Sony NWZ-F885 / NWZ-F886 / NWZ-F887 Service Manual ▷ View online
NWZ-F885/F886/F887
13
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. CAP
(REAR)
2-10. 5 PIN HP ASSY (HPJ1)
(Page
(Page
19)
2-11. BT/WIFI/GPS ANTENNA (ANT1)
(Page
(Page
20)
SET
2-9. MAIN
BOARD
(Page
18)
2-2. CAP
(REAR)
(Page
13)
2-3. CAP (TOP) BLOCK
(Page
(Page
14)
2-4. CACE (REAR) BLOCK
(Page
(Page
14)
2-5. SPEAKER BOX ASSY (SP1)
(Page
(Page
15)
2-7. BATTERY
ASSY
(BAT1)
(Page
17)
2-8. ESCUTCHEON
(WM)
(Page
17)
2-6. WIRE OF BATTERY ASSY (BAT1)
(Page
(Page
16)
6 cap (rear)
4 claw
4 claw
– Rear top view –
3 Remove the cap (rear) in the direction of an arrow.
JIG
When disassembling the set, use the following jig.
When disassembling the set, use the following jig.
Part No.
Description
9-913-402-33 Tool for Disassembling
5 adhesive sheet (cap rear)
Note 4: The sheet (cap rear) is not reused.
Replace it with a new part always.
adhesive sheet
(cap rear)
(cap rear)
cap (rear)
cap (top)
1 Insert the jig in the crevice between the cap (rear) and
the cap (top), and lift the cap (rear) gradually.
Note 1: Work by applying load to the cap (rear) side not to
Note 1: Work by applying load to the cap (rear) side not to
damage a cap (top).
Note 2: Since the portion of NFC may be damaged if a jig
is inserted deeply, insert carefully.
2 Make it move in the direction of an arrow,
and remove adhesion sheet (cap rear).
Note 3: The sheet (cap rear) is not reused.
Note 3: The sheet (cap rear) is not reused.
Replace it with a new part always.
NWZ-F885/F886/F887
14
2-3. CAP (TOP) BLOCK
2-4. CASE (REAR) BLOCK
1 two screws
(0+Z
(0+Z
B1.4)
– Rear top view –
ribs
holes
2 cap (top) block
Note: When installing the cap (top) block,
Note: When installing the cap (top) block,
align two holes and two ribs.
1 two screws
(0+Z
(0+Z
B1.4)
2 two screws
(M1.4)
(M1.4)
– Front bottom view –
3 Remove the common block in
the direction of an arrow.
common block
4 Draw out the WM-PORT and
the strap holder from holes
of the case (rear) block.
5 case (rear) block
strap holder
WM-PORT
Note 2: When installing the case (rear) block,
check that the hole of the strap holder
is not blocked.
Note 1: When installing the common block to the
case (rear) block, switches may be damaged
where a button is pushed.
Check that the button is not pushed.
NWZ-F885/F886/F887
15
2-5. SPEAKER BOX ASSY (SP1)
2 screw (M1.4)
2 screw (M1.4)
1 spacer (shield)
spacer (shield)
6SDFHUVKLHOGVHWWLQJ
battery assy (BAT1)
MAIN board
guide line
3 Lift up the speaker box
assy in the direction of
an
arrow.
CN1201
CN1201
OK
NG
4 Insert thin tweezers etc. in the hole of the
speaker flexible board and remove it
straightly from the connector.
speaker flexible board
speaker flexible board
5 speaker flexible board
(CN1201)
(CN1201)
6 speaker box assy
(SP1)
(SP1)
Note 1: CN1201 is not have a connector lever.
Do not lift up the connector.
Note 2: When installing the speaker flexible board,
insert thin tweezers etc. in the hole of the
speaker flexible board and insert it
straightly to the inside of connector.
Note 3: When installing the speaker flexible board,
insert it fully to the connector.
Note 4: The terminal of the connector may be
damaged if the speaker flexible board
is inserted forcibly.
Insert in the loading slot of the connector,
without applying impossible power.
Insert is shallow.
Inserted to fully.
–5HDUERWWRPYLHZ–
NWZ-F885/F886/F887
16
2-6. WIRE OF BATTERY ASSY (BAT1)
Note 1: Make sure to remove three solders of battery wires before
disassembling the mechanical common block.
Moreover, when removing solders, remove solder after
turning off a mechanical common block.
Note 2: When replacing some mounted board, soldering three
battery wires after all wirings other than speaker flexible
board are connected.
– Rear bottom view –
%atter\ wire VettiQJ
1 Remove three solders of battery wire.
Note 3:
When the wire of battery assy (BAT1) is removed,
refer to “ABOUT THE HANDLING OF THE
BATTERY ASSY (BAT1)” on page 4.
[red]
[white]
[black]
MAIN board battery assy
(BAT1)
Click on the first or last page to see other NWZ-F885 / NWZ-F886 / NWZ-F887 service manuals if exist.