Sony DSLR-A700P Service Manual ▷ View online
2-15
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
FOCUS-SHIFT
(FOCAL LENGTH)
ADJUSTMENT
(FOCAL LENGTH)
ADJUSTMENT
FOCUS SCALE
PLATE POSITION
ADJUSTMENT
PLATE POSITION
ADJUSTMENT
7
Focus Stopper
Gear Base Plate
CL-002 Block
Gear Shaft
Fixed Barrel R Assy
Gear A
Focus Ring,
Focus Scale Plate
Focus Scale Plate
Focus Scale Plate
HELP04-05
HELP04-07
HELP04-06
Focus Ring
Polyester Tape
(Black)10mm
(7X25mm)
(Black)10mm
(7X25mm)
8
9
6
4
(From Page
2-14.)
2-14.)
(G-118)
(G-118)
(G-116)
5
Make the lens
upside down.
upside down.
HELP
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
HELP
Note for assembling and grease applying positions are shown.
HELP04-01
Grease (G-116): J-6082-628-A
Grease (G-118): J-6082-680-A
1.
Allow mount shielding O-ring to absorb all the grease (G-116) it can.
2.
After installing the mount shield O-ring, apply the grease (G-118) to the indicated portion.
HELP04-02
Adhesive bond (B-110): J-6082-617-A
1.
Install the support plate and put it in the arrow direction.
2.
Apply the adhesive bond (B-110) between the support plate and the outer cover block carefully as shown below.
Apply the grease (G-118)
Lib of the Outer Barrel
Center
Mount Shielding O-Ring
Mount Shielding O-Ring
Allow mount shielding O-ring to
absorb all the grease (G-116) it can.
absorb all the grease (G-116) it can.
To a little
over
the top
over
the top
Apply the adhesive
bond (B-110)
bond (B-110)
Support Plate
Support Plate
Outer Cover Block
Support Plate
Do not spread out
to the groove for
the Mount Shielding
O-ring
to the groove for
the Mount Shielding
O-ring
Do not apply it
to the edge of the
Outer Cover Block
to the edge of the
Outer Cover Block
HELP
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
HELP04-03
Adhesive bond (B-110) : J-6082-617-A
1.
Apply the adhesive bond (B-110) to the indicated portion.
2.
Insert the outer cover block while its projection engages with the cutout of the fixed barrel R assy.
3.
Turn the outer cover block clockwise until it stops and install it.
HELP04-04
1.
Be sure to put the focus ring reinforcement plate so that its adhesive surfaces don't go out to the pinch lever hold pin.
Apply the adhesive
bond (B-110)
bond (B-110)
Apply the adhesive
bond (B-110)
bond (B-110)
Apply the adhesive
bond (B-110)
bond (B-110)
Cutout
Cutout
Projection
Projection
Projection
Fixed Barrel R Assy
Projection
Outer Cover Block
Outer Cover Block
Outer Cover Block
Focus Ring
Reinforcement Plate
Reinforcement Plate
Pocus Ring Reinforcement Plate
Adhesive part
Pinch Lever Hold Pin
HELP
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
HELP04-05
1.
Install the focus stopper in the concave part of the focus ring and install the focus ring to the outer barrel.
Note:
When Install the focus ring, the part A is adjusted to the screw hole on the outer barrel and engage three projections of the
outer barrel with the groove of the focus ring by turning the focus ring in the arrow direction.
2.
Adjust the screw holes of the focus stopper can be seen through the long holes of the outer barrel and tighten two screws temporarily.
3.
Turn the focus ring in the near position in the arrow direction.
Note:
Be sure to position the focus scale plate as shown in the picture.
4.
While pushing focus stopper to left side tighten two screws temporarily.
Note:
Tighten lightly to the end and loosen 1/4 turn.
Note:
Refer to "Focus-shift Adjustment" for tightening up.
Focus Stopper
Groove
Outer Barrel
Outer Barrel
Projections
Projection
Projections
Screw Hole
Screw Hole
Part A
Part A
Focus Ring
Focus Ring
Focus Ring
Focus Stopper
Focus Stopper
Focus Scale Plate
Screw Holes of Focus Stopper
Long Holes of
Outer Barrel
Outer Barrel
Set the focus to near position.
Click on the first or last page to see other DSLR-A700P service manuals if exist.