Sony DSLR-A700P Service Manual ▷ View online
HELP
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
HELP04-06
Grease (G-116): J-6082-628-A
1.
Apply the grease (G-116) to indicated portion of the focus ring.
2.
Wrap the focus scale plate around the focus ring and fix it with the polyester tape (Black) 10mm (7
×
25mm).
Note:
Confirm the part A slides in the arrow direction.
Note:
Put the focus scale plate so that it is not out of the groove on the focus ring.
Apply the grease (G-116)
Focus Scale Plate
Focus Scale
Plate
Plate
Focus Scale Plate
Focus Ring
Groove of the
Focus Ring
Focus Ring
Part A
Hole B
Polyester Tape
(Black)10mm
(7X25mm)
(Black)10mm
(7X25mm)
Polyester Tape
(Black)10mm
(7X25mm)
(Black)10mm
(7X25mm)
A
A
Hole B
HELP
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
HELP04-07
1.
Peel off the release paper (on the focus pattern side) of CL block, lay it and insert it into the square hole on outer barrel. (Fig. a)
2.
Stand CL-002 block up. (Fig. b)
3.
Put the tip of CL-002 block to the edge (Part A) on outer barrel and stick it. (Fig. c)
4.
Peel off the release paper (on the zoom pattern side) of CL-002 block. (Fig. d)
5.
Stick the CL-002 block while putting it to the standard B. (Fig. e/f)
6.
Roll CL-002 block up tracing the guide line and stick it to be fitted to the corners C and D. (Fig. g/h)
7.
Peel off the release paper (on the part E) of CL-002 block, stick it to be fitted to the shape of outer barrel. (Fig. i/j)
Note:
Be to stick it so that there is no floating point at the part F. (Fig. j)
8.
Stick it fitting to the edge of outer barrel. (Fig. k)
Note:
Be sure not to bring it out to the arrow direction.
9.
Wrinkle the flexible board while pulling slightly CL-002 block.
10. Wrinkle the part G of CL-002 block lightly. (Fig. m)
Fig.a
Fig.b
Fig.c
CL-002 Block
CL-002 Block
Part A
Hole of the
Outer Barrel
Outer Barrel
CL-002 Block
Fig.d
Fig.e
Fig.f
Release Paper
Standard B
CL-002 Block
Fig.g
Fig.h
Corner D
Corner C
Fig.i
Fig.j
Part E
GL-002 Block
Part F
CL-002 Block
Fig.k
Fig.l
Fig.m
Part G
3-1
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
DISASSEMBLY
(JAPANESE)
DISASSEMBLY
(ENGLISH)
(See Page 3-2.)
9
(Note 1)
(Note 2)
1
2
3
5
4
6
6
7
8
12
10
11
3. REPAIR PARTS LIST
3-1.
EXPLODED VIEWS
3-1-1. LENS BLOCK
NOTE:
•
•
-XX and -X mean standardized parts, so they may
have some difference from the original one.
have some difference from the original one.
•
Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
seldom required for routine service. Some delay
should be anticipated when ordering these items.
•
The mechanical parts with no reference number in
the exploded views are not supplied.
the exploded views are not supplied.
(Note 1)
Select the same 3-4 interval adjustment washer (Ref. No.
9) as shipping.
9) as shipping.
Ref. No.
Part No.
Description
1
3-213-619-01 1ST LENS STOPPER BARREL
2
3-210-085-01 G1+G2
3
A-1334-689-A FIRST LENS HOLDER BLOCK
4
3-270-620-02 1ST CAM RING DECORATION PLATE
5
3-210-198-02 2ND DECORATION PLATE
6
3-218-903-01 SCREW TAPPING P1 (M1.7X3.5)
7
A-1279-372-A 2ND LENS BARREL ASSY
8
A-1319-824-A 3RD LENS BARREL ASSY
9
Selection parts 3-4 INTERVAL ADJUSTMENT WASHER (Note 1)
10
A-1279-371-A 4TH LENS BLOCK
11
3-210-177-01 4TH LENS BARREL HOLD WASHER
12
3-292-495-01 2ND BLOCK ADJUSTMENT WASHER (Note 2)
Ref. No.
