Sony HCD-SLK10D / HCD-SLK20D / WHG-SLK10D / WHG-SLK20D Service Manual ▷ View online
HCD-SLK10D/SLK20D
17
2-12. DISPLAY BOARD BLOCK
4 four screws
(BVTP2.6)
2 connector
(CN900)
3 LCD flexible board
(CN406)
1 Lift up the lead pin.
lead pin
MAIN board
MAIN board
tape
tape
– Rear bottom view –
Note 1: Please spread a sheet under a unit
not to injure front panel.
5
6 wire (flat type) (9 core)
(CN606)
7 wire (flat type) (11 core)
(CN408)
8 DISPLAY board block
DISPLAY board
:ire VettiQJ
DISPLAY board
– )roQt SaQeO iQQer view –
Note 2: When you install the wire (flat type), please
install them correctly.
There is a possibility that this machine damages
when not correctly installing it.
Insert is straight
to the interior.
to the interior.
connector
Insert is incline.
wire
(flat type)
(flat type)
wire
(flat type)
(flat type)
connector
OK
NG
Note 3: Do not insert the wire (flat type) in the same amount of
connector by mistake. Refer to
“2-21. HOW TO BEND
WIRE
(FLAT
TYPE)” (page 24) and “5-1. FLAME
PRINTED WIRING BOARDS” (page 31) for details.
HCD-SLK10D/SLK20D
18
2-13. DISPLAY BOARD
1 three screws
(BVTP2.6)
2 holder (PWB DISPLAY)
holder (PWB DISPLAY)
3 cushion (WH)
6 connector
(CN405)
7 connector
(CN602)
8 ground plate (USB)
– DISPLAY board block rear bottom view –
4 wire (flat type) (7 core)
(CN604)
5 wire (flat type) (5 core)
(CN605)
9 DISPLAY board
DISPLAY board
Note 1: When you install the wire (flat type), please
install them correctly.
There is a possibility that this machine damages
when not correctly installing it.
Insert is straight
to the interior.
to the interior.
connector
Insert is incline.
wire
(flat type)
(flat type)
wire
(flat type)
(flat type)
connector
OK
NG
tape
:ire VettiQJ
– DISPLAY board block iQQer view –
tape
Note 2: Do not insert the wire (flat type) in the same amount of
connector by mistake. Refer to
“2-21. HOW TO BEND
WIRE
(FLAT
TYPE)” (page 24) and “5-1. FLAME
PRINTED WIRING BOARDS” (page 31) for details.
HCD-SLK10D/SLK20D
19
2-14. MAIN BOARD-1
MAIN board
:LUHVHWWLQJ
Note 3: When you install the wire (flat type), please
install them correctly.
There is a possibility that this machine damages
when not correctly installing it.
Insert is straight
to the interior.
to the interior.
connector
Insert is incline.
wire
(flat type)
(flat type)
wire
(flat type)
(flat type)
connector
OK
NG
–5HDUERWWRPYLHZ–
1 Lift up two lead pins.
1 Lift up the lead pin.
qa Lift up the clamp (L35).
clamp (L35)
2 wire (flat type) (7 core)
(CN103)
3 wire (flat type) (9 core)
(CN301)
7 wire (flat type) (9 core)
(CN105)
4 wire (flat type) (11 core)
(CN101)
8 wire (flat type) (11 core)
(CN302)
0 wire (flat type) (11 core)
(CN109)
5 wire (flat type) (5 core)
(CN305)
6 wire (flat type) (13 core)
6 wire (flat type) (13 core)
(CN102)
9 connector (CN107)
Note
2: When you remove the connector, it is necessary
to note it because it is very hard.
qs connector
(CN900)
Note 1: Please spread a sheet under a unit
not to injure front panel.
Note 4: Do not insert the wire (flat type) in the same amount of
connector by mistake. Refer to
“2-21. HOW TO BEND
WIRE
(FLAT
TYPE)” (page 24) and “5-1. FLAME
PRINTED WIRING BOARDS” (page 31) for details.
:LUHVHWWLQJ
wire (flat type) (5 core)
tape
:LUHVHWWLQJ
lead pin
lead pin
lead pin
KEY_LEFT board
LOGO board
MAIN board
MAIN board
MAIN board
HP board
bottom side
HCD-SLK10D/SLK20D
20
2-15. MAIN BOARD-2
2-16. LCD MODULE (LCD901)
– Rear bottom view –
4 Lift up the lead pin.
1 connector
(CN241)
6 cushion (FPC)
5 connector
(CN901)
2 three screws
(BVTP3
u 8)
2 three screws
(BVTP3
u 8)
7 two screws
(BVTP3
u 8)
8 heat sink (AMP)
9 MAIN board
3
Note: Please spread a sheet under a unit
not to injure front panel.
MAIN board
:ire VettiQJ
KEY_RIGHT board
KEY_LEFT board
LOGO board
tape
tape
:LUHVHWWLQJ
3
4 LCD module
(LCD901)
–5HDUERWWRPYLHZ–
1 four screws
(BVTP2.6)
2 bracket (LCD)
Note: Please spread a sheet under a unit
not to injure front panel.
wire (flat type) (5 core)
–)URQWSDQHOLQQHUYLHZ–
Click on the first or last page to see other HCD-SLK10D / HCD-SLK20D / WHG-SLK10D / WHG-SLK20D service manuals if exist.