Sony STR-DA5300ES Service Manual ▷ View online
5
STR-DA5300ES
6-92. Printed Wiring Board – AC Board (TYPE A) – ............. 124
6-93. Printed Wiring Board – AC Board (TYPE B) – ............. 124
6-94. Schematic Diagram – AC Board – ................................. 125
6-93. Printed Wiring Board – AC Board (TYPE B) – ............. 124
6-94. Schematic Diagram – AC Board – ................................. 125
7.
EXPLODED VIEWS
7-1.
Case Section ................................................................... 173
7-2.
DIGITAL Board Section ................................................ 174
7-3.
D-VIDEO Board Section ................................................ 175
7-4.
DISPLAY Board Section ................................................ 176
7-5.
Front Panel Section ........................................................ 177
7-6.
A-VIDEO Board Section ................................................ 178
7-7.
ANALOG Board Section ............................................... 179
7-8.
Heat Sink Section ........................................................... 180
7-9.
MAIN Board Section ...................................................... 181
8.
ELECTRICAL PARTS LIST
............................... 182
Note 1: Refer “NOTE WHEN THE AC BOARD IS REPAIRED”
(page 5) in servicing notes for how to distinguish TYPE
A/B.
A/B.
Note 2: Refer to SUPPLEMENT-1 for the CONTROL, DIGITAL and
DSP boards of printed wiring boards, schematic diagrams
and electrical parts list of Russian and Ukrainian models.
When repairing the set of US, Canadian, AEP and UK
models, refer to either of original service manual/SUPPLE-
MENT-1 according to the set.
and electrical parts list of Russian and Ukrainian models.
When repairing the set of US, Canadian, AEP and UK
models, refer to either of original service manual/SUPPLE-
MENT-1 according to the set.
Note 3: Refer to SUPPLEMENT-1 for the CONTROL, DIGITAL and
DSP boards of printed wiring boards, schematic diagrams
and electrical parts list of Chinese model.
Refer to SUPPLEMENT-2 for the A-CLASS AMP, D-CON-
NECT and E-VOL boards of printed wiring boards, sche-
matic diagrams and electrical parts list of Chinese model.
When repairing the set except Chinese model, refer to
either of original service manual/SUPPLEMENT-1/
SUPPLEMENT-2 according to the set.
and electrical parts list of Chinese model.
Refer to SUPPLEMENT-2 for the A-CLASS AMP, D-CON-
NECT and E-VOL boards of printed wiring boards, sche-
matic diagrams and electrical parts list of Chinese model.
When repairing the set except Chinese model, refer to
either of original service manual/SUPPLEMENT-1/
SUPPLEMENT-2 according to the set.
Ver. 1.2
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40
°
C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE OF REPLACING THE IC3601 ON THE
D-VIDEO BOARD
D-VIDEO BOARD
Replacement of IC3601 on the D-VIDEO board used in this set
requires a special tool.
requires a special tool.
NOTE WHEN THE AC BOARD IS REPAIRED
(US and Canadian models only)
(US and Canadian models only)
Note:
AEP, Russian, Ukrainian and UK models uses only TYPE B.
Two types exist in the AC board for US and Canadian models.
Repair after distinguishing which type it is referring to the figure
below.
Repair after distinguishing which type it is referring to the figure
below.
– AC Board (Component Side) –
JW003
TYPE A : JW003 is not mounted.
TYPE B : JW003 is mounted.
TYPE B : JW003 is mounted.
6
STR-DA5300ES
•
MODEL IDENTIFICATION
Model
PART No.
US and Canadian models
3-113-954-1[]
AEP and Chinese models
3-113-954-2[]
UK model
3-113-954-3[]
Russian and Ukrainian models
3-113-954-4[]
PART No.
– Back Panel –
NOTE OF REPLACING THE IC3511 AND IC3513 ON
THE D-VIDEO BOARD
THE D-VIDEO BOARD
IC3511 and IC3513 on the D-VIDEO board cannot exchange with
single. When IC3511 and IC3513 on the D-VIDEO board are
damaged, exchange the entire mounted board.
single. When IC3511 and IC3513 on the D-VIDEO board are
damaged, exchange the entire mounted board.
NOTE OF REPLACING THE IC5002 AND IC5202 ON
THE DSP BOARD
THE DSP BOARD
IC5002 and IC5202 on the DSP board cannot exchange with single.
When IC5002 and IC5202 on the DSP board are damaged, exchange
the entire mounted board.
When IC5002 and IC5202 on the DSP board are damaged, exchange
the entire mounted board.
Ver. 1.2
UPDATE OF SOFTWARE OF IC2003 ON THE
CONTROL BOARD, IC3610 ON THE D-VIDEO
BOARD AND IC5208 ON THE DSP BOARD
CONTROL BOARD, IC3610 ON THE D-VIDEO
BOARD AND IC5208 ON THE DSP BOARD
Perform operation of the following when the update of software of
the IC2003 on the CONTROL board, IC3610 on the D-VIDEO board
and IC5208 on the DSP board is necessary.
the IC2003 on the CONTROL board, IC3610 on the D-VIDEO board
and IC5208 on the DSP board is necessary.
