Sony HCD-PZ1D / MHC-PZ1D Service Manual ▷ View online
HCD-PZ1D
9
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-5. BASE
PLATE
(Page
11)
2-6. CAM RING (SHUTTER)
(Page
(Page
12)
2-7. TORSION SPRING (A)
(Page
(Page
12)
2-8. RING
(OPERATING)
(Page
13)
2-22. BACK PANEL
BLOCK
(Page
BLOCK
(Page
22)
2-13. RIGHT BOARD,
LEFT
LEFT
BOARD
(Page
16)
2-11. FRONT PANEL BLOCK
(Page
(Page
15)
2-12. VOL-LED BOARD
(Page
(Page
16)
2-23. MAIN BOARD
(Page
(Page
23)
2-25. VIDEO BOARD
(Page
(Page
25)
2-24. AMP BOARD
(Page
(Page
24)
2-15. LCD CTRL BOARD
(Page
(Page
17)
2-19. BU HOLDER BLOCK
(Page
(Page
20)
2-20. DMB19 BOARD
(Page
(Page
21)
2-21. OPTICAL PICK-UP
(KHM-313CAB)
(Page
(KHM-313CAB)
(Page
21)
2-17. SUB PANEL LCD
BLOCK
(Page
BLOCK
(Page
19)
2-18. LCD MODULE
(LCD101)
(Page
(LCD101)
(Page
19)
2-14. FRONT BOARD
(Page
(Page
17)
2-16. MIC BOARD
(Page
(Page
18)
2-26. MECHANISM DECK
(CDM74HFV
(CDM74HFV
ASSY)
(Page
25)
2-28. SENSOR BOARD
(Page
(Page
26)
2-27. DRIVER BOARD,
SW
SW
BOARD
(Page
26)
2-29. MOTOR (TB) BOARD
(Page
(Page
27)
2-30. MOTOR (LD) BOARD
(Page
(Page
27)
2-9. CHASSIS
BLOCK
(Page
13)
2-10. LOADING PANEL
(Page
(Page
14)
2-4. CORD
(WITH PLUG) (J1)
(Page
11)
SET
2-3. TOP PANEL BLOCK
(Page
(Page
10)
2-2. CASE (SIDE L),
CASE (SIDE L)
(Page
10)
HCD-PZ1D
10
2-3. TOP PANEL BLOCK
Note: Follow the disassembly procedure in the numerical order given.
2-2. CASE (SIDE L), CASE (SIDE R)
5
case (side L)
5
case (side R)
1
three screws
(case
M3
u6)
1
three screws
(case
M3
u6)
3
3
4
4
2
three screws
(BVTP
3
u8)
2
three screws
(BVTP
3
u8)
3
screw
(BVTP
3
u8)
9
top panel block
4
claw
5
two hooks
4
claw
3
screw
(BVTP
3
u8)
3
screw
(BVTP
3
u8)
1
Lift up the lead pin.
2
connector
(CN410)
8
connector
(CN954)
7
connector
(CN953)
1
Lift up the lead pin.
6
front side
lead pin
lead pin
:LUHVHWWLQJ
AMP board
heat sink
clamp filter
clamp filter
AMP board
OK
NG
heat sink
HCD-PZ1D
11
2-4. CORD (WITH PLUG) (J1)
2-5. BASE PLATE
1
clamp filter
1
Set marking of the cord (with plug) (J1)
to the position of figure.
2
Roll the code (with plug) (J1) once at
filter
clamp.
3
Paste the tape as shown in figure.
marking
3
cord (with plug) (J1)
2
&ODPSILOWHUVHWWLQJ
– Bottom view –
1
1
2
two screws
(BVTP 2.6 (3CR))
2
two screws
(BVTP 2.6 (3CR))
3
base plate
base plate
rear side
:iUe VettiQJ
:iUe VettiQJ
base plate
JUNC board
Note: When you install the base plate, install it
so that the hook may become front side.
front side
HCD-PZ1D
12
2-6. CAM RING (SHUTTER)
2-7. TORSION SPRING (A)
– Bottom view –
1
three screws
(BVTP 2.6 (3CR))
2
cam ring (elevator)
arrow mark of cam ring (elevator)
arrow mark of cam ring (shutter)
arrow mark of top panel
5
cam ring (shutter)
3
stage (plug)
4
three compression springs
Note: When you install the cam ring (elevator) and the cam
ring (shutter), set the position of each arrow mark to
the position of the arrow mark of the top panel.
1
shutter (A) shaft
shutter (A) shaft
2
torsion spring (A)
7RUVLRQVSULQJ$VHWWLQJ
–%RWWRPUHDUYLHZ–
torsion spring (A)
ditch of top panel
rear side
Click on the first or last page to see other HCD-PZ1D / MHC-PZ1D service manuals if exist.