Sony CDX-605 / XDC-40 (serv.man2) Service Manual ▷ View online
– 11 –
SW BOARD, SPINDLE MOTOR ASS’Y (M101)
CHUCKING MOTOR ASS’Y (M103)
8
two screws
(P1.7
(P1.7
×
2.2)
7
3
spring (chucking)
6
retainer (disc)
4
screw
(P2
(P2
×
2.2)
5
bracket (CP)
9
Remove the spindle motor ass’y (M101)
of the arrow.
of the arrow.
2
SW board
1
screw
(P2
(P2
×
2.2)
2
two screws (P2
×
2.5)
4
chucking motor ass’y
(M103)
(M103)
1
connector
(CNP51)
(CNP51)
3
bracket
(load motor)
(load motor)
– 12 –
Note:
Follow the assembly procedure in the numerical order given.
OPTICAL PICK-UP COMPLETE ASS’Y
GEAR (LOMINI) / (LOAD 1) ASS’Y
SECTION 4
MECHANISM DECK ASSEMBLY
chuck plate
1
Move the lever (LOCK 3) in direction
A
, and return it a little in
direction
B
from the position where the chuck plate is moved
down to the lower limit.
A
B
4
stop ring 2.0 (E type)
5
tension spring (DH)
2
washer 2.5
3
optical pick-up complete ass’y
Note: Insert the shaft (A) first.
Note: Insert the shaft (A) first.
shaft (A)
gear (LOAD 2)
gear (LOMINI)
marking
Fig. A
Fig. A
chuck plate
2
Attach the gear (LOMINI) at the position
shown in Fig. A.
shown in Fig. A.
shaft (rotary prevention C)
1
Move the lever (LOCK 3)
fully in direction
fully in direction
B
to
move the chuck plate up.
B
4
stop ring 1.5 (E type)
3
Attach the gear (LOAD 1) ass’y
with its facing inside.
with its facing inside.
slit
– 13 –
OPERATION CHECK
1
Confirm that the slider moves in direction
C
to move down
the chuck plate if the gear (LOAD 1) is rotated in direction
A
or
the chuck plate moves up and the slider moves in direction
D
if
the gear is rotated in direction
B
.
chuck plate
slider
gear (LOAD 1) ass'y
A
B
C
D
– 14 –
SECTION 5
MECHANICAL ADJUSTMENTS
• Elevator Height (Address) Adjustment
Note:
This adjustments is necessary when the system controller (IC201),
variable resistor (RV201), slider (R), slider (L), or chassis (ELV)
was replaced for any repair.
variable resistor (RV201), slider (R), slider (L), or chassis (ELV)
was replaced for any repair.
Connection:
Adjustment Method:
1. Connect this set to the master unit (e.g. MDX-C670/
1. Connect this set to the master unit (e.g. MDX-C670/
C670RDS), load a disc magazine, and place the set vertically
as shown below.
as shown below.
2. Connect the regulated power supply to the master unit, and
turn the power on.
3. Press the DISC button on the master unit and select DISC 5.
4. At this time, if the elevator shaft does not position between
comb teeth A and B at addresses 5 and 6 as shown below,
adjust the following.
adjust the following.
5. Press repeatedly the DISC + and – buttons on the master unit
so that the elevator shafts moves from address 6 to address 5,
or from 5 to 6. At this time, adjust RV201 on the main board
so that the elevator shaft positions smoothly between comb
teeth A and B.
or from 5 to 6. At this time, adjust RV201 on the main board
so that the elevator shaft positions smoothly between comb
teeth A and B.
6. Further, place the set horizontally and make same adjustment
as mentioned above.
7. After adjustment at addresses 5 to 6 is finished, check all op-
erations from addresses 1 to 10 with the set placed vertically
and horizontally respectively to confirm that the elevator shaft
positions in a range between comb teeth A to B.
and horizontally respectively to confirm that the elevator shaft
positions in a range between comb teeth A to B.
power supply
GND
+
BUS cable
CDX-605
master unit
comb tooth at address 6
elevator shaft
comb tooth at address 6
comb tooth at address 5
RV201
OK
NG
elevator shaft
comb tooth at address 5
A
B
A
B
Click on the first or last page to see other CDX-605 / XDC-40 (serv.man2) service manuals if exist.