Sony DSC-WX1 (serv.man3) Service Manual ▷ View online
2-5
DSC-WX1_L2
2-2-3. BT HOLDER SECTION
Follow the disassembly in the numerical order given.
1
Cabinet (Upper) Block (
1
-1 to
1
-4)
2
Lens Block (
2
-1 to
2
-3)
3
SY-233 Board (
3
-1 to
3
-4)
EXPLODED VIEW
HARDWARE LIST
1
-1
1
-4E
1
-2
HELP 01
HELP 02
HELP 03
HELP 04
1
Cabinet (Upper) Block
2
Lens Block
(Note)
2
-1
2
-3E
1
-3 (Claw)
2
-2
BT Holder Block
3
SY-233 Board
SY-233
3
-2 (#26)
3
-4E
3
-3 (Claw)
3
-1
Note: Refer to the following each item when you exchange parts of Lens Block.
•
1-2. Precaution on Replacing the Lens (page 1-1)
•
2-3. Ornamental Ring A or Barrier Assy Replacing Method (page 2-6)
•
2-4. Zoom Gear Block Replacing Method (page 2-7)
•
2-5. Tube (A) or Cam Tube Replacing Method (page 2-8)
•
2-6. Final Inspection (page 2-16)
2-6
DSC-WX1_L2
2-3. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
2
Peel off release papers of Barrier Tapes.
3
Install Ornamental Ring A and press it lightly.
Installation
1
With four claws fitted in position, install the Barrier Assy.
5
Remove Barrier Assy by disengaging four claws.
Ornamental Ring A
Ornamental Ring A
Barrier Assy
Barrier Assy
Barrier Tapes
Barrier Tape
Barrier Tape
A
Removal
1
Turn on the power switch and extend the lens.
2
Detach the battery.
3
Pour a solvent such as alcohol from two places A to the tweezers or a needle shown below into a gap of Ornamental Ring A.
4
Remove while turning the Ornamental Ring A right and left.
Solvent
Claws
Claws
Tweezers
Barrier Assy
Barrier Lever
Hole
Claws
Claws
Ver. 1.2 2010.01
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
2-7
DSC-WX1_L2
2-4. ZOOM GEAR BLOCK REPLACING METHOD
Removal
1
Remove one screw.
2
Remove the Zoom Gear Block upward.
3
Remove the Naruto Gear.
4
Remove the Z Tape.
Note:
The Z Tape is not supplied. Please reuse.
5
Disengage two claws A and B in this order to remove the FG Plate Spring.
Note:
The FG Plate Spring cannot be reused.
6
Remove two sensors on the lens flexible board.
7
Break two solders, and remove the lens flexible board.
Installation
1
Confirm the direction of Zoom Gear Block, and install the lens flexible board with two solders.
2
Install two sensors of Zoom Gear Block.
3
Engage two claws A and B in this order to install FG Plate Spring.
4
Stick the Z Tape.
5
Install Naruto Gear (S).
6
With four bosses fitted in position, install Zoom Gear Block.
7
Tighten one screw.
*
*
Tightening torque = 0.068
±
0.01N
•
m (0.7
±
0.1kgf
•
cm)
Screw
Zoom Gear Block
Zoom Gear Block
Front Side
Rear Side
FG Plate Spring
Z Tape
Sensors
Solders
Naruto Gear
Claw
A
Claw
B
Zoom Gear Block
FG Plate Spring
Z Tape
Sensors
Solders
Claw
B
Claw
A
Screw
Zoom Gear Block
Naruto Gear
Bosses
Bosses
2-8
DSC-WX1_L2
2-5. TUBE (A) ASSY OR CAM TUBE REPLACING METHOD
Close Hole Tape
Removal
1
Peel off the Close Hole Tape.
Note:
The Close Hole Tape is not supplied. Please reuse.
2
Remove the Spring.
3
Remove one screw.
4
Remove the Zoom Gear Block upward.
5
Remove the Flexible Board.
Screw
Zoom Gear Block
Spring
Tweezers
Rib
Rib
Boss
Left View
Bottom View
Top View
Right View
Rear View
Boss
Boss
Boss
Boss
Adhesive Sheet
Adhesive Sheet
Boss
Disconnect the Flexible Board
from 2-group Frame Assy.
from 2-group Frame Assy.
Click on the first or last page to see other DSC-WX1 (serv.man3) service manuals if exist.