Sony STR-DA2800ES Service Manual ▷ View online
STR-DA2800ES
13
2-3. DCDC BOARD-1
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
1 Cut the cable tie.
(See Fig. B)
1 Cut the cable tie.
(See Fig. B)
1 Cut the cable tie.
(See
(See
Fig.
A)
1 Cut the cable tie.
(See
(See
Fig.
A)
cable tie
3 clamp filter (ferrite core)
(FC3)
(FC3)
(See Fig. B)
4 connector
(CN1404)
(CN1404)
5 connector
(CN1401)
(CN1401)
6 connector
(CN1405)
(CN1405)
7 connector
(CN1406)
(CN1406)
clamp filter (ferrite core)
(FC3)
(FC3)
< Fig. B >
< Fig. A >
Wire setting
Note 3: The wire must not touch heat sink.
Note 2: The wire must not touch power transformer.
2 Remove wire from lead pin.
(See Fig. B)
cable tie
GUIDE_B board
DCDC
board
board
cable tie
clamp filter (ferrite core)
(FC3)
(FC3)
Note 3: The wire must not touch heat sink.
Note 2: The wire must not touch power transformer.
cable tie
GUIDE_B board
DCDC
board
board
(US, CND)
(AEP)
(US, CND)
(US, CND)
(US, CND)
(AEP)
(AEP)
(AEP)
• Abbreviation
CND : Canadian model
CND : Canadian model
Ver. 1.2
STR-DA2800ES
14
2-4. DCDC BOARD-2
5 two screws
(BVTP3
(BVTP3
u 8)
1 screw
(BVTP3
(BVTP3
u 8)
3 Remove the DCDC board block
in the direction of an arrow.
7 DCDC board
4 connector
(CN1403)
(CN1403)
1 screw
(BVTP3
(BVTP3
u 8)
2 claw
2 claw
5 two screws
(BVTP3
(BVTP3
u 8)
6 bracket (DC-F)
6 bracket (DC-F)
STR-DA2800ES
15
2-5. HAT BOARD
3 wire (flat type) (17 core)
(CN807)
(CN807)
6 HAT board
colored line
colored line
Insert is straight to the interior.
Insert is incline
wire (flat type)
wire (flat type)
connector
connector
OK
NG
Note 2: When installing the wire (flat type), ensure the colored line.
No slanting after insertion.
5 screw
(BVTP3
(BVTP3
u 8)
4 two nuts
(supplied with J861)
Note 1: In reassembling, use new binding band (taiton)
to fasten the clamp same as before.
1 Cut the binding band (taiton).
(See Fig. C)
J861 is not slanting.
OK
NG
Note 3: When installing the HAT board, check that J861 is
installed
installed
correctly.
J861 is slanting.
– Rear side view –
wiring stopper
HAT board
HAT board
SUB D-VIDEO board
binding band (taiton)
< Fig. C >
< Fig. D >
Wire setting
MAIN board
Note 4: The wire must not touch heat sink.
2 Remove wire from wiring stopper.
(See Fig. D)
STR-DA2800ES
16
2-6. SUB D-VIDEO BOARD BLOCK
8 Push two buttons of connector.
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
3 Cut the cable tie.
(See Fig. G)
qs SUB D-VIDEO
board
board
block
5 Remove wire from
wiring
wiring
stopper.
(See Fig. G)
7 HDMI cable (HDC1)
(CN3701)
(CN3701)
6 connector
(CN3571)
(CN3571)
9 flexible flat cable
(CN7001)
(CN7001)
4 tape
(See Fig. F)
2 wire (flat type) (17 core)
(CN807)
(CN807)
qa screw
(BVTP3
(BVTP3
u 8)
qa screw
(BVTP3
(BVTP3
u 8)
0 four screws
(B3
(B3
u 5)
colored line
colored line
Insert is straight to the interior.
Insert is incline
wire (flat type)
wire (flat type)
connector
connector
OK
NG
Note 2: When installing the wire (flat type), ensure the colored line.
No slanting after insertion.
– Rear side view –
cable tie
tape
wiring stopper
wiring stopper
HAT board
SUB D-VIDEO board
SUB D-VIDEO board
< Fig. E >
< Fig. G >
< Fig. F >
Wire setting
Note 3: The wire must not touch heat sink.
1 Remove wire from
wiring
wiring
stopper.
(See Fig. E)
Click on the first or last page to see other STR-DA2800ES service manuals if exist.