Sony STR-DA2800ES Service Manual ▷ View online
STR-DA2800ES
5
Ver. 1.3
NOTE OF REPLACING THE IC3903 AND IC3904 ON
THE DCDC BOARD
IC3903 and IC3904 on the DCDC board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
THE DCDC BOARD
IC3903 and IC3904 on the DCDC board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
NOTE OF REPLACING THE IC3500 AND IC3700 ON
THE D-VIDEO BOARD
IC3500 and IC3700 on the D-VIDEO board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
THE D-VIDEO BOARD
IC3500 and IC3700 on the D-VIDEO board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
NOTE OF REPLACING THE IC3505 AND IC3506 ON
THE D-VIDEO BOARD
Replacement of IC3505 and IC3506 on the D-VIDEO board used
in this unit requires a special tool.
THE D-VIDEO BOARD
Replacement of IC3505 and IC3506 on the D-VIDEO board used
in this unit requires a special tool.
NOTE OF REPLACING THE IC5001 ON THE DSP
BOARD
IC5001 on the DSP board cannot exchange with single. When this
part is damaged, exchange the complete mounted board.
BOARD
IC5001 on the DSP board cannot exchange with single. When this
part is damaged, exchange the complete mounted board.
NOTE OF REPLACING THE IC101, IC501 AND IC2601
ON THE NETWORK BOARD
IC101, IC501 and IC2601 on the NETWORK board cannot ex-
change with single. When these parts are damaged, exchange the
complete mounted board.
ON THE NETWORK BOARD
IC101, IC501 and IC2601 on the NETWORK board cannot ex-
change with single. When these parts are damaged, exchange the
complete mounted board.
NOTE OF REPLACING THE IC106, IC107, IC206 AND
IC207 ON THE NETWORK BOARD
Replacement of IC106, IC107, IC206 and IC207 on the NET-
WORK board used in this unit requires a special tool.
IC207 ON THE NETWORK BOARD
Replacement of IC106, IC107, IC206 and IC207 on the NET-
WORK board used in this unit requires a special tool.
MODEL IDENTIFICATION
Distinguish the model by UWA-C4Z connector on back panel.
Distinguish the model by UWA-C4Z connector on back panel.
– Back Panel –
US and Canadian models:
UWA-C4Z connector
does exist.
UWA-C4Z connector
does exist.
AEP model:
UWA-C4Z connector
does not exist.
UWA-C4Z connector
does not exist.
NEW/FORMER TYPES DISCRIMINATION (US model only)
In US model of this unit, the specifi cations have been changed in
the midway of production.
Repair after distinguishing each type unit to doing the repair refer-
ring to the following.
In US model of this unit, the specifi cations have been changed in
the midway of production.
Repair after distinguishing each type unit to doing the repair refer-
ring to the following.
– Back Panel –
– Remote Control –
SERIAL NO.
88xxxxx : Former type
85xxxxx : New type
88xxxxx : Former type
85xxxxx : New type
Not available : Former type
Available
Available
: New type
Remote control name
RM-AAU155 : Former type
RM-AAU195 : New type
RM-AAU155 : Former type
RM-AAU195 : New type
“NETFLIX” button
Available
Available
: Former type
Not available : New type
“SUBTITLE” symbol
Available
Available
: Former type
Not available : New type
STR-DA2800ES
6
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitors (C905 on
the ACDC board) to discharge the capacitors (C905 on the ACDC
board).
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitors (C905 on
the ACDC board) to discharge the capacitors (C905 on the ACDC
board).
– ACDC Board (Conductor Side) –
C905
800
:/2 W
ADVANCE PREPARATION OF REPAIR
(US and Canadian models only)
This unit can perform “PRO-UPGRADE” by C4 (Control4) dealer.
When the user is performing “PRO-UPGRADE”, GUI of C4
(Control4) world is displayed.
Display GUI in the following procedure and confi rm the state of
displayed GUI.
(US and Canadian models only)
This unit can perform “PRO-UPGRADE” by C4 (Control4) dealer.
