Sony XAV-W600 / XAV-W650BT Service Manual ▷ View online
XAV-W600/W650BT
21
3-3. FRONT PANEL BLOCK
1 screw
(PTT2.6
(PTT2.6
u 5)
1 screw
(PTT2.6
(PTT2.6
u 5)
2 claw
1 two screws
(PTT2.6
(PTT2.6
u 5)
2 claw
2 two
claws
claws
9 front panel block
4 sheet
(KEY
(KEY
protection)
2 claw
5 flexible flat
cable
cable
7 BT ANT
connector
connector
6 filament tape
(sub
(sub
material)
8 Remove the BT ANT clamp
from the groove.
Note 2: When installing the flexible
flat cable, align the position
of the boundary line of the
blue area and the white line
of the KEY board.
Insert is fully.
Insert is incomplete.
Tightly paste.
Loosely paste.
BT ANT
connector
connector
BT ANT
clamp
clamp
filament tape
(sub material)
(sub material)
BT board
OK
NG
OK
NG
touch panel flexible board
Note 1: Arrange the touch panel flexible
board as shown in the figure
below before installing the sheet
(key
protection).
KEY board
–
Right view
–
BT ANT wire setting
+Rw tR instDOO the IOe[iEOe
IODt FDEOe
IODt FDEOe
white line
+Rw tR instDOO the sheet Ne\ SrRteFtiRn
3 Remove the front panel block
in the direction of the arrow.
groove
:BT
XAV-W600/W650BT
22
3-4. DVD DECK ASSY (DR28N-ABB-YG) (DVM1)
3-5. GUIDE ASSY, BT ANT (ANT1) (W650BT)
1 two screws
(PTT2.6
(PTT2.6
u 5)
1 screw
(PTT2.6
(PTT2.6
u 5)
2 Lift up the
DVD
deck assy
(DR28N-ABB-YG)
(DVM1)
in the direction of the arrow.
4
DVD
deck assy
(DR28N-ABB-YG)
(DVM1)
3 flexible flat cable
Connector is unlocked.
Insert is straight to the interior.
Note: When installing the flexible flat cable,
insert straight to the connector and lock a
connector
completely.
No slanting after insertion.
OK
NG
BT ANT clamp
4 Remove the BT
ANT clamp from
the
groove.
groove
–
Front panel block rear view
–
1 screw
(B2
(B2
u 8)
5 BT ANT (ANT1)
BT ANT (ANT1)
2 two screws
(B
(B
M2
u 3.5)
3 guide assy
Wire setting
groove
BT ANT clamp
(W650BT)
(W650BT)
XAV-W600/W650BT
23
3-6. VOL KNOB ASSY, KEY BOARD, FRONT PANEL ASSY (FP1)
–
Front panel block rear view
–
5 screw
(K
M2
u 3.5)
5 screw
(K
M2
u 3.5)
5 two screws
(K
M2
u 3.5)
7 claw
8 Draw the wire out from the hole
of the KEY board.
7 four claws
1 VOL knob assy
3 touch panel flexible board
4 LCD flexible board
6 screw
(B2
u 8)
6 screw
(B2
u 8)
2 connector
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
How to install the flexible flat cable
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
KEY board
E7
Insert is shallow
Insert is straight
to the interior.
to the interior.
Note 2: When installing the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
Wire setting
OK
NG
hole
9 KEY board
6 screw
(B2
u 8)
0 front panel assy (FP1)
Note 1:
When the VOL knob assy is replaced, Bluetooth information
writing is necessary. Refer to “BLUETOOTH INFORMA-
TION WRITING METHOD” on page 7. (XAV-W650BT
only)
writing is necessary. Refer to “BLUETOOTH INFORMA-
TION WRITING METHOD” on page 7. (XAV-W650BT
only)
Note 3:
When the KEY board and front panel assy are replaced, refer
to “FLICKER ADJUSTMENT” on page 25.
to “FLICKER ADJUSTMENT” on page 25.
XAV-W600/W650BT
24
3-7. BT MIC (CABLE) (BTM1) (W650BT)
1 Remove the BT MIC cable
from two lead pins.
4 BT MIC (cable)
(BTM1)
(BTM1)
groove
3 Remove the clamp from the groove.
Note: When installing the BT
Note: When installing the BT
MIC (cable), check that
clamp is not damaged.
–
Rear view
–
%7 0,& FaEOe VeWWiQJ
clamp
two lead pins
MAIN board
BT board
connector
BT MIC (cable)
(BTM1)
(BTM1)
front side
rear side
clamp
front side
rear side
2 BT MIC cable
connector
BT board
3-8. BT BOARD (W650BT)
5 Remove the BT board
in the direction of the
arrow.
2 connector
1 Remove the wire
from two hooks.
:LUHVHWWLQJ
MAIN board
BT board
two hooks
3 Remove two solders.
4 Bent claw is returned
to a straight form.
4 Bent claw is returned
to a straight form.
–
5HDUYLHZ
–
front side
rear side
6 BT board
Note 1:
When the BT board is replaced, be sure to replace the VOL
knob assy simultaneously.
knob assy simultaneously.
Note 2:
When the BT board is replaced, Bluetooth information writ-
ing is necessary. Refer to “BLUETOOTH INFORMATION
WRITING METHOD” on page 7.
ing is necessary. Refer to “BLUETOOTH INFORMATION
WRITING METHOD” on page 7.
Note 3:
When the BT board is replaced, replaced old BT board is de-
stroyed with the hammer, and throw out it.
stroyed with the hammer, and throw out it.
Click on the first or last page to see other XAV-W600 / XAV-W650BT service manuals if exist.