Sony STR-DA5300ES Service Manual ▷ View online
29
STR-DA5300ES
Items
Display
Remark
Super reset
SUPER RESET [XXX]
Not used for the servicing
If super reset is performed, “up convert signal level adjustment” will also be
initialized
When EEPROM initialization is required, perform the “memory clearing
mode”
RAM watch menu
XXX
XXX: For monitor of various internal RAM (for design evaluation)
EERROM debug
EEPROM [****] [XX]
****: EEPROM address, XX: EEPROM data
Protector on/off
PROTECTOR ON/OFF [XXX]
XXX: ON or OFF
Model/destination change
MODEL [##### * * * *] X X
#####: Model, ****: Destination, XX: At or fx
Audio swap
SWAP [XXXXXXXXXXX]
Switching with
M m button of the remote commander
Decoder select
DECODER SEL [XXXX]
XXXX: AUTO, LEGACY, DDPLUS, TRUEHD, DTSEXP, MP3SUR (for
debug)
Volume value display (FL/FR)
FL**** FR XXXX
****: Front L-ch volume value, XXXX: Front R-ch volume value
Volume value display (SL/SR)
SL**** SR XXXX
****: Surround L-ch volume value, XXXX: Surround R-ch volume value
Volume value display (CT/SW)
CT**** SW XXXX
****: Center volume value, XXXX: Sub woofer volume value
Volume value display (SBL/SBR)
SBL**** SBR XXXX
****: Surround back L-ch volume value, XXXX: Surround back R-ch
volume value
DAC mute information disclosure 1 DAC MUTE U XXXXXXXX
Display of module information to demand muting in system controller (for
design evaluation)
DAC mute information disclosure 2 DAC MUTE L XXXXXXXX
Display of module information to demand muting in system controller (for
design evaluation)
2nd volume value display
2nd VOLUME XXX
XXX: 2nd room volume value (00 to
∞
)
FL display duty change
DARK OUT DUTY [XXX%]
XXX: Duty value of FL display (0% to 100%)
DMPORT debug
DMP KEY DEBUG [XXX]
XXX: ON or OFF (for debug)
Bus overflow debug HA link
OVERFLOW HAL R [XX]
XX: Counter of overflow receive buffer
(receive)
Bus overflow debug HA link
OVERFLOW HAL S [XX]
XX: Counter of overflow transmit buffer
(transmit)
Bus overflow debug DMPORT
OVERFLOW CLA [XX]
XX: Counter of overflow CLA transmit buffer
30
STR-DA5300ES
SECTION 5
ELECTRICAL ADJUSTMENTS
BIAS ALIGNMENT ADJUSTMENT
Note:
After 10 minutes or more have passed since the power supply was
turned on, this adjustment is done.
turned on, this adjustment is done.
Connection:
Note:
Pin 3, 4 of CN1611 are open.
Procedure:
1. Connect a digital voltmeter to the CN1561 (CN1611, CN1761,
CN1861).
2. Press the [POWER] button to turn on the main power.
3. Adjust the RV1501 (RV1551, RV1601, RV1701, RV1751,
3. Adjust the RV1501 (RV1551, RV1601, RV1701, RV1751,
RV1801, RV1851) so that the digital voltmeter reading is 5 mV
to 20 mV.
to 20 mV.
Adjustment and Connection Location:
+
–
–
digital voltmeter
CN1561 (CN1611, CN1761, CN1861) pin
1
, CN1561 (CN1761, CN1861) pin
3
CN1561 (CN1611, CN1761, CN1861) pin
2
, CN1561 (CN1761, CN1861) pin
4
Adjustment hole
for RV1801
(SBL)
– BIAS Board (Conductor Side) –
– PROTECTOR (F-C) Board
(Component Side) –
(Component Side) –
– PROTECTOR (SURR) Board
(Component Side) –
(Component Side) –
– PROTECTOR (SB) Board
(Component Side) –
(Component Side) –
4 1
CN1561
4 1
CN1761
4 1
CN1611
4 1
CN1861
Adjustment hole
for RV1851
(SBR)
Adjustment hole
for RV1601
(CENTER)
Adjustment hole
for RV1501
(F-L)
Adjustment hole
for RV1551
(F-R)
Adjustment hole
for RV1701
(SUR-L)
Adjustment hole
for RV1751
(SUR-R)
STR-DA5300ES
31
31
STR-DA5300ES
VIDEO CALIBRATION ADJUSTMENT
Adjustment to decide the standard of the video input signal.