When the user is performing “PRO-UPGRADE”, GUI of C4
(Control4) world is displayed.
Display GUI in the following procedure and confi rm the state of
displayed GUI.
Connection:
STR-
DA2800ES
monitor
D-VIDEO board
HDMI OUT A ARC connector
(CN3502)
HDMI OUT A ARC connector
(CN3502)
HDMI cable
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn on the main power.
2. Press the [HOME] button of remote commander.
3. “PRO-UPGRADE” is not performed when the following
3. “PRO-UPGRADE” is not performed when the following
screen is displayed.
Note: If the following processing is performed to this unit by which
“PRO-UPGRADE” was performed, this unit returns to the state
before “PRO-UPGRADE” is performed.
before “PRO-UPGRADE” is performed.
•
Complete NETWORK board replacing
•
Factory
reset
Since the change to C4 (Control4) world can perform only by
C4 (Control4) dealer, fully work carefully.
C4 (Control4) dealer, fully work carefully.
NOTE OF REPLACING THE COMPLETE NETWORK
BOARD
When the complete NETWORK board is exchanged, the MAC ad-
dress has been changed.
Please print and cut out the following explanations, and return it
with the unit that completes the repair.
BOARD
When the complete NETWORK board is exchanged, the MAC ad-
dress has been changed.
Please print and cut out the following explanations, and return it
with the unit that completes the repair.
MAC address of this receiver has been changed by this repair.
The customer who uses the MAC address fi ltering function of
connected access point equipment please set it again. MAC ad-
dress is possible to confi rm it on the System Information screen
of this unit. Please refer to “Adjusting Settings” on the operating
instructions for details.
The customer who uses the MAC address fi ltering function of
connected access point equipment please set it again. MAC ad-
dress is possible to confi rm it on the System Information screen
of this unit. Please refer to “Adjusting Settings” on the operating
instructions for details.
CONFIRMATION OF NETWORK OPERATION
Note: When this confi rmation is executed, IP address is changed.
Necessary machinery and materials:
•
•
PC (Windows XP/Vista)
•
Router (Transmission rate is 100 Mbps or more, built-in DHCP
server function)
server function)
•
Two LAN cables
(Category 5 cable, normal type or shield type)
• Monitor
•
•
Supplied remote commander (RM-AAU155)
(US and Canadian models)
•
Supplied remote control (RM-AAP082) (AEP model)
Connection:
(The router need not be connected with the internet)
(The router need not be connected with the internet)
LAN cable
router
PC
STR-
DA2800ES
monitor
NETWORK board
jack (CN2502)
D-VIDEO board
HDMI OUT A ARC connector
(CN3502)
HDMI OUT A ARC connector
(CN3502)
HDMI cable
Procedure:
1. The setting of LAN of PC is setting to the automatic IP address
1. The setting of LAN of PC is setting to the automatic IP address
assignment.
It changes to the setting that displays the image in the monitor.
2. Perform connection with reference to connection fi gure.
3. The power supply of the router is turn on, next, the power sup-
3. The power supply of the router is turn on, next, the power sup-
ply of PC and this unit is turn on.
4. Press the [HOME] button of the remote commander, the home
menu is displayed in the monitor.
5. The “Settings” is selected on the home menu, and press the [
]
button of remote commander.
6. The “Network Settings” is selected , and press the [
] button
of remote commander.
7. The “Internet Settings” is selected , and press the [
] button of
remote commander.
8. The “Network Setup” is selected , and press the [
] button of
remote commander.
9. The “Auto” is selected , and press the [
] button of remote
commander.
10. The “The network will be confi gured with the following set-
tings.” is displayed, and press the [
,
] button of remote com-
mander.
11. The “Save & Connect” is selected , and press the [
] button of
remote commander.
12. The automatically connect function is performed.
13. Confi rm that the “Internet Access: OK” has been displayed,
13. Confi rm that the “Internet Access: OK” has been displayed,
and press the [
] button of remote commander.
