DOWNLOAD Sony STR-DA5300ES Service Manual ↓ Size: 14.89 MB | Pages: 127 in PDF or view online for FREE

25

5

connector
(CN1405)

6

four screws 
(BVTP3 

× 

8)

6

three screws 
(BVTP3 

× 

8)

7

heart sink section

2

CONNECTOR 2 board

4

CONNECTOR 1 board

3

two connectors
(CN1207, CN1209)

1

two connectors
(CN1205, CN1206)

26

color

pattern

generator

DMPORT

check jig

(Part No.:

J-2501-309-A)

J001

AF

oscillator

set

TV

monitor

FL/FR

speaker

A-VIDEO board

CN6505

MAIN board

TM4002

A-VIDEO board

J6203

All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:

1. While pressing the [TONE MODE] and [DMPORT] buttons, press

the [POWER] button to turn on the main power.

2. The message “MEMORY CLEARING***” appears and the

memories are reset to the default values.

3. When done, the message “MEMORY CLEARED*” appears.

All fluorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:

1. While pressing the [MOVIE] and [DMPORT] buttons, press the

[POWER] button to turn on the main power.

2. All segments and all LEDs turn on.

The preset sound field is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:

1. While pressing the [MUSIC] button, press the [POWER] button

to turn on the main power.

2. The message “S. F. Initialize” appears and initialization is

performed.

Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [POWER] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM”.
3. Press the [POWER] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the  [POWER]

button to turn on the main power.

5. Either the message “AM 9kHz Step” or “AM 10kHz Step”

appears, select the desired step.

The command mode of the remote-commander which this set
receives can be changed.
Procedure:

1. While pressing the [2CH/A. DIRECT] button, press the [POWER]

button to turn on the main power.

2. Either the message “COMMAND MODE [AV1]” or

“COMMAND MODE [AV2]” appears. Select the desired
mode.

1. While pressing the [MUSIC] and [DMPORT] buttons, press the

[POWER] button to turn on the main power.

2. Either the message “SF LOCK [OFF]” or “SF LOCK [ON]”

appears.

Mode to confirm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confirmed that there are no problems in the communication of the
XM antenna and the tranmission of the audio signal.
Procedure:

1. The XM antenna was connected, while pressing the [TUNING

MODE] and [MOVIE] buttons, press the [POWER] button to
turn on the main power.

2. Whenever the [DISPLAY] button is pressed, the output of the

audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1
kHz L and 1 kHz R are switched.

Mode to confirm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confirmed that there are no problems in the
communication of the SIRIUS antenna and the transmission of the
audio signal.
Procedure:

1. The SIRIUS antenna was connected, while pressing the

[TUNING MODE] and [A.F.D.] buttons, press the [POWER] button
to turn on the main power.

2. Whenever the [DISPLAY] button is pressed, the output of the

audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1
kHz L and 1 kHz R are switched.

1. Connect the DMPORT check jig (P/N: J-2501-309-A) with

the DMPORT jack (CN6505) on the A-VIDEO board.

2. While pressing the [A.F.D.] and [DMPORT] buttons, press the

[POWER] button to turn on the main power.

3. The message “DMPORT OK.” appears on the fluorescent

indicator tube and enter the digital media port test mode
(Confirmation of communication line).
When “NO DETECT”, “UART NG” and “UART TO” are
displayed on the fluorescent indicator tube, confirm the
connection of the DMPORT check jig, and enter the mode
again.
Each time the 

 >

  button on the remote commander is pressed,

the connect check and adaptor version check are switched.
Press the 

.

 button on the remote commander, connected

confirmation of the DMPORT check jig is done again.

4. To a pin-jack of the DMPORT check jig input information

relevant to audio signal (sine-wave 1.0 Vrms) and composite
video signal (white 100% 1.0 Vp-p, color bar, etc.).

5. Confirm the output of speakers and monitor TV (Confirmation

of analog signal).

6. To exit from this mode, press the  

x 

 button on the remote

commander.

27

The state that the set is used is memorized.
Procedure:
1. While pressing the 

[MUSIC]

 and 

[MEMORY/ENTER]

 buttons,

press the [POWER] button to turn on the power and “HIS-
TORY MODE” is displayed.

2. Each time the 

 

M

   

m

  key of remote commander is pressed, the

item is switched in order as follows.

