Sony BDP-CX7000ES Service Manual ▷ View online
BDP-CX7000ES
17
2-19. SWITCHING REGULATOR
1 three screws (BVTP3 u 8)
8 four screws (BVTP3 u 8)
8 screw (BVTP3 u 8)
9 clamp (L35)
clamp (L35)
AC inlet (2P) harness
harness
wire
0 bracket (power ES) assy
qa switching regulator
switching regulator
2 cover (disc rear)
3 three rivets
4 shield plate power
5 three connectors
(CN202, CN204, CN205)
6 two connectors
(CN201,
CN203)
7 connector (CN101)
1 three screws (BVTP3 u 8)
Arrangement of harness
Note: This illustration sees the switching regulator from component side.
Note: This illustration sees the switching regulator from component side.
BDP-CX7000ES
18
2-20. BASE (CDM BD) BLOCK
2-21. MOTOR (400 BD) ASSY (LOADING) (M301)/(TABLE) (M302), MLD BOARD
4 twelve screws (BVTP3 u 8)
5 base (CDM BD) block
1 screw (PSW3 u 8)
3 screw (PSW3 u 8)
2 shaft (pole)
5 motor (400 BD) assy (table)
(M302)
6 MLD board
4 motor (400 BD) assy (loading)
(M301)
1 two belts (BD)
2 three screws (BVTP3 u 8)
3 two solders
3 two solders
BDP-CX7000ES
19
2-22. SLK BOARD, SLD BOARD
claws
Note for installation
When installing the
SLK board and SLD boards,
align the leads position as shown.
SLK board and SLD boards,
align the leads position as shown.
SLK board
SLD board
leads
position
position
A
B
1 Rotate the gear (pulley BD) in the
direction of the arrow
A fully.
3 Rotate the gear (pulley BD) in the
direction of the arrow
B fully.
2 screw (BVTP3 u 8)
4 screw (BVTP3 u 8)
0 screw (BVTP3 u 8)
5 SLK board
qa SLD board
6 belt (BD)
7 screw (PWH2)
base (CDM BD) block
8 gear (pulley BD)
9 gear (center BD)
BDP-CX7000ES
20
SECTION 3
TEST MODE
1. BD SERVICE MODE
Note: The operation in this mode must use a remote commander.
1-1. Setting method of the BD service mode:
1. It is confi rmed that the AC power cord is pulled out.
2. Press the [
1. It is confi rmed that the AC power cord is pulled out.
2. Press the [
x
], [OPEN/CLOSE] and [DISC EJECT] buttons, next the AC power cord is inserted.
3. The message “SERVICE MODE” appears on the fl uorescent indicator tube and enter the BD service mode (it keeps pressing the buttons
until the message is displayed).
1-2. Menu composition
1. Diag (test function)
2. Log (log display)
3. Factory Initialize (returns to the state of the factory shipment)
4. Ship Mode (ship mode setting and power off)
5. Network (network information display)
6. System Information (system information display)
1-3. Menu tree
1. Diag (test function)
2. Log (log display)
3. Factory Initialize (returns to the state of the factory shipment)
4. Ship Mode (ship mode setting and power off)
5. Network (network information display)
6. System Information (system information display)
1-3. Menu tree
Service Mode Menu
Diag
Log
Factory Initialize
Ship Mode
Network
System Information
Device Test
Audio Video Test
Changer Mecha Test
Error Log
Command Log
Ifconfig
Ping
USB Host
D/A Converter
Ifcon
I/P Converter
Glue
HD Enhancer
Video Encoder
External HDMI
Initialize
Popper Up/Down
Open/Close
Turn Left
Turn Right
Turn Around Left
Turn Around Right
Chuck/Unchuck
FDP All ON
Show Strings
LED Sequential ON
Fan Control ON
Click on the first or last page to see other BDP-CX7000ES service manuals if exist.