14. Press the [\/1] button to turn off the main power.
Ver. 1.2
STR-DA2800ES
7
Jig No.
Jig Name
Part No.
Pitch (mm)
Cores
Remark
1
1.25_22_M
J-2501-350-A
1.25
22
For CONTROL board (CN2515, 2701)
1.25_22_F
For MAIN board (CN302, 303)
Flexible fl at cable 22P
J-2501-364-A
Length 300 mm
2
1.25_26_F
J-2501-356-A
1.25
26
For CONTROL board (CN2891)
1.25_26_F
For D-AUDIO board (CN2231)
Flexible fl at cable 26P
J-2501-365-A
Length 300 mm
CONTROL BOARD SERVICE POSITION
•
•
Please connect following extension jig.
Connect extension jig 1
to the CONTROL board (CN2515)
and MAIN board (CN302).
to the CONTROL board (CN2515)
and MAIN board (CN302).
Connect extension jig 1
to the CONTROL board (CN2701)
and MAIN board (CN303).
to the CONTROL board (CN2701)
and MAIN board (CN303).
Connect extension jig 2
to the CONTROL board (CN2891)
and D-AUDIO board (CN2231).
to the CONTROL board (CN2891)
and D-AUDIO board (CN2231).
CONTROL board
(CN2515)
(CN2515)
MAIN board
(CN303)
(CN303)
MAIN board
(CN302)
(CN302)
CONTROL board
(CN2891)
(CN2891)
CONTROL board
(CN2701)
(CN2701)
D-AUDIO board
(CN2231)
(CN2231)
insulating sheet
alligator clip
Note: Connect altogether the metal part
Note: Connect altogether the metal part
on the boards connected with the
chassis using the alligator clip.
SUB D-VIDEO BOARD SERVICE POSITION
insulating sheet
SUB D-VIDEO board
alligator clip
Note: Connect altogether the metal part
Note: Connect altogether the metal part
on the boards connected with the
chassis using the alligator clip.
chassis using the alligator clip.
STR-DA2800ES
8
Jig No.
Jig Name
Part No.
Pitch (mm)
Cores
Remark
2
1.25_26_F
J-2501-356-A
1.25
26
For CONTROL board (CN2891)
1.25_26_F
For D-AUDIO board (CN2003)
Flexible fl at cable 26P
J-2501-365-A
Length 300 mm
3
2.00_19_M
J-2501-368-A
1.25
19
For MAIN board (CN301)
2.00_19_F
For D-AUDIO board (CN1114)
Flexible fl at cable 19P
J-2501-370-A
Length 400 mm
4
2.00_5_M
J-2501-369-A
1.25
5
For MAIN board (CN300)
2.00_5_F
For D-AUDIO board (CN2401)
Flexible fl at cable 5P
J-2501-371-A
Length 400 mm
D-AUDIO BOARD SERVICE POSITION
•
•
Please connect following extension jig.
OPT-COAX board
insulating sheet
Connect extension jig 2
to the D-AUDIO board (CN2003)
and CONTROL board (CN2891).
to the D-AUDIO board (CN2003)
and CONTROL board (CN2891).
Connect extension jig 4
to the D-AUDIO board (CN2401)
and MAIN board (CN300).
to the D-AUDIO board (CN2401)
and MAIN board (CN300).
Connect extension jig 3
to the D-AUDIO board (CN1114)
and MAIN board (CN301).
to the D-AUDIO board (CN1114)
and MAIN board (CN301).
CONTROL board
(CN2891)
(CN2891)
alligator clip
Note: Connect altogether the metal part
Note: Connect altogether the metal part
on the boards connected with the
chassis using the alligator clip.
D-AUDIO board
(CN2003)
(CN2003)
D-AUDIO board
(CN1114)
(CN1114)
D-AUDIO board
(CN2401)
(CN2401)
MAIN board
(CN301)
(CN301)
MAIN board
(CN300)
(CN300)
Click on the first or last page to see other STR-DA2800ES service manuals if exist.