Sony HCD-SLK10D / HCD-SLK20D / WHG-SLK10D / WHG-SLK20D Service Manual ▷ View online
HCD-SLK10D/SLK20D
13
2-6. DMB19 BOARD BLOCK-2
2-7. DMB19 BOARD
– Rear bottom view –
Note 1: Please spread a sheet under a unit
not to injure front panel.
4 wire (flat type) (13 core)
(CN1109)
1 two hooks
2
3 connector
(CN201)
6 DMB19 board block
5 connector (CN1105)
Note
2: When you remove the connector,
it is necessary to note it because
it is very hard.
Note 3: When you install the wire (flat type), please
install them correctly.
There is a possibility that this machine damages
when not correctly installing it.
Insert is straight
to the interior.
to the interior.
connector
Insert is incline.
wire
(flat type)
(flat type)
wire
(flat type)
(flat type)
connector
OK
NG
Note 4: Do not insert the wire (flat type) in the same amount of
connector by mistake. Refer to
“2-21. HOW TO BEND
WIRE
(FLAT
TYPE)” (page 24) and “5-1. FLAME
PRINTED WIRING BOARDS” (page 31) for details.
– DMB19 board block rear bottom view –
1 four screws
(BV3)
3 holder (DMB)
5 DMB19 board
DMB19 board
tape
2
4 wire (flat type) (7 core)
(CN202)
wire (flat type) (7 core)
:ire VettiQJ
Note 1: When you install the wire (flat type), please
install them correctly.
There is a possibility that this machine damages
when not correctly installing it.
Insert is straight
to the interior.
to the interior.
connector
Insert is incline.
wire
(flat type)
(flat type)
wire
(flat type)
(flat type)
connector
OK
NG
Note 2: Do not insert the wire (flat type) in the same amount of
connector by mistake. Refer to
“2-21. HOW TO BEND
WIRE
(FLAT
TYPE)” (page 24) and “5-1. FLAME
PRINTED WIRING BOARDS” (page 31) for details.
HCD-SLK10D/SLK20D
14
2-8. HOLDER (JACK) BLOCK
– Rear bottom view –
Note 1: Please spread a sheet under a unit
not to injure front panel.
2 wire (flat type)
(7
core)
(CN705)
1 Lift up the lead pin.
7 holder (jack) block
6 screw
(BVTP2.6)
3 Lift up the
clamp
(L35).
4 connector
(SLK10D:
CN601/
SLK20D:
CN603)
5 connector
(SLK10D:
CN602/
SLK20D:
CN604)
:ire VettiQJ
lead pin
80 mm
TERMINAL board
TERMINAL board
tape
filter clamp (ferrite core)
lead pin
clamp (L35)
JACK board
tape
filter clamp
(ferrite core)
(ferrite core)
cover (CDM) 86S
cover (CDM) 86S
Note 2: When you install the wire (flat type), please
install them correctly.
There is a possibility that this machine damages
when not correctly installing it.
Insert is straight
to the interior.
to the interior.
connector
Insert is incline.
wire
(flat type)
(flat type)
wire
(flat type)
(flat type)
connector
OK
NG
Note 3: Do not insert the wire (flat type) in the same amount of
connector by mistake. Refer to
“2-21. HOW TO BEND
WIRE
(FLAT
TYPE)” (page 24) and “5-1. FLAME
PRINTED WIRING BOARDS” (page 31) for details.
HCD-SLK10D/SLK20D
15
2-9. MD BLOCK
2-10. POWER BLOCK
– Rear bottom view –
Note 1: Please spread a sheet under a unit
not to injure front panel.
2 wire (flat type) (9 core)
(CN703)
ditches
ditches
ditches
1
3 MD block
Note
2: When you installing the cover (CDM)
block, match the position of three
ditches.
Note 3: When you install the wire (flat type), please
install them correctly.
There is a possibility that this machine damages
when not correctly installing it.
Insert is straight
to the interior.
to the interior.
connector
Insert is incline.
wire
(flat type)
(flat type)
wire
(flat type)
(flat type)
connector
OK
NG
Note 4: Do not insert the wire (flat type) in the same amount of
connector by mistake. Refer to
“2-21. HOW TO BEND
WIRE
(FLAT
TYPE)” (page 24) and “5-1. FLAME
PRINTED WIRING BOARDS” (page 31) for details.
2 screw
(BVTP2.6)
3 clamp (L35)
3 clamp (L35)
2 screw
(BVTP2.6)
1 connector
(CN900)
4 power block
– Rear bottom view –
Note: Please spread a sheet under a unit
not to injure front panel.
MAIN board
:ire VettiQJ
clamp (L35)
bottom side
HCD-SLK10D/SLK20D
16
2-11. SWITCHING REGULATOR (SWR1)
3RZHUFRUGVHWWLQJ
switching regulator
(SWR1)
(SWR1)
bottom side
tape
filter clamp (ferrite core)
power cord
power cord
100 mm
–3RZHUEORFNUHDUERWWRPYLHZ–
2
1 two screws
(BVTP3
u 8)
4 connector
(CN2)
5 power cord connector
(CN1)
6 switching regulator
(SWR1)
3 shield case (power)
Note: When you install the shield case (power),
confirm the position of the ditch.
Click on the first or last page to see other HCD-SLK10D / HCD-SLK20D / WHG-SLK10D / WHG-SLK20D service manuals if exist.