Sony STR-DA2800ES Service Manual ▷ View online
STR-DA2800ES
21
2-13. D-VIDEO BOARD BLOCK-1
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
1 Cut two cable ties.
(See Fig. H)
1 Cut the cable tie.
(See Fig. I)
3 connector
(CN3523)
(CN3523)
4 connector
(CN3607)
(CN3607)
5 connector
(CN3509)
(CN3509)
< Fig. I >
Wire setting
Note 3: The wire must not touch heat sink.
D-VIDEO board
2 Remove wire from wiring stopper.
(See Fig. H)
wiring stopper
2 Remove wire from wiring stopper.
(See Fig. I)
6 wire (flat type) (13 core)
(CN3510)
(CN3510)
colored line
colored line
Insert is straight to the interior.
Insert is incline
wire (flat type)
wire (flat type)
connector
connector
OK
NG
Note 2: When installing the wire (flat type), ensure the colored line.
No slanting after insertion.
cable tie
cable tie
cable tie
< Fig. H >
D-VIDEO board
wiring stopper
STR-DA2800ES
22
2-14. D-VIDEO BOARD BLOCK-2
Ver. 1.2
B
A
3 screw
(BVTP3
(BVTP3
u 8)
3 screw
(BVTP3
(BVTP3
u 8)
3 screw
(BVTP3
(BVTP3
u 8)
3 screw
(BVTP3
(BVTP3
u 8)
4 clamp
4 clamp
A
B
6 Push two buttons of connector.
5 Remove the D-VIDEO board block
in the direction of an arrow.
8 D-VIDEO board block
7 flexible flat cable (FFC3)
(CN3101)
(CN3101)
SUB D-VIDEO board
(CN7001)
(CN7001)
short side
long side
D-VIDEO board
(CN3101)
(CN3101)
Note: When installing the flexible flat cable (FFC3),
check a direction and install correctly.
2 screw
(BVTP3
(BVTP3
u 8)
2 screw
(BVTP3
(BVTP3
u 8)
1 seven screws
(B3
(B3
u 5)
– Rear side view –
(AEP)
3 screw
(BVTP3
(BVTP3
u 8)
(AEP)
STR-DA2800ES
23
2-15. D-VIDEO BOARD
1 two screws
(BVTP3
(BVTP3
u 8)
2 HDMI-7 bracket block
4 heat sink (2011)
5 radiation sheet
1 screw
(BVTP3
(BVTP3
u 8)
6 D-VIDEO board
3 Bend the claw in the
direction of an arrow.
Note: When installing the heat sink (2011), check
that the radiation sheet has not shifted.
heat sink (2011) hole
heat sink (2011) hole
radiation sheet
radiation sheet
OK
IC3500
IC3500
NG
STR-DA2800ES
24
2-16. SURR SPEAKER BOARD
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
1 Cut the cable tie.
(See Fig. J)
7 Cut the cable tie.
(See Fig. K)
8 connector
(CN393)
(CN393)
0 SURR SPEAKER board
SURR SPEAKER board
4 two screws
(BVTP3
(BVTP3
u 8)
2 screw
(BVTP3
(BVTP3
u 8)
5 screw
(BV
(BV
S4
u 8)
2 two screws
(BVTP3
(BVTP3
u 8)
3 crossbeam_fan bracket block
6 center bracket
9 three screws
(BV/ring)
(BV/ring)
:LUHsetting
Note 2: The wire must not touch heat sink.
Note 2: The wire must not touch heat sink.
MAIN board
MAIN board
cable tie
cable tie
)ig-!
)ig.!
–
5eDUsiGeYieZ–
Click on the first or last page to see other STR-DA2800ES service manuals if exist.