Sony HCD-PZ1D / MHC-PZ1D Service Manual ▷ View online
HCD-PZ1D
5
VIDEO SIGNAL CONFIRMATION METHOD
This unit can display the video of the connected cyber shot on the
LCD module.
Execute the method of the following when the defective video sig-
nal unit is brought in, and judge whether the main unit or Party-
shot & cyber shot is defective.
This unit can display the video of the connected cyber shot on the
LCD module.
Execute the method of the following when the defective video sig-
nal unit is brought in, and judge whether the main unit or Party-
shot & cyber shot is defective.
Procedure:
1. Prepare the jig (Part No. 1-771-264-11).
1. Prepare the jig (Part No. 1-771-264-11).
pin 3
(VIDEO GND)
(VIDEO GND)
Note:
Connect pin 2 between
pin 3 with the lead wire.
Connect pin 2 between
pin 3 with the lead wire.
pin 2
(GND)
(GND)
pin 4
(VIDEO SIGNAL)
(VIDEO SIGNAL)
pin 1
(POWER SUPPLY)
+4.2 V ± 0.15 V
(POWER SUPPLY)
+4.2 V ± 0.15 V
jig
2. Turn LOCK RING in the direction of [PLUG IN].
LOCK RING
POWER PLUG
3. Attach the jig with the POWER PLUG.
JIG
4. Keep pushing the SHUTTER (A) on, and turn LOCK RING in
the direction of [LOCK].
SHUTTER (A)
LOCK RING
5. Press the [Party-shot SYNC] button.
6. Confi rm the voltage between pin 1 (POWER SUPPLY) and
pin 2 (GND) of jig is a standard value.
Standard
value:
[Party-shot SYNC] indicator lighting : +4.2 V ± 0.15 V
[Party-shot SYNC] indicator blinking : +4.8 V ± 0.15 V
When [Party-shot SYNC] indicator is turned off : 0 V
7. Input the video signal (composite video out signal from DVD
player etc.) between pin 3 (VIDEO GND) and pin 4 (VID-
EO SIGNAL), and confi rm the video is displayed on the LCD
module.
EO SIGNAL), and confi rm the video is displayed on the LCD
module.
HCD-PZ1D
6
PARTY-SHOT SERVICE POSITION
LCD CTRL BOARD SERVICE POSITION
DMB19 BOARD SERVICE POSITION
AMP BOARD SERVICE POSITION
Note: Set up the unit to lay it down sideway.
MAIN board
Digital still camera
Intelligent pantilter
(IPT-DS2)
(IPT-DS2)
– Bottom view –
DMB19 board
DMB19 board
– Rear view –
LCD CTRL board
MAIN board
AMP board
TRANSFORMER
board
board
TRANS-SUB board
sheet
front panel
HCD-PZ1D
7
NOTE OF REPLACING THE IC401 ON THE AMP BOARD
The IC401 is limited to the stock quantity of service parts.
When the IC401 cannot be obtained, exchange the complete AMP
board.
However, when the complete AMP board is exchanged, you must
also exchange the IC501 on the MAIN board to Type B at the same
time.
Refer to following fl owchart.
The IC401 is limited to the stock quantity of service parts.
When the IC401 cannot be obtained, exchange the complete AMP
board.
However, when the complete AMP board is exchanged, you must
also exchange the IC501 on the MAIN board to Type B at the same
time.
Refer to following fl owchart.
Repair start
Repair comfirmation
of IC401
IC401 exchange
Complete AMP
board exchange
IC501 on the
MAIN board
exchange to Type B
Operation check
Part procurement
of IC401
NG
OK
Repair completion
Ver. 1.2
HCD-PZ1D
8
MANUAL OPENING AND CLOSING THE DVD TRAY
As illustrated, insert a fl at-head screwdriver and give a turn to the left to put the tray out.
As illustrated, insert a fl at-head screwdriver and give a turn to the left to put the tray out.
NOTE FOR REPLACEMENT OF THE KNOB (JOG)
When replacing the KNOB (JOG), apply the SANKOL FTA-001HA (Part No. J-2501-264-A) to the end of the rib at 6 places.
When replacing the KNOB (JOG), apply the SANKOL FTA-001HA (Part No. J-2501-264-A) to the end of the rib at 6 places.
NOTE FOR REPLACEMENT OF THE HOLDER (KNOB)
When replacing the HOLDER (KNOB), apply the SANKOL FG-21BL (Part No. J-2501-251-A) to the end of the SPRING (KNOB)
at 2 places after the SPRING (KNOB) is installed.
When replacing the HOLDER (KNOB), apply the SANKOL FG-21BL (Part No. J-2501-251-A) to the end of the SPRING (KNOB)
at 2 places after the SPRING (KNOB) is installed.
SANKOL FTA-001HA
knob (JOG)
SANKOL FTA-001HA
SANKOL FG-21BL
SANKOL FG-21BL
holder (knob)
spring (knob)
1
Insert a tapering driver into the
hole of the chassis, and turn it
in the direction of the arrow A.
in the direction of the arrow A.
A
2
tray
– Bottom view –
Click on the first or last page to see other HCD-PZ1D / MHC-PZ1D service manuals if exist.