Items

Display

Number of protector is generated

PRCT COUNT: XXX

Total use time

TTL_TIME: XXXXH XXM

Sound field setting

XXXXXXXXXXXXXXXX

Input when protect is detected

INPUT: XXXXXXXXXX

Input mode setting

INMODE: XXXXXXXXXXXX

Input mode under lick state

DSEL: XXXXXXXXXXXXXXX

Stream under input

STREAM: XXXXXXX

Channel information

CONFIG:XXXXXXX

State of headphone

HEAD PHONES: XXX

Volume

VOL: XXXdB

EQ setting value

BASS:    XXXdB

TREB:    XXXdB

Lv FL/FR  XXXX/XXXX

Level collection value

Lv SL/SR  XXXX/XXXX

each channel

Lv CT/SW  XXXX/XXXX

Lv BL/BR  XXXX/XXXX

Total time of power on

TTL_P_ON: XXXXH XXM

28

1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT],

[MUSIC], [MOVIE] button in order, the message “MENU SPECIALIZED!” appears.

2. Press the 

M

  

m

 button of the remote commander, the message “<<< SPECIAL >>>” appears.

3. Press the 

,

 button of the remote commander, the item is appears.

4. Each time the 

M

  

m

 button of the remote commander is pressed, the item is switched in order as follows.

Some items can change the content. Display the cursor by pressing the 

,

 button of the remote commander, and changing the content

by pressing the  

M

  

m

  button of the remote commander, and fix the content by pressing the 

<

  button of the remote commander when

you want to change the content of the item.

5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in

order again, the message “MENU SPECIALIZED OFF” appears.

Items

Display

Remark

Video factory menu

<VIDEO FACTORY MENU>

Menu mode to enter video calibration menu and DDR access check menu

If the [ENTER] button of the remote commander is pressed, entering the

menu, and operating two the following menu become possible

Video calibration

V.CALIBRATION START?

Procedure:

(Video factory menu)

1. “DVD” is selected by using [INPUT SELECTOR] dial.

2. Connect a color pattern generator to the COMPONENT VIDEO

ASSIGNABLE (INPUT ONLY) DVD/BD IN jack (J6002) on the A-

VIDEO board, DVD/BD VIDEO IN jack (J6201) on the A-VIDEO

board, DVD/BD S VIDEO IN jack (J6901) on the S-VIDEO board and

EXT VIDEO IN jack (J6904).

3. Input 100% color bars signal from the color pattern generator.

4. Menu that measures individual difference of hardness by automatic

operation in pressing the [ENTER] button of the remote commander, and

corrects reference value.

In a measurement once, only one of NTSC/PAL/HD can be measured

“Check XXXX V-IN” at display:

Video signal necessary for the measurement while measuring it last time

was not detected and it became an error

Confirm the input of the video of the terminal connection etc. , and

measure the [ENTER] button of the remote commander again pressing

DDR access check

DDR CHECK [XX] sec

XX: Time to do access check on DDR (for design evaluation)

(Video factory menu)

Auto cal mic test

SPEAKER OUT [XXXXX]

XXXXX: Selection of speaker output audio

[SOURCE]: nomally mode, [MIC]: mode that output audio from mic from

speaker

FL display fonts test

FL FONT [0x ** = X]

**: 20 to FE, X: character

FL display test

ALL ON

Each time DISPLAY button to change as follows

all on 

t test pattern 1 t test pattern 2 t all off t all on

HDCP key read

HDCP KEY READ [XXX]

XXX: ON or OFF

DSP SRAM check

<DSP SRAM CHECK>

XX: OK or NG

r

[ENTER] button of the remote

OK: success access SRAM, NG: fail access to SRAM

commander

SRAM1 [XX] SRAM2 [XX]

FAROUDJA update

FAROUDJA UPDATE [XXX]

XXX: ON or OFF

Model version display

##### *** vX. XX @@@@

#####: Model

***: Destination

X.XX: System controller software version

@@@@: Sum value of flash memory in the system controller

Video Ucom version display

Video Ucom Ver X. XX

X.XX: Video system controller software version

FAROUDJA version display

FAROUDJA Ver X. XX

X.XX: Video Processor software version

GUI CG-ROM version display

GUI CGROM Ver X. XX

X.XX: CG-ROM software version

DSP Ucom version display

DSP Ucom Ver X. XX

X.XX: DSP controller version

DSP serial flash version display

DSP SFLASH Ver X. XX

X.XX: Serial flash software version

DSP parallel flash version display

DSP PFLASH Ver X. XX

X.XX: DSP parallel flash version

DSP halt

DSP HALT [XXX]

XXX: ON or OFF

DSP RAM

[*****]=XXXXXXXX

Mode that refers to internal RAM of DSP (for design evaluation)