Sony CDX-605 / XDC-40 (serv.man2) Service Manual ▷ View online
MICROFILM
SERVICE MANUAL
COMPACT DISC CHANGER
US Model
Model Name Using Similar Mechanism
CDX-505RF
CD Drive Mechanism Type
MG-250C-137
Optical Pick-up Name
KSS-521A/J2N
System
Compact disc digital audio system
Frequency response
10 – 20,000 Hz
Wow and flutter
Below the measurable limit
Signal-to-noise ratio
94 dB
Outputs
BUS control output (8 pins)
Analog audio output (RCA pin)
Analog audio output (RCA pin)
Current drain
800 mA (during CD playback)
800 mA (during loading or ejecting a disc)
800 mA (during loading or ejecting a disc)
Operating temperature
– 10
°
C to + 55
°
C (14
°
F to 131
°
F)
Dimensions
Approx. 262
×
90
×
181.5 mm
(10
3
/
8
×
3
5
/
8
×
7
1
/
4
in.) (w/h/d)
not incl. projecting parts and controls
Mass
Approx. 2.1 kg (4 lb 10 oz)
Power requirement
12 V DC car battery
(negative ground)
(negative ground)
Supplied accessories
Disc magazine (1)
Parts for installation and connections
(1 set)
Parts for installation and connections
(1 set)
Design and specifications subject to change without notice.
SPECIFICATIONS
CDX-605
– 2 –
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED
LINE WITH MARK
!
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
TABLE OF CONTENTS
1.
SERVICING NOTE
...................................................
2
2.
GENERAL
Installation .......................................................................
3
Connections .....................................................................
4
3.
DISASSEMBLY
.........................................................
6
4.
MECHANISMDECK ASSEMBLY
...................... 12
5.
MECHANICAL ADJUSTMENTS
....................... 14
6.
ELECTRICAL ADJUSTMENTS
......................... 15
7.
DIAGRAMS
................................................................. 17
7-1. Notes for Printed Wiring Board and
Schematic Diagram ......................................................... 18
7-2. Printed Wiring Boards – RF Section – .......................... 19
7-3. Schematic Diagram – RF Section – ................................ 21
7-4. Printed Wiring Boards
7-3. Schematic Diagram – RF Section – ................................ 21
7-4. Printed Wiring Boards
– MAIN/JACK BOARD (Component side) – ................ 23
7-5. Printed Wiring Boards
– MAIN/JACK BOARD (Conductor side) – .................. 25
7-6. Schematic Diagram – MAIN Section (1/2) – ................. 27
7-7. Schematic Diagram – MAIN Section (2/2) – ................. 29
7-8. IC Pin Function Description ........................................... 34
7-7. Schematic Diagram – MAIN Section (2/2) – ................. 29
7-8. IC Pin Function Description ........................................... 34
8.
EXPLODED VIEWS
................................................ 36
9.
ELECTRICAL PARTS LIST
............................... 41
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-
UP BLOCK OR BASE UNIT
UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
Laser Diode Properites
• Material: GaAlAs
• Wavelength: 780 nm
• Emission Duration: continuous
• Laser Output Power: less than 44.6 µW*
• Material: GaAlAs
• Wavelength: 780 nm
• Emission Duration: continuous
• Laser Output Power: less than 44.6 µW*
* This output is the value measured at a distance of 200 mm
from the objective lens surface on the Optical Pick-up Block.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
DISC MAGAZINE GETTING OUT PROCEDURE
ON THE POWER SUPPLY IS OFF
ON THE POWER SUPPLY IS OFF
Remove the CASE (LOWER) assembly beforehand
1) Press the lever (stop) assy to arrow direction.
2) Removal the magazine assy.
2) Removal the magazine assy.
Note:
Take out the magazine only when the tray is completely within the
magazine. If the disk or tray is sticking out, turn on the power and
eject the magazine.
eject the magazine.
Magazine ass’y
Lever (stop) ass’y
– 3 –
– 4 –
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
– 5 –
– 6 –
Note:
Follow the disassembly procedure in the numerical order given.
COVER (UPPER T), FRONT PANEL ASS’Y
SECTION 3
DISASSEMBLY
MECHANISM DECK (MG-250C-137)
1
screw
(PTT2.6
(PTT2.6
×
6)
1
screw
(PTT2.6
(PTT2.6
×
6)
2
cover (upper T)
1
screw
(PTT2.6
(PTT2.6
×
6)
1
screw
(PTT2.6
(PTT2.6
×
6)
1
screw
(PTT2.6
(PTT2.6
×
6)
3
lever (FL)
3
lever (FL)
4
front panel ass’y
2
tension spring (FL)
2
tension spring (FL)
1
two dampers (250)
1
two dampers (250)
3
jack flexible board
(CN901)
(CN901)
4
mechanism deck (MG-250C-137)