DOWNLOAD Sony DSC-WX1 (serv.man3) Service Manual ↓ Size: 6.98 MB | Pages: 71 in PDF or view online for FREE

1-1

DSC-WX1_L2

When you replace to the repairing board, get the acquire data from the former needed for the adjustment from.
Start the Adjust Manual in the Adjust Station and perform “Restore Data” to get the data.
The data getting for this model is as follows.

• USB Serial No.

• Angular Velocity Sensor Sensitivity Adjustment (Dp/Dy Data)

When you cannot read data from the former replace the same time SY-233 board and lens.

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “Destination Data Write”.

The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB Serial No. Input”.

When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor (SE403).
Start the Adjust Manual in the Adjust Station and execute the “Angular Velocity Sensor Sensitivity Adjustment”, input the data written down.

1.

The AF-122 board is soldered onto the lens.
When replacing the lens, transfer the AF-122 board to the new lens.

2.

When replacing the lens, write down the PITCH/YAW data given on the data sheet of the replacement lens for service.
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj”.

The PITCH/YAW data of lens are written only repair parts.

SE403

PPP

YYY

PPP : PITCH sensor sensitivity

YYY : YAW sensor sensitivity

The sensor sensitivity of SE403 of SY-233 board are written only repair parts.

P.PP/Y.YY

PITCH/YAW Data

P.PP / Y.YY

YAW Data
PITCH Data

1-2

DSC-WX1_L2

Copies all images in the internal memory to a “Memory Stick Duo” media.

1 Insert a “Memory Stick Duo” media with sufficient free capacity into the 

camera

2 MENU U 

 (Settings) 

U 

 (“Memory Stick” Tool) 

U [Copy] U [OK] 

U [ on the control button

• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little

remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

• Images cannot be copied individually.
• The original images in the internal memory are retained even after copying. To delete the contents of the 

internal memory, remove the “Memory Stick Duo” media after copying, then format the internal memory 
([Format] in [Internal Memory Tool]).

• A new folder is created on the “Memory Stick Duo” media and all the data will be copied to it. You 

cannot choose a specific folder and copy images to it.

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)

When replacing the SY-233 board, erase the data in internal memory of the board before replacement.

When replacing the SY-233 board, execute formatting and initialize the internal memory after replacement.

Formats the “Memory Stick Duo” media or the internal memory. A commercially available
“Memory Stick Duo” media is already formatted, and can be used immediately.

1 MENU U 

 (Settings) U 

 (“Memory Stick” Tool) or 

 (Internal

Memory Tool) U [Format] U [OK] U [ on the control button

• Note that formatting permanently erases all data including even protected images.

1-3

DSC-WX1_L2

Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust
Station.

1)

Start the Adjust Manual from the Adjust Station.

2)

Click 

 (Write Enable Tool) button.

3)

Click “Active Write Enable Mode” button.

4)

Upon completion of the setting change, the following message will be displayed.

5)

Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).

6)

Write the data read out into the PC to the internal memory of the camera.

7)

Disconnect the PC from the camera, and turn off the camera.

By turning off the camera, the write enable setting is reset.

1-4

DSC-WX1_L2

When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.

When problems occur while the unit is operating, the LCD screen
shows a 4-digit display consisting of an alphabet and numbers, which
blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”
of the problem.

0 0

3 2

C

Repaired by:

Refer to “1-5-3. Self-diagnosis Code Table”.

Indicates the appropriate
step to be taken.
E.g.
13 ....Format the “Memory Stick Duo”.
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2 Hz

C : Corrected by customer
E : Corrected by service

engineer

LCD screen