DOWNLOAD Sony XAV-W600 / XAV-W650BT Service Manual ↓ Size: 2.78 MB | Pages: 30 in PDF or view online for FREE

DESTINATION  SETTING  METHOD
When the chassis main assy (CHA1) is replaced, the destination 
setting is necessary.

 Remote commander is necessary.

 

    It is necessary to operate by the remote commander, even in case of 

models that have not been supplied the remote commander.

  

 

(Refer 

to 

“ACCESSORIES” on page 28 about the remote com-

mander)

 It is not necessary for US, Canadian and MARUTI SUZUKI mod-

els to perform the destination setting. Check whether correct des-
tination is set, refer to “Destination setting checking method” on 
page 6. If correct destination is not set, perform the destination 
setting according to the following procedure.

  

 

(When 

correct 

destination has been set for MARUTI SUZUKI  

model, “MURUTI SUZUKI” screen is displayed on the screen at 
startup. (Refer to Note in the “MODEL IDENTIFICATION” on 
page 4))

1.  Preparing the Destination Setting
Be sure to solder the SL001 on the MAIN board before doing the 
destination setting.

Set destination according to the procedure below.

2-1.  Setting the Destination Code
1.  Turn the power on this unit.
2.  Press the [OFF] button on the remote commander.
3.  In the state of source off (Home screen is displayed), enter the 

destination setting mode by pressing the buttons on the remote 
commander in order of the [4] t [5] t [6] (press only the [6] 

button for two seconds).

4.  The following screen is displayed and the destination setting 

mode becomes effective.

 

(Displayed characters/values in the following fi gure  are  ex-
ample)

 Refer to following “2-2. Entering the Destination Code” for opera-

tion method.

<DESTINATION SETTING MODE>

0

  0   0   0   0   0

E U R :   0 0 0 0 0 0

E 1 7 :   0 0 0 0 1 2

R U 2 :   0 0 0 0 0 4

E A :   0 0 0 0 1 A

U C :   0 0 0 0 0 1

E :   0 0 0 0 0 3

I N 3 :   0 0 0 0 1 6

E T 4 :   0 0 0 0 1 C

5.  The resetting operation is executed by pressing the reset button  

after the setting ends, and the unit returns to the normal condi-
tion.

 Input of the destination code cannot be performed by the keys of 

main unit. Be sure to input the destination code by remote com-
mander.

 The model to which the remote commander is not attached can 

also be operated by using the remote commander.

 The number buttons on the remote commander cannot be used.

1. Press the [V] or [v] button, and select the alphanumeric char-

acter of “0 to F”.

2.  The digit advances by pressing the [b] button.

 

The digit returns by pressing the [B] button.

3.  The setting is completed by pressing the [ENTER] button, and 

the initialization operation is done.

AEP and UK models (EUR)

000000

US and Canadian models (UC)

000001

E (NTSC) model (E)

000003

Russian model (RU2)

000004

E (PAL) model (E17)

000012

Indian model (IN)

000015

MARUTI SUZUKI model (IN3)

000016

Saudi Arabia model (EA)

00001A

Australian model (ET4)

00001C

– Continued on next page –

3.  Processing  After the Destination Setting
Be sure to unsolder the SL001 on the MAIN board after doing the 
destination setting.

Be sure to unsoleder the SL001 on the MAIN board.

If you do not unsolder, this unit is not operated correctly.

4. Confi rmation After Destination Setting
Execute the following operation after completing the destination 
setting, and confi rm a correct destination was set.

Destination setting checking method:
1.  Press the reset button on the main unit.

2.  Press the [OFF] button on the remote commander.
3.  In the state of source off (Home screen is displayed), enter the 

test mode by pressing the buttons on the remote commander in 
order of the [4] t [5] t [0] (press only the [0] button for two 

seconds).

4.  The following screen is displayed and confi rm that item of the 

destination has been rewritten correctly.

 

(Displayed characters/values in the following fi gure are ex-
ample)

<Test Mode>

  1.AUDIO FACTORY MODE

  2.AUDIO DEBUG MODE

  4.VISUAL FACTORY MODE

  6.DESTINATION SETTING MODE

DEST: EUR                      REGION: 2
MCU: SONY-ST06-150721
Graphic: SONY-TW06-150721
Mecha: SONY-SP02-150721
Servo: HI6CD1-BBA-893D
BT: H28004-V2R133-20001 / XAV-W650BT
BT Addr: 001753767368

5.  The resetting operation is executed by pressing the reset button 

after the confi rming ends, and the unit returns to the normal 
condition.

