DOWNLOAD Sony DSC-P71 / DSC-P71M (serv.man2) Service Manual ↓ Size: 6.79 MB | Pages: 127 in PDF or view online for FREE

Check the deviation of optical axis of AF illuminator.

Mode

CAMERA

Subject

Flash adjustment box (Note 3)
(50 cm or 1 m from the front of
lens)

Measurement Point

Check operation on monitor TV

Measuring Instrument

Perform checking by making the shooting surface of the
Flash adjustment box perpendicular to the optical axis of
the camera.

Perform this checking in the Flash adjustment box.
Restrict external light to enter the Flash adjustment box
as less as possible.

Refer to “4. Preparing the Flash adjustment box”.
(See page 5-7)

Preparation
1) Take a reduced or enlarged copy on the clear sheet so that a

rectangular frame of the sheet for auxiliary light is suitable for
the effective image size of the monitor.

2) Stick the copied sheet for auxiliary light on the monitor screen.

Order Page Address Data

Procedure

1

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-13)

2

9

A9

06/04 Press PAUSE button.

(50 cm/1 m)

3

6

01

EF

Press PAUSE button.

4

6

02

Check the data changes to
“01”.

5

F

10

Check that the data is “00”

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

Release the data setting
performed at step 1. (Refer to
page 5-13)

Before perform the camera system adjustments, check that the
specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat-
isfied.

Taken an extreme care not to destroy the liquid crystal
display module by static electricity when replacing it.

Set the LCD BRIGHTENSS (SET UP setting) to the
NORMAL.

Most of the measuring points for adjusting the LCD system are
concentrated in CN 903 of the PK-064 board.
Connect the Measuring Instruments via the CPC-9 jig (J-6082-
393-C).
The following table shows the Pin No. and signal name of CN
903.

Pin No.

Signal Name

Pin No.

Signal Name

1

BL_L1

10

UNREG

2

CVCHK OUT

11

LANC IN

3

N. C.

12

LANC OUT

4

REG_GND

13

MAKER_RECOG

5

CPC_IN

14

N. C.

6

BL_L2

15

N. C.

7

HSY

16

N. C.

8

PANEL_COM

17

N. C.

9

VG

18

N. C.

CPC lid

PK-064 board
CN903

CPC-9 jig
(J-6082-393-C)
(Note 1, 2)

1

18

Note 1: Don’t use the 12 pin flexible board of CPC-9 jig.

It causes damage to the unit.

Note 2: The old CPC-9 jig (Parts code: J-6082-393-B)

cannot be used, because it cannot operate
the adjusting remote commander.

Mode

PLAY

Signal

Arbitrary

Adjustment Page

A

Adjustment Address

62, 63, 80 to 8F, A3, A4

Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, and enter the data given in the following table.

Press the PAUSE button each time the data are set, as the
data are written to non-volatile memory (EEPROM).

Address

Data

Remark

62

9A

Fixed value

63

66

80

8E

Backlight current adj.(BL L)

81

36

Backlight current adj.(BL H)

82

5E

VCO adj. (NTSC)

83

7C

VCO adj. (PAL)

84

A9

V-COM DC adj.

85

9B

D Range adj.

86

0A

Black Limit adj

87

3A

Psig Gray adj.

88

90

White Blance adj.

89

83

8A

4C

Contrast adj.

8B

48

Center voltage adj.

8C

2F

8D

11

8E

16

Fixed value

8F

1F

A3

28

A4

04

Processing after Completing Adjustments:
1) Select page: 0, address: 01, and set data: 00.

Mode

PLAY

Signal

Arbitrary

Adjustment Page

B

Adjustment Address

3A to 3F

Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: B, and enter the data given in the following table.

Press the PAUSE button each time the data are set, as the
data are written to non-volatile memory (EEPROM).

Address

Data

Remark

3A

57

3B

FE

3C

02

Fixed data

3D

5A

3E

00

3F

01

Processing after Completing Adjustments:
1) Select page: 0, address: 01, and set data: 00.

Adjust electric current value of backlight in two modes.

Mode

PLAY

Signal

Arbitrary

Measurement Point

Pin 6 of CN903 (BL-L2)
Pin 1 of CN903 (BL-L1)

Measuring Instrument

Digital voltmeter

Adjustment Page

A

Adjustment Address

80, 81

Specified Value

L = 0.408 

± 0.004 Vp-p

H = 0.748 

± 0.004 Vp-p

Order Page Address Data

Procedure

1

0

01

01

2

A

80

Change the data and set the
voltage (L) to the specified
value.

3

A

80

Press PAUSE button.

4

A

81

Change the data and set the
voltage (H) to the specified
value.

5

A

81

Press PAUSE button.

Order Page Address Data

Procedure

1

0

01

00

Set the VCO free-run frequency. If deviated, the LCD screen will
be blurred.

Mode

PLAY

Signal

Arbitrary

Measurement Point

Pin 7 of CN903 (HSY)

Measuring Instrument

Frequency counter

Adjustment Page

A

Adjustment Address

82 (NTSC)
83 (PAL)

Specified Value

T = 15734 

± 30 Hz (NTSC)

T = 15625 

± 30 Hz (PAL)

Menu setting:
1) VIDEO OUT of SET UP setting

.................................. NTSC (NTSC mode)

(This adjustment must be performed in NTSC mode, so don’t
set the menu setting to “PAL” )

Order Page Address Data

Procedure

1

0

01

01

2

4

F1

13

(NTSC)

3

4

1D

82

(PAL)

Change the data and set the

4

A

82

frequency (f) to the
NTSC specified value.

5

A

82

Press PAUSE button.

Change the data and set the

6

A

83

frequency (f) to the
PAL specified value.

7

A

83

Press PAUSE button.

Order Page Address Data

Procedure

1

4

F1

00

(NTSC)

2

4

1D

80

(PAL)

3

0

01

00