Part No.
Description
(Note 1) 3-4
群間隔調整ワッシャ
(
図面番号
9)
は，出荷時と同
じ部品を選択してください。
(Note 2)
Do not change of the thickness of 2nd block adjustment
washer (Ref. No. 12) from shipping.
When replace the 2nd lens barrel assy, use the 3-292-
495-01 (t = 0.05 mm) according to result of flange back
adjustment.
washer (Ref. No. 12) from shipping.
When replace the 2nd lens barrel assy, use the 3-292-
495-01 (t = 0.05 mm) according to result of flange back
adjustment.
(Note 2) 2
群補正ワッシャ
(
図面番号
12)
は，出荷状態から
変更しないでください。
2
群レンズブロックを交換した場合は，フランジ
バック調整の結果に合わせて
3-292-495-
01(t=0.05mm)
を使用してください。
Ver. 1.2 2008.02
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
3-2
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
DISASSEMBLY
(JAPANESE)
DISASSEMBLY
(ENGLISH)
3-1-2. LENS MOUNT BLOCK
Ref. No.
Part No.
Description
51
3-210-202-02 FOCUS DIFFERENTIAL RING
52
3-210-043-02 FOCUS BRUSH
53
3-275-427-01 SCREW,TAPPING,P1 (M1.7X2.5)
54
3-210-083-01 ZOOM COUPLING PIN
55
Selection parts COUPLER ADJUSTMENT WASHER (A to E)
(Note 1)
56
3-210-039-01 AF COUPLER
57
2-698-464-01 TAPPING SCREW PHI 2 (M2.0X5.5)
58
3-210-037-01 FOCUS RUBBER RING
59
9-913-210-03 POLYESTER TAPE (BLACK) 10mm (Note 2)
60
3-210-044-01 GROUND BRUSH
61
3-210-041-01 ZOOM BRUSH
62
3-210-201-01 ZOOM BARREL
63
3-270-622-01 ZOOM RING REINFORCEMENT PLATE
64
3-210-038-01 ZOOM RUBBER RING
65
A-1279-556-A REAR BARREL ASSY
66
2-683-692-01 CHIP (MOUNT INDEX)
68
3-078-890-11 SCREW, TAPPING (M1.7X4.0)
69
Selection parts BACK ADJUSTMENT WASHER (A to E) (Note 1)
70
2-684-234-01 PRESET RING HOLDING PLATE
71
2-688-406-01 MAIN SPRING
72
Selection parts PRESET RING (Note 1)
73
A-1279-383-A MAIN SPRING GUIDE BLOCK
74
2-684-244-01 STOPPER SCREW (M1.4X1.2)
75
3-210-040-01 REAR LIGHT SHEILD BARREL
76
7-627-551-98 PRECISION SCREW +P 1.4X2.2
77
2-684-065-01 GROUND SPRING
78
2-684-066-01 TAPPING SCREW M1.7X4.0
Ref. No.
Part No.
Description
ns: not supplied
ns
(Note 1)
(Note 1)
(Note 1)
(Note 2)
(7 x 13mm)
(7 x 13mm)
(Note 2)
(7 x 13mm)
B
B
C
A
A
51
52
53
57
54
54
55
56
57
69
(See Page 3-3.)
(See Page 3-4.)
C
58
59
60
59
61
63
62
64
65
66
75
57
74
73
72
71
57
78
78
76 77
76
68
70
ns
ns
(Note 1)
The number or type of these parts need to be
selected according to adjustment etc..
Select the part referring to page 3-5.
selected according to adjustment etc..
Select the part referring to page 3-5.
(Note 2)
Cut the polyester tape (black) 10mm (per roll)
(Ref. No. 59) for specified size.
(Note 1)
これらの部品は調整などによって使用個数
や種類を選択する必要があります。
3-5
ページを参照して選択してください。
(Note 2)
ポリエステルテープ
(
黒
) 10mm (
図面番号
59)
は，指定のサイズにカットして使用して
ください。
Ver. 1.2 2008.02
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Click on the first or last page to see other DSLR-A700P service manuals if exist.