Connect:
Procedure:
1. Connect J1499 on the MAIN board and PC by using the RS-
232C cable.
2. Turn on the main power.
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the RS-232C cable from the J1499 on the MAIN board
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the RS-232C cable from the J1499 on the MAIN board
and PC.
ERROR MESSAGES
If there is a malfunction, the display shows a code of two numbers
and a message. You can check the condition of the system by the
message. Refer to the following table to solve the problem.
and a message. You can check the condition of the system by the
message. Refer to the following table to solve the problem.
messages
cause and response
PROTECTOR
Irregular current is output to the speakers, or
the upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Cheack the speak-
ers connection and turn on the power again.
the upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Cheack the speak-
ers connection and turn on the power again.
for PC
J1499
7
STR-DA5300ES
POWER AMP BLOCK SERVICE POSITION
In checking the Power AMP block, prepare jig (extension cable J-2501-291-A: 2 mm Pitch, 12 cores, Length 300 mm/J-2501-311-A: 2 mm
Pitch, 15 cores, Length 300 mm).
Pitch, 15 cores, Length 300 mm).
insulating sheet
Connect the extension jig (J-2501-311-A) to the
A-CLASS AMP board (CN1505) and
E-VOL board (CN1202).
A-CLASS AMP board (CN1505) and
E-VOL board (CN1202).
E-VOL board
(CN1202)
(CN1202)
A-CLASS AMP board
(CN1505)
(CN1505)
power AMP Block
Connect the extension jig (J-2501-291-A) to the
A-CLASS AMP board (CN1504) and
E-VOL board (CN1201).
A-CLASS AMP board (CN1504) and
E-VOL board (CN1201).
E-VOL board
(CN1201)
(CN1201)
A-CLASS AMP board
(CN1504)
(CN1504)
CONTROL BOARD SERVICE POSITION
In checking the CONTROL board, prepare jig (extension cable J-2501-255-A: 1.25 mm Pitch, 10 cores, Length 300 mm/J-2501-258-A: 1.25
mm Pitch, 16 cores, Length 300 mm/J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm/J-2501-260-A: 1.25 mm Pitch, 20 cores,
Length 300 mm).
mm Pitch, 16 cores, Length 300 mm/J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm/J-2501-260-A: 1.25 mm Pitch, 20 cores,
Length 300 mm).
connect jig (extension cable J-2501-260-A)
to the CONTROL board (CN2006)
and MAIN board (CN1005).
to the CONTROL board (CN2006)
and MAIN board (CN1005).
connect jig (extension cable J-2501-255-A)
to the CONTROL board (CN2008)
and MAIN board (CN1006).
to the CONTROL board (CN2008)
and MAIN board (CN1006).
connect jig (extension cable J-2501-258-A)
to the CONTROL board (CN2004)
and D-CONNECT board (CN2403).
to the CONTROL board (CN2004)
and D-CONNECT board (CN2403).
CONTROL board
(CN2006)
(CN2006)
connect jig (extension cable J-2501-259-A)
to the CONTROL board (CN2005)
and D-CONNECT board (CN2405).
to the CONTROL board (CN2005)
and D-CONNECT board (CN2405).
CONTROL board
(CN2008)
(CN2008)
MAIN board
(CN1006)
(CN1006)
MAIN board
(CN1005)
(CN1005)
CONTROL board
(CN2004)
(CN2004)
CONTROL board
(CN2005)
(CN2005)
D-CONNECT board
(CN2403)
(CN2403)
D-CONNECT board
(CN2405)
(CN2405)
insulating sheet
Ver. 1.5
8
STR-DA5300ES
DIGITAL BOARD SERVICE POSITION
In checking the DIGITAL board, prepare jig (extension cable J-2501-312-A: 1.25 mm Pitch, 11 cores, Length 300 mm).
D-VIDEO/S-VIDEO BOARDS SERVICE POSITION
In checking the D-VIDEO board, prepare two jig (extension cable J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm).
connect jig (extension cable J-2501-312-A)
to the DIGITAL board (CN2203)
and CONTROL board (CN2002).
to the DIGITAL board (CN2203)
and CONTROL board (CN2002).
CONTROL board
(CN2002)
(CN2002)
DIGITAL board
(CN2203)
(CN2203)
Connect jig (extension cable J-2501-259-A)
to the D-VIDEO board (CN3507) and
CONTROL board (CN2001).
to the D-VIDEO board (CN3507) and
CONTROL board (CN2001).
CONTROL board
(CN2001)
(CN2001)
D-VIDEO board
(CN3507)
(CN3507)
Connect jig (extension cable J-2501-259-A)
to the D-VIDEO board (CN3508) and
CONTROL board (CN2009).
to the D-VIDEO board (CN3508) and
CONTROL board (CN2009).
CONTROL board
(CN2009)
(CN2009)
D-VIDEO board
(CN3508)
(CN3508)
S-VIDEO board
Ver. 1.4
Click on the first or last page to see other STR-DA5300ES service manuals if exist.