Sony STR-DA2800ES Service Manual ▷ View online
STR-DA2800ES
29
2-21. A-VIDEO BOARD-1
• Abbreviation
CND : Canadian model
CND : Canadian model
Ver. 1.2
1 clamp filter (ferrite core)
(FC3)
(FC3)
(See Fig. S)
qa screw
(BVTP3
(BVTP3
u 8)
qa three screws
(BVTP3
(BVTP3
u 8)
lead pin
lead pin
lead pin
lead pin
< Fig. S >
Wire setting
Note 2: The wire must not
touch heat sink.
Note 3: The wire must not touch IC502, IC507, IC512 and IC517.
3 Remove wire from lead pin.
(See Fig. S)
3 Remove wire from two lead pins.
(See Fig. T)
3 Remove wire from three lead pins.
(See Fig. T)
3 Remove wire from lead pin.
(See Fig. T)
3 Remove wire from lead pin.
(See Fig. T)
CONTROL board
A-VIDEO board
MAIN board
4 connector
(CN1406)
(CN1406)
6 connector
(CN2516)
(CN2516)
0 connector
(CN6505)
(CN6505)
8 connector
(CN6204)
(CN6204)
9 connector
(CN6203)
(CN6203)
7 connector (CN6506)
5 connector
(CN2100)
(CN2100)
I
I
H
G
G
H
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
2 Cut the cable tie.
(See Fig. S)
– Rear side view –
clamp filter
(ferrite core) (FC3)
(ferrite core) (FC3)
clamp filter
(ferrite core) (FC3)
(ferrite core) (FC3)
Note 2: The wire must not
touch heat sink.
cable tie
cable tie
cable tie
cable tie
guide line
MAIN board
GUIDE_B board
2 Cut three cable ties.
(See Fig. T)
(AEP)
(US, CND)
< Fig. T >
(US, CND)
(AEP)
(AEP)
Note 2: The wire must not
touch heat sink.
cable tie
GUIDE_B board
Note 4:
Arrange to the
MAIN board side
than the guide line.
Arrange to the
MAIN board side
than the guide line.
STR-DA2800ES
30
2-22. A-VIDEO BOARD-2
2-23. CONTROL BOARD
3 screw
(BV
(BV
S4
u 8)
4 center bracket
6 A-VIDEO board
1 Lean the CONTROL board
in the direction of an arrow.
5 four screws
(BVTP3
(BVTP3
u 8)
2 two screws
(BVTP3
(BVTP3
u 8)
– Rear side view –
1 connector
(CN2518)
(CN2518)
2 connector
(CN2515)
(CN2515)
3 connector
(CN2701)
(CN2701)
4 Remove the CONTROL board
in the direction of an arrow.
5 CONTROL board
STR-DA2800ES
31
2-24. MAIN BLOCK-1
Ver. 1.2
• Abbreviation
CND : Canadian model
CND : Canadian model
0 two screws
(BVTP3
(BVTP3
u 8)
8 screw
(BV
(BV
S4
u 8)
qa bracket
(C-TW)
(C-TW)
9 bracket (VIDEO PWB)
bracket
(VIDEO PWB)
(VIDEO PWB)
5 connector
(CN310)
(CN310)
4 connector
(CN309)
(CN309)
6 connector
(CN1405)
(CN1405)
7 connector
(CNP54)
(CNP54)
lead pin
< Fig. W >
< Fig. X >
< Fig. U >
< Fig. V >
Wire setting
Wire setting
lead pin
STBY board
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
Note 4: Wire through the rear side than
the bracket (VIDEO PWB).
Note 2: The wire must not touch heat sink.
Note 2: The wire must not touch heat sink.
Note 2: The wire must not touch heat sink.
Note 3: The wire must not touch power transformer.
Note 3: The wire must not touch power transformer.
Note 3: The wire must not touch power transformer.
3 Cut the cable tie.
(See Fig. V)
cable tie
1 Remove wire from lead pin.
(See Fig. U)
1 Remove wire from two lead pins.
(See Fig. X)
1 Remove wire from
two lead pins. (See Fig. W)
1 Remove wire from lead pin.
(See Fig. U)
2 Remove wire from wiring stopper.
(See Fig. V)
wiring
stopper
stopper
3 Cut the cable tie.
(See Fig. V)
lead pin
lead pin
lead pin
lead pin
MAIN board
ACDC board
Note 3: The wire must not touch power transformer.
cable tie
Note 2: The wire must not touch heat sink.
GUIDE_B
board
board
GUIDE_A
board
board
GUIDE_B
board
board
wiring
stopper
stopper
(AEP)
(AEP)
(AEP)
Note 2: The wire must not touch heat sink.
cable tie
cable tie
cable tie
(AEP)
GUIDE_A
board
board
(US, CND)
(US, CND)
cable tie
lead pin
STR-DA2800ES
32
2-25. MAIN BLOCK-2
4 two screws
(BVTP3
(BVTP3
u 8)
4 two screws
(BVTP3
(BVTP3
u 8)
4 two screws
(BVTP3
(BVTP3
u 8)
3 two screws
(BV/ring)
(BV/ring)
5 main block
2 connector
(CN308)
(CN308)
1 Remove wire
from lead pin.
4 four screws
(BVTP3
(BVTP3
u 8)
– Rear side view –
lead pin
Wire setting
MAIN board
ACDC board
Note: The wire must not touch power transformer.
Click on the first or last page to see other STR-DA2800ES service manuals if exist.