BLUETOOTH  INFORMATION  WRITING  METHOD
(XAV-W650BT only)
When the complete BT board or VOL knob assy is replaced, it is 
necessary to write the Bluetooth information (address).
Write the Bluetooth information (address) according to the proce-
dure below.
Confi rm the tool used in this work to the service headquarters.

 It is unnecessary for XAV-W600 to perform this work for NFC non-

compatible.

Preparation:
• Windows 

PC

•  NFC compatible smartphone that installed the fi le manager ap-

plication (ASTRO File Manager, File Expert, etc.)

•  USB cable for the smartphone
• 15Visual_NFCtagWriter_v120.apk

Install the 15Visual_NFCtagWriter_v120.apk on the smart-
phone for writing of Bluetooth information.

Procedure:
1.  Prepare the 15Visual_NFCtagWriter_v120.apk fi le on the PC.
2.  Connect the smartphone to the PC with the USB cable.
3.  Transfer the 15Visual_NFCtagWriter_v120.apk to the smart-

phone.

4.  When tapping the “Settings” 

→ “Security” on the screen of the 

smartphone, check the box “Unknown sources”.

5.  Disconnect the smartphone from the PC.
6. Use 

the 

fi le manager application to explore the 15Visual_NFC-

tagWriter_v120.apk on the smartphone.

7.  Click on the 15Visual_NFCtagWriter_v120.apk to open it, and 

install the 15Visual_NFCtagWriter_v120.apk to the smartphone.

8.  When tapping the “Settings” 

→ “Security” on the screen of the 

smartphone, uncheck the box “Unknown sources”.

Movies

YouTube

Camera

Settings

Album

WALKMAN

Play Store

Browser

Maps

Media Player

Chrome

15visual

NFCtagWrite

2.  Writing the NFC Tag Data
Write the NFC tag data (Bluetooth information) to the NFC mod-
ule in the VOL knob assy.

Procedure:
1.  In the state of source off (Home screen is displayed), enter the 

test mode by pressing the buttons on the remote commander in 
order of the [4] t [5] t [0] (press only the [0] button for two 

seconds).

2.  The following screen is displayed and confi rm the BT Addr 

(Bluetooth address).

 

(Displayed characters/values in the following fi gure  are  ex-
ample)

<Test Mode>

  1.AUDIO FACTORY MODE

  2.AUDIO DEBUG MODE

  4.VISUAL FACTORY MODE

  6.DESTINATION SETTING MODE

DEST: EUR                      REGION: 2
MCU: SONY-ST06-150721
Graphic: SONY-TW06-150721
Mecha: SONY-SP02-150721
Servo: HI6CD1-BBA-893D
BT: H28004-V2R133-20001 / XAV-W650BT
BT Addr: 001753767368

3.  The resetting operation is executed by pressing the reset button 

after the confi rming ends, and the unit returns to the normal 
condition.

4.  Turn on the NFC function of the smartphone.
5.  Start the 15Visual NFCtagWriter application on the smart-

phone.

6.  Tap the “Write” on the screen of the smartphone.

15Visual NFCtagWriter

15Visual NFCtagWriter

– Continued on next page –

7.  Input the Bluetooth Local Name (BL_NAME).
 

(Input the model name with the keyboard on the smartphone, 
or tap the “List” on the screen of the smartphone and select the 
model name)

Bluetooth Local Name

Bluetooth Device Addres

15Visual NFCtagWriter

8.  Input the Bluetooth address (BD_ADDR).
 

(Input the Bluetooth address (BD_ADDR) that confi rmed on 
the screen in the test mode with the keyboard on the smart-
phone)

Bluetooth Device Addres

XAV-W650BT

15Visual NFCtagWriter

9.  Tap the “Write” on the screen of the smartphone, in the state 

that unchecked the box “Read-only”.

001753767368

XAV-W650BT

15Visual NFCtagWriter

10.  Touch the N-mark part of the smartphone to the N-mark part of 

the unit.

11. Check that “Completed!” is displayed on the screen of the 

smartphone.

 When “Completed!” is not displayed on the screen of the smart-

phone, refer to “3. Error Display” on the page 9.

15Visual NFCtagWriter

12. End the 15Visual NFCtagWriter application on the smart-

phone.

13. Check the operation of connecting with the smartphone by one 

touch (NFC).

 

(Refer to the 

“OPERATION CHECK OF THE NFC AFTER  

COMPLETING THE REPAIRS” on the page 11)

14. Start the 15Visual NFCtagWriter application on the smart-

phone.

15. Tap the “Write” on the screen of the smartphone.

15Visual NFCtagWriter

15Visual NFCtagWriter

16. Check the box “Read-only” on the screen of the smartphone, 

and tap the “Write” on the screen of the smartphone.

001753767368

XAV-W650BT

15Visual NFCtagWriter

– Continued on next page –