Note:
After replacing D-VIDEO board, or after “SUPER RESET” of the
special menu mode is executed, perform this adjustment.
special menu mode is executed, perform this adjustment.
1. Adjustment jig
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component, the composite and the S
video at the same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component terminal
and the video terminal at the same time (Substitution model name
example: BDP-S350).
However, please do the following signal output confirmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
HD color bar signal to the component, the composite and the S
video at the same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component terminal
and the video terminal at the same time (Substitution model name
example: BDP-S350).
However, please do the following signal output confirmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
1-1. Component signal
Checking Component Video Output Y
Signal
DVD standard disc color bars (100%)
Check point
COMPONENT VIDEO OUT (Y)
terminal (75
Ω
terminated)
Specification
1.00
±
0.03 Vp-p
Checking Component Video Output B-Y
Signal
DVD standard disc color bars (100%)
Check point
COMPONENT VIDEO OUT (P
B
/C
B
)
terminal (75
Ω
terminated)
Specification
0.70
±
0.03 Vp-p
Checking Component Video Output R-Y
Signal
DVD standard disc color bars (100%)
Check point
COMPONENT VIDEO OUT (P
R
/C
R
)
terminal (75
Ω
terminated)
Specification
0.70
±
0.03 Vp-p
1-2. S Video signal
Checking S Video Output S-Y
Signal
DVD standard disc color bars (100%)
Check point
S VIDEO OUT (S-Y) terminal
(75
Ω
terminated)
Specification
1.00
±
0.03 Vp-p
Checking S Video Output S-C
Signal
DVD standard disc color bars (100%)
Check point
S VIDEO OUT (S-C) terminal
(75
Ω
terminated)
Specification
286
±
30 m Vp-p
1-3. Composite signal
Video level confirmation
Signal
DVD standard disc color bars (100%)
Check point
LINE OUT (VIDEO) terminal
(75
Ω
terminated)
Specification
1.00
±
0.03 Vp-p
2. Video calibration adjustment
2-1. Connection
2-1. Connection
2-2. Procedure for color pattern generator
1. It connects of step 2-1, and the turn on the main power.
2. “DVD” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [POWER] button to turn off the main power.
5. While pressing the [MEMORY/ENTER], [MUSIC] and
2. “DVD” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [POWER] button to turn off the main power.
5. While pressing the [MEMORY/ENTER], [MUSIC] and
[DMPORT] buttons, press the [POWER] button to turn on the
main power. When correctly entering the test mode “V.CAL
COMPLETE N:P:H” is displayed (keeps pressing three buttons
until the message appears).
main power. When correctly entering the test mode “V.CAL
COMPLETE N:P:H” is displayed (keeps pressing three buttons
until the message appears).
6. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the display
changes from “NTSC:MW -----” to “NTSC:MW OK C S V
E” little by little. Finally, the display returns to the display of
“V.CAL COMPLETE N:P:H”.
changes from “NTSC:MW -----” to “NTSC:MW OK C S V
E” little by little. Finally, the display returns to the display of
“V.CAL COMPLETE N:P:H”.
7. Input PAL color bars signal from the color pattern generator.
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color
pattern generator.
