Sony DSC-WX1 (serv.man3) Service Manual ▷ View online
2-1
DSC-WX1_L2
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor (C901) is charged up to the maximum
300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
Short-circuit between two points
with the short jig about 10 seconds.
C901
ST-221 Board
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
1 k
Ω
/1 W
Wrap insulating tape.
2-2
DSC-WX1_L2
2-1. IDENTIFYING PARTS
LCD Block
Main Frame
Tripod Nut
Lens Block
⋅
AF-122 Board
⋅
CD-764 Board
BT Holder Block
⋅
FP-1145 Flexible Board
Cabinet (Upper) Block
⋅
ST-221 Board
2-2-1. CABINET (REAR) SECTION
⋅
Cabinet (Rear)
⋅
Cabinet (L)
⋅
Strap Bracket
2-2-2. FRONT/LCD SECTION
⋅
Control Switch Block (SW61330)
⋅
LCD Block
⋅
Cabinet (Front)
2-2-3. BT HOLDER SECTION
⋅
Cabinet (Upper) Block
⋅
Lens Block
⋅
SY-233 Board
- DISASSEMBLY FLOW -
Cabinet (Rear)
Strap Bracket
Cabinet (L)
Cabinet (G)
Control Switch Block
(SW61330)
(SW61330)
Cabinet (Front)
MC-200 Flexible Board
SY-233 Board
2-3
DSC-WX1_L2
2-2. DISASSEMBLY
2-2-1. CABINET (REAR) SECTION
Follow the disassembly in the numerical order given.
1
Cabinet (Rear) (
1
-1 to
1
-3)
2
Cabinet (L) (
2
-1)
3
Strap Bracket (
3
-1 to
3
-2)
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
1
Cabinet (Rear)
3
Strap Bracket
1
-2
(#170/#171)
1
-1
(#170/#171)
1
-3E
(#170)
2
-1E (Claw)
2
Cabinet (L)
Front/LCD Section
(See Page 2-4)
3
-2E
3
-1
(Claw)
2-4
DSC-WX1_L2
1
-1 (Boss)
1
-3
(Boss)
1
-2 (Boss)
1
-4 (Claw)
1
-5E
1
Control Switch Block
(SW61330)
(SW61330)
2
-4E (Claw)
2
-3 (Slide)
2
-1
2
-2
2
LCD Block
BT Holder Section
(See Page 2-5)
3
Cabinet (Front)
3
-2 (#44)
3
-1 (#170/#171)
3
-5 (Open)
3
-3
3
-4
3
-6E (Open)
Note: DC Cover must open when
you install Front Panel.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
Short-circuit between two points
with the short jig about 10 seconds.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
C901
ST-221 Board
2-2-2. FRONT/LCD SECTION
Follow the disassembly in the numerical order given.
1
Control Switch Block (SW61330) (
1
-1 to
1
-5)
2
LCD Block (
2
-1 to
2
-4)
3
Cabinet (Front) (
3
-1 to
3
-6)
EXPLODED VIEW
HARDWARE LIST
Click on the first or last page to see other DSC-WX1 (serv.man3) service manuals if exist.