DOWNLOAD Sony NWZ-ZX1 Service Manual ↓ Size: 3.31 MB | Pages: 40 in PDF or view online for FREE

Model
NWZ-ZX1
Pages
40
Size
3.31 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
nwz-zx1.pdf
Date
PREV: Sony BDV-IZ1000W Service Manual

Sony NWZ-ZX1 Service Manual ▷ View online

NWZ-ZX1
13
SECTION  2
DISASSEMBLY
• 
This set can be disassembled in the order shown below.
2-1.  DISASSEMBLY  FLOW
2-10. MAIN BOARD-2
 (Page 
19)
2-11.  SW FPC ASSY (FPC2)
 (Page 
19)
SET
2-9. MAIN 
BOARD-1
 (Page 
18)
2-2. GRIP 
ASSY
 (Page 
14)
2-3.  PANEL (REAR) BLOCK
 (Page 
14)
2-4.  BATTERY ASSY (BAT1) WIRE
 (Page 
15)
2-5. BATTERY 
ASSY 
(BAT1)
 (Page 
15)
2-7.  SUPPORT (BOTTOM) BLOCK
 (Page 
16)
2-8.  SPEAKER BOX ASSY (SP1)
 (Page 
17)
2-6. EMMC 
BOARD
 (Page 
16)
2-12. ESCUTCHEON
 (Page 
20)
2-13. BT/WIFI/GPS ANTENNA (ANT1)
 (Page 
20)
2-14.  LCD MODULE (LCD1)
 (Page 
21)
2-15. HP BOARD
 (Page 
22)
NWZ-ZX1
14
2-3.  PANEL (REAR)  BLOCK
Note: Follow the disassembly procedure in the numerical order given.
2-2. GRIP 
 
ASSY
– Rear top view –
1 label (model) number
Note 1: When removing the label (model) number, 
 
carefully peel it off of the unit, and then 
 
reapply it after assembling the unit.
2 Peel off the adhesive sheet.
3 grip assy
 Note 
2: When removing grip assy, it is not re-used.
 
 
Be sure to exchange it for new parts.
3 two screws
  (P2 1.4 POWERLOK)
2 plate (bottom)
4 Peel off the panel (rear) block from 
 
the adhesive sheet (support_top).
1 two screws
 (M1.4)
3 four screws
  (P2 1.4 POWERLOK)
5 Peel off the adhesive sheet (rear_side).
5 Peel off the adhesive sheet (rear_side).
6 panel (rear) block
– Rear top view –
Ver. 1.1
NWZ-ZX1
15
2-5.  BATTERY  ASSY (BAT1)
2-4.  BATTERY  ASSY (BAT1)  WIRE
1 Remove three solders of battery wire.
 Note 
3:
 When the battery wire is removed, refer to 
 
 
“ABOUT THE HANDLING OF 
 
 
THE BATTERY ASSY (BAT1)” on page 4.
– Rear top view –
MAIN board
‡ %atter\ aVV\ %$7 wire VettiQJ
[red]
[white]
[black]
battery assy (BAT1)
Note 1: Make sure to remove three solders of battery wires before 
 
disassembling the mechanical common block.
 
Moreover, when removing solders, remove solder after 
 
turning off a mechanical common block.
Note 2: When replacing some mounted board or electrical parts, 
 
soldering three battery wires after all wirings are connected.
A
B
– Rear top view –
3 spacer (BATT)
spacer (BATT)
guide line
guide line
guide line
guide line
2 Remove the battery block 
 
in the direction of the arrow. 
battery assy (BAT1)
‡3DVWLQJSRVLWLRQRIVSDFHU%$77
Note 2: When installing the battery assy (BAT1), push 
 
firmly the battery assy (BAT1) until it is put 
 
together to guidelines in order of the arrows 
 
A
 and 
B
. 
battery assy 
(BAT1)
MAIN board
4 battery assy (BAT1)
 Note 
1:
 When removing battery assy (BAT1) from 
 
 
the adhesive sheet (BATT), it is not re-used.
 
 
Be sure to exchange it for new parts.
1 Peel off the battery block from 
 
the adhesive sheet (BATT).
 Note 
1:
 When removing battery assy (BAT1) from 
 
 
the adhesive sheet (BATT), it is not re-used.
 
 
Be sure to exchange it for new parts.
NWZ-ZX1
16
2-6.  EMMC  BOARD
2-7.  SUPPORT (BOTTOM)  BLOCK
Note 1: The EMMC board cannot exchange with single. When ex-
changing the EMMC board, exchange it at the same time as 
the MAIN board.
– Rear top view –
3 adhesive sheet (NAND)
2 Remove the EMMC board block 
 
in the direction of the arrow. 
1 connector
 Note 
2:
 When removing the connector, 
 
 
please lift vertically the EMMC board.
4 EMMC board
– Rear top view –
3 support (bottom) block
MAIN board
support (bottom)
‡ +ow to iQVtaOO oI VXpport EottoP EOoFN
Note:
 When installing the support (bottom) block, 
 
please insert the flexible board block 
 
in the hole of support (bottom).
1 claw
2 claw
flexible board block
hole
Page of 40
Display

Click on the first or last page to see other NWZ-ZX1 service manuals if exist.

RANDOM: