Sony STR-DA2800ES Service Manual ▷ View online
STR-DA2800ES
25
2-17. HDMI CABLE (HDC1)
5 HDMI cable
(HDC1)
(HDC1)
4 connector
(CN701)
(CN701)
1 saranet cushion
(See Fig. L)
:LUHVHWWLQJ
)LJ/!
saranet cushion
NETWORK board
2 Cut the cable tie.
3 clamp filter (ferrite core)
(FC3)
(FC3)
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
Note 2: The wire must not touch heat sink.
STR-DA2800ES
26
2-18. NETWORK BOARD-1
Ver. 1.2
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
1 Cut the cable tie.
(See Fig. M)
2 screw
(BVTP3
(BVTP3
u 8)
C
C
2 two screws
(BVTP3
(BVTP3
u 8)
2 two saranet cushions
(See Fig. N)
6 connector
(CN1002)
(CN1002)
9 connector
(CN1106)
(CN1106)
7 connector
(CN605)
(CN605)
8 connector
3 crossbeam_fan bracket block
:LUHsetting
Note 2: The wire must not touch heat sink.
Note 2: The wire must not touch heat sink.
MAIN board
cable tie
)ig0!
)ig1!
4 Remove wire from two lead pins.
(See Fig. N)
NETWORK board
CONTROL board
lead pin
5 Remove wire from wiring stopper.
(See Fig. N)
wiring stopper
saranet cushion
saranet cushion
(AEP)
lead pin
(AEP)
STR-DA2800ES
27
2-19. NETWORK BOARD-2
2 screw
(BVTP3
(BVTP3
u 8)
2 screw
(BVTP3
(BVTP3
u 8)
2 two screws
(BVTP3
(BVTP3
u 8)
1 screw
(P3
(P3
u 6)
2 screw
(BVTP3
(BVTP3
u 8)
9 two screws
(BVTP3
(BVTP3
u 8)
2 screw
(BVTP3
(BVTP3
u 8)
4 claw
5 beam-network bracket block
0 bracket (NW-R)
6 connector
(CN1103)
(CN1103)
7 connector
(CN1104)
(CN1104)
3 wiring stopper
8 Remove the NETWORK board block
in the direction of an arrow.
qa NETWORK board
– Rear side view –
Note: When replacing the NETWORK board, refer to “NOTE
OF REPLACING THE NETWORK BOARD” (page 6).
STR-DA2800ES
28
2-20. FRONT PANEL BLOCK
9 Remove the front panel block
in the direction of an arrow.
qa front panel block
(See Fig. O)
0 Pull out wire.
0 Pull out wire.
DISPLAY board
USB board
STBY board
– Ftont panel block inner view –
8 seven screws
(BVTP3
(BVTP3
u 8)
8 two screws
(BVTP3
(BVTP3
u 8)
lead pin
< Fig. R >
< Fig. Q >
< Fig. O >
< Fig. P >
Wire setting
Note 3: The wire must not touch heat sink.
Note 3: The wire must not touch heat sink.
Note 2: The wire must not touch
power
power
transformer.
Note 2: The wire must not touch
power
power
transformer.
Note 2: The wire must not touch
power
power
transformer.
3 Remove wire from two lead pins.
(See Fig. Q)
3 Remove wire from
two lead pins.
(See Fig. R)
lead pin
lead pin
lead pin
lead pin
MAIN board
ACDC board
GUIDE_A board
Note 3: The wire must not touch heat sink.
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
1 Cut the cable tie.
(See Fig. P)
1 Cut the cable tie.
(See Fig. P)
2 saranet cushion
(See Fig. P)
saranet
cushion
cushion
cable tie
F
E
E
F
D
D
7 connector (CN308)
6 connector
(CN6505)
(CN6505)
5 connector (CN6203)
4 connector (CN6204)
(AEP)
(AEP)
1 Cut three cable ties.
(See Fig. R)
1 Cut three cable ties.
(See Fig. R)
(AEP)
(US, CND)
STBY board
cable tie
cable tie
cable tie
cable tie
cable tie
(AEP)
(AEP)
(US, CND)
GUIDE_A board
(US, CND)
Ver. 1.2
• Abbreviation
CND : Canadian model
CND : Canadian model
Click on the first or last page to see other STR-DA2800ES service manuals if exist.