10. Perform step 6 to 7 for the HD signal adjustment.
11. The turn off the main power.
11. The turn off the main power.
Ver. 1.6
1.00
±
0.03 Vp-p
0.70
±
0.03 Vp-p
0.70
±
0.03 Vp-p
1.00
±
0.03 Vp-p
286
±
30 mVp-p
1.00
±
0.03 Vp-p
color pattern
generator
or
Blu-ray
Disc player
set
S-VIDEO board
EXT VIDEO IN jack (J6904)
EXT VIDEO IN jack (J6904)
A-VIDEO board
MONITOR VIDEO OUT
jack (J6206)
MONITOR VIDEO OUT
jack (J6206)
A-VIDEO board
VIDEO 1 OUT jack
(J6205)
VIDEO 1 OUT jack
(J6205)
TV
monitor
A-VIDEO board COMPONENT VIDEO ASSIGNABLE
(INPUT ONLY) DVD/BD IN jack (J6002)
A-VIDEO board DVD/BD VIDEO IN jack (J6201)
S-VIDEO board DVD/BD S VIDEO IN jack (J6901)
(INPUT ONLY) DVD/BD IN jack (J6002)
A-VIDEO board DVD/BD VIDEO IN jack (J6201)
S-VIDEO board DVD/BD S VIDEO IN jack (J6901)
2-3. Procedure for Blu-ray Disc player
1. It connects of step 2-1, and the turn on the main power of set
and Blu-ray Disc player.
2. “DVD” is selected by using [INPUT SELECTOR] dial.
3. Press the OPEN/CLOSE button of the Blu-ray Disc player,
3. Press the OPEN/CLOSE button of the Blu-ray Disc player,
and DVD test disc “HLX-504 (Part No. J-6090-088-A)” or
“HLX-513 (Part No. J-2501-305-A)” is insert. The disc
playback automatically becomes start “Main Menu” is display.
“HLX-513 (Part No. J-2501-305-A)” is insert. The disc
playback automatically becomes start “Main Menu” is display.
4. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
5. Press the [POWER] button to turn off the main power of the
set.
6. While pressing the [MEMORY/ENTER], [MUSIC] and
[DMPORT] buttons, press the [POWER] button to turn on the
main power of the set. When correctly entering the test mode
“V.CAL COMPLETE N:P:H” is displayed (keeps pressing
three buttons until the message appears).
main power of the set. When correctly entering the test mode
“V.CAL COMPLETE N:P:H” is displayed (keeps pressing
three buttons until the message appears).
7. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the display
changes from “NTSC:MW -----” to “NTSC:MW OK C S V
E” little by little. Finally, the display returns to the display of
“V.CAL COMPLETE N:P:H”.
changes from “NTSC:MW -----” to “NTSC:MW OK C S V
E” little by little. Finally, the display returns to the display of
“V.CAL COMPLETE N:P:H”.
8. Press the OPEN/CLOSE button of the Blu-ray Disc player,
and change to DVD test disc “HLX-506 (Part No. J-6090-
077-A)” or “HLX-507 (Part No. J-6090-078-A)”. The disc
playback automatically becomes start “Main Menu” is display.
077-A)” or “HLX-507 (Part No. J-6090-078-A)”. The disc
playback automatically becomes start “Main Menu” is display.
9. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
10. The PAL signal adjustment is begun when press the cross
(center of cursor) button of remote commander. Finally, the
display returns to the display of “V.CAL COMPLETE N:P:H”.
display returns to the display of “V.CAL COMPLETE N:P:H”.
11. Press the OPEN/CLOSE button of the Blu-ray Disc player,
and change to DVD test disc “HLX-104 (Part No. J-6090-
199-A)”. The disc playback automatically becomes start “Main
Menu” is display.
199-A)”. The disc playback automatically becomes start “Main
Menu” is display.
12. “59.94Hz, 1080i”
→
“1.Video Signal”
→
“1.Color Bar 100%”
is selected, and 100% in the color bar is displayed in the TV
monitor, playing the Blu-ray Disc player is pause playback.
monitor, playing the Blu-ray Disc player is pause playback.
13. The video output of the Blu-ray Disc player is switched 1080i
(The output from the component terminal of the Blu-ray Disc
player becomes 1080i output).
player becomes 1080i output).
14. The HD signal adjustment is begun when press the cross (center
of cursor) button of remote commander. Finally, the display
returns to the display of “V.CAL COMPLETE N:P:H”.
returns to the display of “V.CAL COMPLETE N:P:H”.
15. The turn off the main power.
STR-DA5300ES
32
32
STR-DA5300ES
FM AUTO STOP CHECK
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency: A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF)
ANT input : 35 dBu (EMF)
Note:
Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confirm that input frequency of A, B and C are detected and
automatic scanning stops.
When the station signal is received in good condition, automatic
scanning stops.
scanning stops.
signal
generator
set
Click on the first or last page to see other STR-DA5300ES service manuals if exist.