check the loading mechanism and 
perform the service.

Makes an error 
while Popper is 

operating

E8004

0x04

Check the pop-up mechanism. 
(especially POP-UP lever alignment) 
And check the door mechanism. 
(Pop-Up is common mechanism with 
door’s)

N/A

Drive Tray Error

E8902

No error log is recorded.

Reboot the set, and if the error 
recurs, perform the service. (Check 
optical drive)

J-6090-199-A

BLX-104

Single Layer

J-6090-200-A

BLX-204

Dual Layer

3-702-101-01

CD (YEDS-18)

J-6090-088-A

HLX-504

Single Layer (NTSC)

J-6090-089-A

HLX-505

Dual Layer (NTSC)

J-6090-077-A

HLX-506

Single Layer (PAL)

J-6090-078-A

HLX-507

Dual Layer (PAL)

Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-

989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.

1. BLX-104
Procedure:
1. Select 

23.976Hz/1080p.

2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
4.  Check each outputs.
 Video:
 Composite/S 

Video/component/HDMI.

 Audio:
 Speaker 

out.

*  When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) 

can use instead of 1080/24p.

 

However this is temporary correspondence.

*  When the output of HDMI is 1080p, the signal of Composite/S 

Video/Component are not output.

 

It is necessary to lower the output of HDMI to 1080i or less.

2. BLX-204
Procedure:
1.  Select 1080i (59.94Hz or 50Hz).
2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
 

(Check the picture and sound output)

3. CD (YEDS-18)
Procedure:
Check whether player can play back or not.
(Check the sound output)

4.  HLX-504/505 (NTSC), HLX-506/507 (PAL)
Procedure:
1.  After displayed Main Menu, select “1.Video signal”.
2.  Play “1.Color bar 100%”.
 

(Check the picture and sound output)

3.  Return to Menu.
4.  Play “Demonstration 4:3” or “Demonstration 16:9”.
 

(Check the picture and sound output)

4-1-2.  Playback operation confi rmation
Confi rm operation in each signal/output mode of test disc (BLX-
104/204) according to the content of the repair.

Note: “AV Sync.” doesn’t operate.

When trouble is found in the table stop and the detection of the 
disc, or the adjustment part is taken apart, it is necessary to do the 
following adjustments over again.

1. INTRODUCTION
1-1.  Adjustment item and the order
1.  POP UP MECHANISM ADJUSTMENT
2. TABLE 

SENSOR 

ADJUSTMENT

3.  DISC DETECT SENSOR ADJUSTMENT
4. SENSOR 

LEVEL 

ADJUSTMENT

A long screwdriver is necessary to “Table sensor adjustment”.

1-3.  Wiring for adjustment
The oscilloscope and the harness are prepared.

It is easy to work when the harness (wire with the connector) like 
fi gure above is made. It is possible to substitute it by measuring the 
waveforms of JL5021 and JL5022 by the short-circuit of JL5020 
and JL5024 when there is no harness.

1-4.   Entering the mechanical adjustment mode
Procedure:
1.  Step 1-3 is connected and the power cord of the set is inserted.
2.  The message “ADJUST MODE” is appears on the fl uorescent 

indicator tube.

3.  Press the [

N

] button, The message “TABLE_ADJUST *” is 

appears on the fl uorescent indicator tube, and entering table 
adjust mode.

 Press 

the 

[

X

] button, The message “DISC_ADJUST *” is ap-

pears on the fl uorescent indicator tube, and entering disc sen-
sor adjust mode. 

 

Press the [

x

] button, The message “ADJUST_MODE *” is 

appears on the fl uorescent indicator tube, and return the adjust-
ment menu.

3. TABLE  SENSOR  ADJUSTMENT
Procedure:
1.  The case is detached. Step 1-3 is connected and the power cord 

of the set is inserted.

2.  Press the [

N

] button, The message “TABLE_ADJUST *” is 

appears on the fl uorescent indicator tube, and entering table 
adjust mode. Table is locked (refer to Fig. 5).

3.  The message “TABLE HH: x T4: x” is appears on the fl uo-

rescent indicator tube.

4.  The screw (PTTWH3X6) that is the fi xation of the holder (ta-

ble sensor 400) is loosened (the screw is not detached).

5.  The holder is moved right and left (Fig. 6), and as for “x” of 

“TABLE HH:”, it always light, and “x” of “T4:” searches for 
the position of the verge whether light (it is acceptable even if 
it does not light if it is a verge).

6.  The screw of step 4 is fi xed in the state of step 5.
7. It 

is 

confi rmed that the table is moved by the hand (move only 

a little because it is locked), and “x” of “T4:” blinks.

2. POP  UP  MECHANISM  ADJUSTMENT
Procedure:
1.  The case is detached. Step 1-3 is connected and the power cord 

of the set is inserted.

2.  Press the [

N

] button, The message “TABLE_ADJUST *” is 

appears on the fl uorescent indicator tube, and entering table 
adjust mode. Table is locked (refer to Fig. 1).

3.  The cover chassis is removed, and the screw is loosened (the 

screw is not detached) (refer to Fig. 2).

4.  The door is moved by the hand, and it puts it into the state that 

there is no lever in the hole of the table.

5.  The hole and the lever of the table are matched to the center (it 

shines on with the spotlight etc. and confi rm it).

6.  It is confi rmed that there is a lever in the position of the guide-

line under the table because it does not match it to the adjoin-
ing slot (refer to Fig. 3).

7.  The door is moved by the hand, it is confi rmed that the lever 

rises to the center of the hole of the table (refer to Fig. 4).

8.  The screw of step 3 is fi xed (it is noted to tighten strongly and 

not to destroy it), and the cover chassis is installed.