DOWNLOAD Sony DSC-P71 / DSC-P71M (serv.man2) Service Manual ↓ Size: 6.79 MB | Pages: 127 in PDF or view online for FREE

Adjust the sync level of the composite video signal output and
check the burst level of the composite video signal output.

Mode

PLAY

Signal

Arbitrary

Measurement Point

Video terminal of VIDEO OUT
jack (75 

Ω terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

A

Adjustment Address

A0

Specified Value

Sync level:
  A = 286 

± 5 mV (NTSC)

  A = 300 

± 5 mV (PAL)

Burst level:
  B = 286 

± 10 mV (NTSC)

  B = 300 

± 30 mV (PAL)

Order Page Address Data

Procedure

1

0

01

01

2

A

02

03

3

4

F1

04

4

A

A0

Change the data and set the
sync level (A) to the specified
value.

5

A

A0

Press PAUSE button.

6

Check the burst level (B) to the
specified value.

Order Page Address Data

Procedure

1

4

F1

00

2

0

01

00

A

B

H

Before perform the camera system adjustments, check that the
specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat-
isfied.

For “CAMERA SYSTEM ADJUSTMENTS”, perform in
order of item numbers.

Perform the following data setting before the camera system ad-
justments.
It is not necessary to perform the following data setting everytime
when you perform some items of camera system adjustments con-
tinuously unless the power is turned off. Only when the power is
turned off during this adjustments, perform the data setting again,
then continue the adjustments.

Set up setting:
1) VIDEO OUT of SET UP setting............... NTSC (NTSC mode)

(This adjustment must be performed in NTSC mode, so don't
set the SET UP setting to “PAL”)

Order Page Address Data

Procedure

1

0

01

01

2

A

01

Set the bit value of bit 5 is
“1”, and press PAUSE
button. (Note 1)

3

2

10

Check the bit values of bit3,
bit4 and bit5 are “1”.
(Note 1, 2)

4

A

00

Set the bit value of bit 1 is
“1”, and press PAUSE
button. (Note 1)

5

A

02

Set the bit value of bit 1 is
“1”, and press PAUSE
button. (Note 1)

6

D

21

04

Press PAUSE button.

7

6

C1

Check the data changes to
“02”.

8

6

6C

01

9

Wait for 1 second.

10

E

96

00

Press PAUSE button.

: For the bit values, refer to “5-2. SERVICE MODE”,

“2-3. 2. Bit value discrimination”.

In case of wrong data.
• Select page: 2, address: 00 and set data: 29.
• Select page: 2, address: 01 and set data: 29.
• Select page: 2, address: 0C, set the bit value of bit 1 is

1.

• Select page: 2, address: 04 and set data: 04.

Set the adjusting remote commander to normal LANC,
and the power will be turned, off and on automatically.

Repeat the “Data setting method”, if the power was turned
off and on during the “CAMERA SYSTEM ADJUST-
MENTS”.

Order Page Address Data

Procedure

1

E

96

40

2

6

6C

00

3

D

21

00

Press PAUSE button.

4

A

02

Set the bit value of bit 1 is
“0”, and press PAUSE
button. (Note 1)

5

A

00

Set the bit value of bit 1 is
“0”, and press PAUSE
button. (Note 1)

6

A

01

Set the bit value of bit 5 is
“0”, and press PAUSE
button. (Note 1)

7

0

01

00

Mode

CAMERA

Subject

Color bar chart
(Standard picture frame with the
zoom lens at WIDE end)

Measurement Point

Video terminal of VIDEO OUT
jack (75 

Ω terminated)

Measuring Instrument

Oscilloscope and monitor TV

Specified Value

A=B, C=D, E=F

Displayed data of the page 1 of adjusting remote com-
mander.

1:XX:XX

YL data
YH data

Switch setting
1) FOCUS (Menu setting) .............................. MULTI AF
2) MACRO (Control button) .......................... ON

Order Page Address Data

Procedure

1

Shoot the color bar chart
with the zoom WIDE end.

2

Enter the output of VIDEO
OUT to the monitor TV, and
move the position as shown
in Fig. 5-1-14.

3

Horizontal width of one color
(B, C) and that of black (A,
D) on the color bar chart
should be same. (See Fig. 5-
1-12)

4

With vertical width of black
(E, F) set in same, the color
bar chart should come to the
center of monitor TV. (See
Fig. 5-1-13)

5

Check that the color bar on
the monitor TV is focused.

6

0

03

22

7

1

Note down the YH and YL
data. (Note 1)

Order Page Address Data

Procedure

1

0

03

00

Order Page Address Data

Procedure

1

6

2C

01

2

6

90

00

3

6

91

00

4

6

92

YL

(Note 2)

5

6

93

YH

(Note 2)

6

6

01

79

Press PAUSE button.

7

6

07

Check the data changes to
“01”.

8

6

01

00

Press PAUSE button.

The data noted down at step 7 of “Setting method”.

A=B

C=D

A

B

C

D

Color bar chart picture frame

Monitor TV picture frame

E=F

V

E

F

The inner focus lens flange back adjustment is carried out auto-
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.

Mode

CAMERA

Subject

Siemens star chart with ND filter
for minipattern box (Note 1)

Measurement Point

Check operation on monitor TV

Measuring Instrument

Adjustment Page

F

Adjustment Address

18 to 3E, 52, 53

Dark Siemens star chart.

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Preparations before adjustments:
1) The minipattern box is installed as shown in the following fig-

ure.

 The attachment lenses are not used.

2) Install the minipattern box so that the distance between it and

the front of lens of camera is less than 3 cm.

3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the

specified voltage 

± 0.01 Vdc.

5) Check that the center of Siemens star chart meets the center of

shot image screen with the zoom lens at TELE end and WIDE
end respectively.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjustment the power sup-
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the mini-
pattern box.

Minipattern box

Below 3 cm

Camera

Camera 

table

Red (+)

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Regulated power supply

Output voltage : Specified voltage 

±

 0.01 Vdc

Output current : more than 3.5 A

Order Page Address Data

Procedure

1

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-13)

2

6

01

13

Press PAUSE button.

3

6

01

27

Press PAUSE button.
(Note 4)

4

6

02

Check the data changes to
“01”.

5

F

3E

Check the data.
00: Normal
01 to FF: Defective

6

F

24

Check the data.
0A to 7F: Normal
00 to 09,
80 to FF: Defective

The adjustment data will be automatically input to page:
F, address: 18 to 3E, 52 and 53.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

Release the data setting
performed at step 1.
(Refer to page 5-13)

3

Perform “Flange Back
Check”.