Sony NWZ-ZX1 Service Manual ▷ View online
NWZ-ZX1
17
2-8. SPEAKER BOX ASSY (SP1)
– Rear top view –
2 three screws (M1.4)
3 Remove the speaker box block
in the direction of the arrow.
1 two collars (top)
4 adhesive sheet
(support_top)
(support_top)
5 speaker box assy (SP1)
NWZ-ZX1
18
2-9. MAIN BOARD-1
•
Continued on 2-10 (page 19).
Note 1: Refer to “NOTE OF MAIN BOARD HANDLING” on page 4.
– Rear top view –
MAIN board
:LUHVHWWLQJ
[white/red]
[white]
[black (thin)]
LCD flexible board
3 Open the connector.
guide line
TP relay FPC assy
MAIN board
OK
NG
NG
Insert is shallow.
[black (thick)]
HP board
2 cushion
(shield)
(shield)
1 Remove four solders of wire.
4 SW flexible board
5 LCD flexible board
6 touch panel flexible board
MAIN board
center
3DVWLQJSRVLWLRQRIFXVKLRQVKLHOG
SW flexible board
cushion (shield)
,QVWDOOHGSRVLWLRQRI/&'IOH[LEOHERDUG
GND wire
two ribs
two grooves
OK
NG
Note 7: When installing the SW
flexible board, insert it
fully to the connector.
Inserted to fully.
Note 8:
There is a possibility of damaging LCD flexible board
when removing the direction of below figure of “NG”.
Note 9:
When installing LCD flexible board,
align two grooves and two ribs.
If putting into the connector shift
groove and rib, connector will be
broken.
Note 2: Do not fold the SW flexible board with tweezers.
Note 3: Do not pressing the SW flexible board with finger nails.
Note 4: When locking the connector, press the middle position
Note 3: Do not pressing the SW flexible board with finger nails.
Note 4: When locking the connector, press the middle position
of connector lever.
Note 5: Do not close the connector lever before the SW flexible
board
board
insertion.
Note 6: If the connector lever is closed, need to open
the connector lever fully, then insert the SW flexible
board and close the connector lever.
1RWHVIRUUHPRYLQJWKH/&'IOH[LEOHERDUG
NWZ-ZX1
19
2-10. MAIN BOARD-2
2-11. SW FPC ASSY (FPC2)
Note 1: When MAIN board is replaced, the data writing processing etc. are
necessary. For details, refer to “NOTE THE MAIN BOARD (IN-
CLUDING EMMC BOARD) REPLACING” on page 5.
CLUDING EMMC BOARD) REPLACING” on page 5.
The MAIN board cannot exchange with single. When exchanging
the MAIN board, exchange it at the same time as the EMMC board.
the MAIN board, exchange it at the same time as the EMMC board.
– Rear top view –
6 TP relay FPC assy
(FPC1)
(FPC1)
7 MAIN board
Note
Note
2:
Refer to “NOTE OF MAIN BOARD
HANDLING” on page 4.
1 Open the SW flexible board
in the direction of the arrow.
3 Remove the MAIN board block
in the direction of the arrow.
2 Peel off the MAIN board block from
the adhesive sheet (reset).
4 Open the connector.
5 TP relay flexible board
– MAIN board front top view –
Insert is shallow.
OK
NG
Note 3: When installing the TP relay flexible
board, insert it fully to the connector.
Inserted to fully.
– Rear top view –
Note 1:
When installing the SW FPC assy (FPC2),
align two bosses and two holes.
3 SW FPC assy (FPC2)
SW FPC assy (FPC2)
2 spacer (button)
2 spacer (button)
spacer (button)
guide line
guide line
spacer (button)
hole
hole
1 Peel off the adhesive sheet.
total six switches
total six buttons
two bosses
Note 2:
When installing the
SW FPC assy (FPC2),
align six buttons and
six
switches.
3DVWLQJSRVLWLRQRIWKHVSDFHUEXWWRQ
guide line
Ver. 1.1
NWZ-ZX1
20
2-12. ESCUTCHEON
2-13. BT/WIFI/GPS ANTENNA (ANT1)
– Rear top view –
protection sheet
(escutcheon)
(escutcheon)
guide line
escutcheon
5 escutcheon
,QVtaOOeG poVitioQ oI proteFtioQ VKeet eVFXtFKeoQ
hole
4 Draw out the escutcheon from hole.
guide line
1 two collars (bottom)
3 two screws (M1.4)
2 protection sheet
(escutcheon)
(escutcheon)
sheet (ANT)
guide line
guide line
BT/WIFI/GPS antenna (ANT1)
3DVWLQJSRVLWLRQRIVKHHW$17DQGVKHHW$17*
guide line
guide line
–5HDUWRSYLHZ–
4 cap (top)
2 Remove the cap (top) block
in the direction of the arrow.
1 Peel off the cap top upper sheet.
3 rib
3 rib
5 sheet (ANT)
6 sheet (ANT) G
7 BT/WIFI/GPS antenna
(ANT1)
(ANT1)
sheet (ANT) G
Click on the first or last page to see other NWZ-ZX1 service manuals if exist.