Sony NWZ-ZX1 Service Manual ▷ View online
NWZ-ZX1
32
2. Tap
“BATTERY”.
10:10
ServiceModeTool
COLOR
BATTERY
3. Confi rm that the following screen is displayed, and tap the
[RESET] button.
10:10
Push “Reset” button according to specifications.
Reset
ServiceModeTool
4. Confi rm that the “Reset success!” is displayed on the center of
screen.
10:10
Push “Reset” button according to specifications.
Reset
Reset success!
ServiceModeTool
5. Press the [
1
] button on “WALKMAN”, and confi rm that
screen on “WALKMAN” is turned off (sleep mode state).
display
[1] button
Note 1: Hold down the [
1
] button on “WALKMAN” by mistake, screen
on “WALKMAN” is turned Power off screen.
(The
following
fi gure is example of display)
When screen on “WALKMAN” is turned Power off screen, tap
the “
” (Back) button, and press the [
1
] button on “WALK-
MAN” again.
6. Remove the solder of three lead wires, and remove the lead
wires from the board. Next, solder the three lead wires to the
board, and confi rm that power supply of “WALKMAN” is
turned off.
board, and confi rm that power supply of “WALKMAN” is
turned off.
Three lead wires
NWZ-ZX1
33
7. Hold down the [
1
] button on “WALKMAN”, and confi rm that
“WALKMAN” boots up normally.
(The
following
fi gure is example of display)
[1] button
display
10:16
Wed, October 5
8. Connect PC and “WALKMAN” with the USB cable for the
WM-PORT (accessory).
USB cable
Plug in the USB cable
with facing upward,
making sure the
connection is secure.
with facing upward,
making sure the
connection is secure.
9. Confi rm that the USB connection screen is displayed on
“WALKMAN”, and confi rm that charge is performed normal-
ly.
ly.
Note 2: If the USB connection screen is not displayed, swipe the status bar
on the top of the screen then tap “USB connected” on the notifi ca-
tion panel.
tion panel.
USB storage in use
USB mass storage
6:09
Before turning off USB storage, unmount
(”eject”) your Android’s USB storage from
your computer.
Turn off USB storage
10. Assemble “WALKMAN” completely, and the confi rming is
completed.
Notes after mode completion:
Note 1: After work is completed, uninstall the service mode tool abso-
lutely.
(Refer to “3. UNINSTALLING METHOD OF THE SERVICE
MODE TOOL” on page 25 about procedure)
Note 2: When this unit connects with some site in order to perform the
operation check (When the connection with WiFi and the opera-
tion check of browser, etc. are performed etc.), the WiFi setting
list and the history of browser, etc. remain on this unit.
tion check of browser, etc. are performed etc.), the WiFi setting
list and the history of browser, etc. remain on this unit.
In that case, perform reset and initialization with reference to
page 4.
(When initialization is performed, all user informations are
cleared)
34
NWZ-ZX1
SECTION 4
EXPLODED VIEWS
1
X-2589-074-1 SVX
GRIP
ASSY
(Including Adhesive sheet, Speaker grill)
2
4-473-067-01 PLATE
(BOTTOM)
3
3-234-449-17 SCREW
(M1.4)
4
4-536-370-01 SCREW, 0+P2 1.4 POWERLOK
5
4-473-065-01 PANEL
(REAR)
6
4-480-024-01 CUSHION
(NAND)
7
4-489-286-01 SPACER
(NAND)
8
4-473-060-01 HOLDER
(CONNECTOR)
9
4-476-023-01 GASKET
(CONN)
10
4-538-017-01 HI-RES
LABEL
11
4-533-682-01 SHEET
(REAR_SIDE),
ADHESIVE
1000
9-913-402-43 POLYIMIDE SHEET (t=0.075) (for SERVICE)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
• Abbreviation
CH
CH
: Chinese model
CND : Canadian model
EE
EE
: East European model
4-1. PANEL (REAR) SECTION
• Rear view
EDWWHU\0$,1ERDUGVHFWLRQ
QRWVXSSOLHG
1
2
3
4
4
4
4
4
4
5
3
6
7
8
11
11
9
7
10
B
B
A
A
14.75
20.55
XQLWPP
3527(&7,216+((7
3$1(/B5($5
3$1(/B5($5
AERXW5HI1R
Please cut out and use POLYIMIDE SHEET for a specified
size when you exchange it for new parts.
Note: As for this part, the material or thickness might be
Please cut out and use POLYIMIDE SHEET for a specified
size when you exchange it for new parts.
Note: As for this part, the material or thickness might be
different compared with before.
However, there is no obstacle at all.
1000
3527(&7,216+((7
3$1(/B5($5
3$1(/B5($5
Ver. 1.1
35
NWZ-ZX1
4-2. BATTERY, MAIN BOARD SECTION
• Rear view
51
4-529-857-01 SPACER
(BATT)
52
4-475-089-01 SHEET
(BATT),
ADHESIVE
53
9-885-192-19 MAIN BOARD, COMPLETE (for SERVICE)
(Including EMMC board, GND fl exible board, Wire,
Shield) (EXCEPT CH) (See Note 2)
53
9-885-192-20 MAIN BOARD, COMPLETE (for SERVICE)
(Including EMMC board, GND fl exible board, Wire,
Shield) (CH) (See Note 2)
54
4-489-335-01 SHEET
(NAND),
ADHESIVE
55
4-473-064-01 SUPPORT
(BOTTOM)
56
3-234-449-63 SCREW
(M1.4)
57
4-489-653-01 SHEET
(SUPPORT_TOP),
ADHESIVE
58
4-473-063-01 COLLAR
(TOP)
59
4-480-463-01 CUSHION
(SHIELD)
60
4-533-683-02 CUSHION
(COIL)
61
4-534-128-01 SHEET, CAP FRONT LOWER
BAT1
A-1975-243-A BATTERY ASSY (Including Battery recycle label,
sheet (BATT)) (See Note 1)
FPC1
A-1975-246-A TP RELAY FPC ASSY
(Including TP relay fl exible board)
SP1
A-1975-244-A SPEAKER
BOX
ASSY
(Including NFC antenna, Speaker)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
51
52
53
56
57
58
58
61
59
56
56
FPC1
SP1
BAT1
A
EMMC board
MAIN board
antennastrap section
A
B
C
B
C
54
55
60
60
60
61
Note 1: When removing battery assy (Ref. No. BAT1) from the adhe-
sive sheet (BATT), it is not re-used. Be sure to exchange it for
new parts.
new parts.
When battery assy (Ref. No. BAT1) is replaced, refer to “4-3.
BATTERY” on page 31.
BATTERY” on page 31.
When the battery wire is removed, refer to “ABOUT THE
HANDLING OF THE BATTERY ASSY (BAT1)” on page 4.
HANDLING OF THE BATTERY ASSY (BAT1)” on page 4.
Note 2:
• The EMMC board or the MAIN board cannot exchange with single.
• The EMMC board or the MAIN board cannot exchange with single.
When exchanging the EMMC board or the MAIN board, exchange it
at the same time as the EMMC board and the MAIN board.
at the same time as the EMMC board and the MAIN board.
• When MAIN board is replaced, the data writing processing etc. are
necessary. For details, refer to “NOTE THE MAIN BOARD (IN-
CLUDING EMMC BOARD) REPLACING” on page 5.
CLUDING EMMC BOARD) REPLACING” on page 5.
• For the handling of the MAIN board, refer to “NOTE OF MAIN
BOARD HANDLING” on page 4.
Ver. 1.1
Click on the first or last page to see other NWZ-ZX1 service manuals if exist.