DOWNLOAD Sony DSC-WX1 (serv.man3) Service Manual ↓ Size: 6.98 MB | Pages: 71 in PDF or view online for FREE

Model
DSC-WX1 (serv.man3)
Pages
71
Size
6.98 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
dsc-wx1-sm3.pdf
Date

Sony DSC-WX1 (serv.man3) Service Manual ▷ View online

1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-WX1_L2
1-5-3. Self-diagnosis Code Table
C
C
E
E
E
E
E
E
E
E
E
Block
Function
1
3
3
2
6
1
6
1
6
2
6
2
6
2
6
2
6
2
9
1
9
2
Detailed
Code
0
1
0
1
0
0
1
0
0
2
1
0
1
1
1
2
2
0
0
1
0
0
Symptom/State
The internal memory has experienced a
 media error.
The internal memory has experienced a
format error.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” type error
The camera cannot read or write data
on the “Memory Stick Duo”.
Trouble with hardware
Difficult to adjust focus
(Cannot initialize focus)
Zoom operations fault
(Cannot initialize zoom lens.)
Abnormality of IC for steadyshot.
Lens initializing failure.
Lens overheating (PITCH).
Lens overheating (YAW).
Abnormality of thermistor.
Abnormality when flash is being charged.
Non-standard battery is used.
Self-diagnosis Code
Repaired b
y:
Correction
Turn the power off and on again.
Format the internal memory.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a supported “Memory Stick Duo”.
Turn the power off and on again, or taking out and inserting the
“Memory Stick Duo” several times.
Turn the power off and on again.
Retry turn the power on by the power switch. If it does not
recover, check the focus reset sensor of lens block (pin rf of
CN401 on the SY-233 board). If it is OK, check the focus motor
drive IC (IC402 on the SY-233 board).
Retry turn the power on by the power switch. Check the zoom
reset sensor of lens block (pin ra of CN401 on the SY-233
board), if zooming is performed when the zoom lever is
operated. If it is OK, check the zoom motor drive IC (IC402 on
the SY-233 board).
Check or replacement of the IC for steadyshot (IC402 on the SY-
233 board).
Check or replacement of the IC for steadyshot (IC402 on the SY-
233 board).
Check the HALL element (PITCH) of optical image stabilizer
(pin qf, qh of CN401 on the SY-233 board). If it is OK, check
PITCH/YAW angular velocity sensor (SE403 on the SY-233
board) peripheral circuits.
Check the HALL element (YAW) of optical image stabilizer (pin
qj
, ql of CN401 on the SY-233 board). If it is OK, check
PITCH/YAW angular velocity sensor (SE403 on the SY-233
board) peripheral circuits.
Check the OIS temp sensor of optical image stabilizer (pin qa,
qs
 of CN401 on the SY-233 board).
Checking of ST-221 board or replacement of ST-221 board.
(Note)
Use the compatible battery only.
Note:
After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.
1-6
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-WX1_L2
Initializes the setting to the default setting.
Even if you execute this function, the images are retained.
1 MENU U 
 (Settings) U 
 (Main Settings) U [Initialize] U [OK]
U [ on the control button
• Be sure not to turn off the camera while initializing.
Note
1-6. PROCESS  AFTER  FIXING  FLASH  ERROR
When “FLASH error”  (Self-diagnosis Code  E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.
Method for Initializing the Flash Error Code
1-7
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-WX1_L2
1. SERVICE  NOTE
1-1. SY-233基板交換時の注意
リストアデータ
補修用基板と交換する時,交換前の基板より調整に必要となるデータを取得してください。
データの取得はAdjust StationからAdjust Manualを起動させて「Restore Data」を実行させてください。
本機で取得されるデータは下記になります。
• USB Serial No.
• Angular Velocity Sensor Sensitivity Adjustment (Dp/Dy Data)
Note:交換前の基板よりデータが読み取れない場合は,SY-233基板とレンズを同時に交換する必要があります。
仕向けデータ
補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
Adjust StationからAdjust Manualを起動させて「Destination Data Write」を実行させてください。
USBシリアルNo.
セットは,1台毎に異なる固有のID(USB Serial No.)を書き込んだ後,出荷されています。
新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。
Adjust StationからAdjust Manualを起動させて「USB Serial No. Input」を実行させてください。
角速度センサ
補修用基板と交換する時,角速度センサ(SE403)の感度表示を書き留めてください
Adjust StationからAdjust Manualを起動させて「Angular Velocity Sensor Sensitivity Adjustment」を実行させて書き留めたデータ
を入力してください。
1-2. レンズ交換時の注意
Note:PITCH/YAWデータは補修用部品にのみ記載されています。
SY-233 BOARD (SIDE A)
SE403
PPP
YYY
PPP : PITCH sensor sensitivity
YYY : YAW sensor sensitivity
1.
レンズにAF-122基板が半田付けされています。
レンズ交換時には,AF-122基板を載せ替えてください。
2.
レンズ交換時,補修用レンズ添付データシート掲載のPITCH/YAWデータを書き留めてください。
Adjust StationからAdjust Manualを起動させて「Angular velocity sensor sensiticvity adj.」を実行させてください。
Note:SY-233基板のSE403感度表示は補修用基板にしか記載されておりません。
P.PP/Y.YY
PITCH/YAW Data
P.PP / Y.YY
YAW Data
PITCH Data
1-8
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-WX1_L2
1-3. 内蔵メモリーのデータコピーおよび消去方法
内蔵メモリーのデータコピーまたは消去はホーム画面の操作から実行可能です。(消去する場合は内蔵メモリーの初期化を
行います。)
Note 1: SY-233基板交換の際は,基板交換前に内蔵メモリーのデータを消去して下さい。
Note 2: SY-233基板交換の際は,基板交換後に内蔵メモリーのフォーマットおよび初期化を実行して下さい。
内蔵メモリーのコピー方法
内蔵メモリーに記録した画像を、
“メモリースティック デュオ”に一括コピーします。
1
充分な空き容量のある“メモリースティック デュオ”を本機に入れる
2 MENU
(設定)
(“メモリースティック”ツール) [コピー]
[実行]
コントロールボタン中央の
ご注意
充分に充電したバッテリーをご使用ください。残量の少ないバッテリーを使用して画像ファイルを
コピーすると、バッテリー切れのためデータを転送できなかったり、データを破損するおそれがあり
ます。
画像ごとのコピーはできません。
データをコピーしても、内蔵メモリー内のデータは削除されません。内蔵メモリーの内容を消去す
るには、コピー後に“メモリースティック デュオ”を本体から取りはずし、
[内蔵メモリーツール]の
[フォーマット]を行ってください。
データをコピーすると“メモリースティック デュオ”内に新しいフォルダが作成されます。コピー先
のフォルダを指定することはできません。
“メモリースティック デュオ”または内蔵メモリーをフォーマット(初期化)します。
市販の“メモリースティック デュオ”はフォーマット済みのため、フォーマットの必要
はありません。
1 MENU
(設定)
(“メモリースティック”ツール)または (内
蔵メモリーツール)
[フォーマット]
[実行]
コントロールボ
タン中央の
ご注意
フォーマットすると、プロテクトしてある画像も含めて、すべてのデータが消去され、元に戻せませ
ん。
内蔵メモリーのフォーマット方法
Page of 71
Display

Click on the first or last page to see other DSC-WX1 (serv.man3) service manuals if exist.