Sony DSC-WX1 (serv.man3) Service Manual ▷ View online
2-13
DSC-WX1_L2
qs
Match seven convex parts of the Main Assy to seven ditches of the Fixed Tube and install it.
qd
Install the Naruto Gear on the Fixed Tube.
qf
Rotate the Naruto Gear and the lens is drawn out.
qg
Pass the Flexible Board through the hole of the Fixed Tube.
qh
Fix two claws of the Flexible Board into ribs of the Fixed Tube.
qj
Rotate the Naruto Gear and the lens is retractile.
Main Assy
Naruto Gear
Naruto Gear
Eyepiece Side View
Fixed Tube
Fixed Tube
Fixed Tube
Claws
Naruto Gear
Flexible Board
2-14
DSC-WX1_L2
qk
Install the Rear Mirror Tube Assy on the Main Assy.
Note:
Do not pinch the Flexible Board between the Rear Mirror Tube Assy and the Main Assy.
ql
Tighten up four screws in order of 1
→ 2 → 3 → 4.
*
Tightening torque = 0.068
±
0.01N
•
m (0.7
±
0.1kgf
•
cm)
Rear Mirror Tube Assy
1
3
4
2
w;
Arrange the Flexible Board.
Main Assy
Rib
Rib
Boss
Left View
Bottom View
Top View
Right View
Rear View
Boss
Boss
Boss
Boss
Adhesive Sheet
Adhesive Sheet
Boss
Connect the Flexible Board
from 2-group Frame Assy.
from 2-group Frame Assy.
2-15
DSC-WX1_L2
wd
Hook the Spring.
wf
Stick the Close Hole Tape.
wg
Perform the Flange Back Adjustment after it assembled the Optics Unit.
Close Hole Tape
wa
With four bosses fitted in position, install Zoom Gear Block.
ws
Tighten one screw.
*
*
Tightening torque = 0.068
±
0.01N
•
m (0.7
±
0.1kgf
•
cm)
Front Side
Rear Side
Screw
Zoom Gear Block
Bosses
Spring
Bosses
Tweezers
Ver. 1.2 2010.01
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
2-16
DSC-WX1_L2
2-6. FINAL INSPECTION
2-6-1. Confirm There Is No Fault In Actual Motion/Actual Screen
Inspect it as follows when you exchange parts in the lens block.
1
1
Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
2
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
4
Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
Scratches or stains must not be noticeable, except that the customer permits them.
5
Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
The lens condition must not be worse than that when the camera was received from the customer.
Lens at TELE end
Lens at WIDE end
Upward
Downward
Horizontal
Upper oblique 45˚
Lower oblique 45˚
Full stroke check
Click on the first or last page to see other DSC-WX1 (serv.man3) service manuals if exist.