DOWNLOAD Sony DSC-RX1RM2 (serv.man2) Service Manual ↓ Size: 13.4 MB | Pages: 126 in PDF or view online for FREE

When replacing the LSV-1601A device, it is need to select the shim thickness.
After selecting the shim thickness, perform one adjustment for lens and imager.

Select the shim thickness

Shim Selection Tool Ver_[][].exe

Adjustment flow

AF defocus shooting mode 

setting

FocusBracket_11.exe

Shim thick replacement

Shim change by according to 

the instructions of the judgment tool

Resolution check 

judgment tool

Resolution Check Tool.exe

OK

NG

Defocus shooting

After half-depressing 

the release button, capture

→Get images one to eleven

Shooting image analysis

RACS.exe

AF defocus shooting mode 

setting release

FocusBracket_Off.exe

1.

Read the following value from the Lens data carry QR seal and then write it.

Lens data carry QR seal

Lens data carry QR seal
(Describing lens tilting amount)

00000014

-14.77   10.30

DSC-RX1RM2

2-9

2.

Select DSC-RX1RM2 from pull-down menu, and start "Shim Selection Tool Ver_[].[]exe".
Enter each recorded value into "Shim Selection Tool Ver_[].[].exe" according to the figure below, and then click
[OK].

Get "Shim Selection Tool Ver_[].[].exe" from each HQ.

Lens data carry QR seal

00000014

-14.77   10.30

3.

The thicknesses of the shims to be used are displayed on the screen.

DSC-RX1RM2

2-10

4.

Select shims that correspond to the displayed thicknesses from following table.

4-443-059-31

0.18 ± 0.005

4-443-059-41

0.20 ± 0.005

4-443-059-51

0.22 ± 0.005

4-443-059-61

0.24 ± 0.005

4-443-059-71

0.26 ± 0.005

4-443-059-81

0.28 ± 0.005

4-443-059-91

0.30 ± 0.005

4-443-060-01

0.32 ± 0.005

4-443-060-11

0.34 ± 0.005

4-443-060-21

0.36 ± 0.005

4-443-060-31

0.38 ± 0.005

4-443-060-41

0.40 ± 0.005

4-443-060-51

0.42 ± 0.005

4-443-060-61

0.44 ± 0.005

4-443-060-71

0.46 ± 0.005

4-443-060-81

0.48 ± 0.005

4-443-060-91

0.50 ± 0.005

4-443-061-01

0.52 ± 0.005

4-443-061-11

0.54 ± 0.005

5.

Install the imager.

6.

After assembling the unit, perform Defocus shooting with resolution chart (J-6082-781-A).

• Get "Resolution Check Tool" from each HQ.
• Before shooting, set the unit to AF Defocus shooting mode.
• After shooting Defocus, release AF Defocus shooting mode.

DSC-RX1RM2

2-11

7.

Start up “RACS.exe” and perform resolution check.
(1) Input the serial number of target unit and click [START].
(2) Drag and drop JPG file of the shot images (eleven) and the analysis is started.
(3) Analysis result is stored as txt file.

If analysis result is no good, perform shooting the chart again.

8.

Start “Resolution Check Tool.exe”.

9.

Select the shim thickness which is currently being used.

10. Select the serial number that is input at RACS and click [3.MTF JUDGE].

DSC-RX1RM2

2-12