Sony NWZ-F885 / NWZ-F886 / NWZ-F887 Service Manual ▷ View online
NWZ-F885/F886/F887
17
2-7. BATTERY ASSY (BAT1)
A
B
– Rear bottom view –
2 adhesive sheet (BATT)
adhesive sheet
(BATT)
(BATT)
guide line
guide line
guide line
guide line
1 Remove the battery assy (BAT1)
in the direction of an arrow.
battery assy (BAT1)
Adhesive sheet (BATT) setting
Battery assy (BAT1) setting
3 battery assy (BAT1)
Note
1: When removing battery assy (BAT1) from
the adhesive sheet (BATT), it is not reused.
Replace it with a new part always.
Note 2: When installing the battery assy (BAT1), push
firmly the battery assy (BAT1) until it is put
together to guidelines in order of the arrows
A
and
B
.
Note 3: The adhesive sheet (BATT) has been changed
to large in the midway of production.
Therefore, it can not be pasted on the inside of
the
guidelines.
2-8. ESCUTCHEON
(WM)
2 claw
3 escutcheon (WM)
– Rear bottom view –
1 two screws (0+Z B1.4)
Note: When installing the screws (0+Z B1.4), since it is easy to damage
Note: When installing the screws (0+Z B1.4), since it is easy to damage
the tapped hole of escutcheon (WM), install carefully.
tightening torque : 0.04 1m 0.00 1m
Ver. 1.1
NWZ-F885/F886/F887
18
2-9. MAIN BOARD
CN1001
CN1001
OK
NG
A
OK
NG
NG
– Rear bottom view –
1 Insert thin tweezers etc. in the hole of the
HP flexible board and remove it straightly
from the connector.
HP flexible board
HP flexible board
Note 1: CN1001 is not have a connector lever.
Do not lift up the connector.
Note 2: When installing the HP flexible board,
insert thin tweezers etc. in the hole of the
HP flexible board and insert it straightly
to the inside of connector.
Note 3: When installing the HP flexible board,
insert it fully to the connector.
Insert is shallow.
Inserted to fully.
9 MAIN board
Note 7:
When installing the MAIN board,
align two ditches and two screw holes.
4 Remove the LCD flexible board
in the direction of arrow
B.
(CN6101)
3 Remove the touch panel flexible
board in the direction of arrow
A.
(CN6001)
2 HP flexible board
(CN1001)
(CN1001)
5 spacer module
6 claw
7 boss
7 boss
Note 5:
There is a possibility of damaging LCD flexible board when
removing the direction of below figure of “NG”.
B
Note 6:
When installing LCD flexible board, align two ditches and
two
ribs.
If putting into the connector shift ditch and rib, connector
will be broken.
two ditches
two ribs
screw hole
screw hole
ditch
8 Draw out the WM-PORT from the hole.
ditch
Note 4: The terminal of the connector may be
damaged if the HP flexible board is
inserted
forcibly.
Insert in the loading slot of the connector,
without applying impossible power.
NWZ-F885/F886/F887
19
2-10. 5 PIN HP ASSY (HPJ1)
1 screw (M1.4)
3 claw
– Rear top view –
– Rear view –
2 Move the 5 pin HP assy
block in the direction of
an
arrow.
4 Remove the 5 pin HP assy block
in the direction of an arrow.
5 holder (HP)
6 5 pin HP assy
(HPJ1)
(HPJ1)
5 pin HP assy block
bottom side
NWZ-F885/F886/F887
20
2-11. BT/WIFI/GPS ANTENNA (ANT1)
1 boss
– Rear bottom view –
2 BT/WIFI/GPS antenna
(ANT1)
(ANT1)
Click on the first or last page to see other NWZ-F885 / NWZ-F886 / NWZ-F887 service manuals if exist.