Sony HCD-PZ1D / MHC-PZ1D Service Manual ▷ View online
HCD-PZ1D
13
2-9. CHASSIS BLOCK
2-8. RING
(OPERATING)
PLUG IN
RELEASE
Note: When you install the ring (operating), set the position
of mark of the ring (operating) to the position of the
RELEASE mark of the top panel.
1
claw
1
claw
2
ring (operating)
RELEASE mark of top panel
mark of ring (operating)
1
screw
(BVTP
3
u8)
1
two screws
(BVTP
3
u8)
1
two screws
(BVTP
3
u8)
3
chassis block
2
– Bottom view –
HCD-PZ1D
14
2-10. LOADING PANEL
– Bottom view –
4
loading panel
3
four claws
1
Insert a tapering driver into the
hole of the chassis, and turn it
in the direction of the arrow A.
in the direction of the arrow A.
2
A
HCD-PZ1D
15
2-11. FRONT PANEL BLOCK
4
wire (flat type) (7 core)
(CN503)
3
connector (CN002)
7
connector (CN1105)
DMB19 board
tape
WIRE HOLDER A board
6
connector
(CN407)
8
qs
screw
(BVTP
3
u8)
qs
screw
(BVTP
3
u8)
qs
three screws
(BVTP
3
u8)
9
screw
(BVTP 2.6 (3CR))
qa
lug wire
qa
lug wire
qa
lug wire
0
screw
(BVTP
3
u8)
0
screw
(BVTP
3
u8)
2
flexible flat cable (21 core)
(CN501)
5
flexible flat cable (5 core)
(CN101)
qd
front panel block
1
Lift up seven lead pins.
1
Lift up the lead pin.
AMP board
AMP board
front side
front side
MAIN board
MAIN board
AMP board
rear side
front side
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
flexible
cable
cable
connector
flexible
cable
cable
OK
NG
Note: When you install the flat cable, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
:LUHVHWWLQJ
:LUHVHWWLQJ
:LUHVHWWLQJ
–%RWWRPYLHZ–
front side
lead pin
lead pin
lead pin
lead pin
lead pin
lead pin
lead pin
lead pin
HCD-PZ1D
16
2-12. VOL-LED BOARD
2-13. RIGHT BOARD, LEFT BOARD
Note: Even if RIGHT board is not removed, LEFT board can be removed.
hole
1
Push the knob (VOL) assy
by flat-head screwdriver.
– Inner view –
2
knob (VOL) assy
6
VOL-LED board
3
two screws
(BVTP 2.6 (3CR))
5
connector
(CN701)
4
9
LEFT board
6
two screws
(BVTP 2.6 (3CR))
6
three screws
(BVTP 2.6 (3CR))
5
RIGHT board
4
connector
(CN741)
8
connector
(CN731)
3
7
1
Undo the lead pin.
FRONT board
2
two screws
(BVTP 2.6 (3CR))
2
four screws
(BVTP 2.6 (3CR))
– Inner view –
:LUHVHWWLQJ
lead pin
Click on the first or last page to see other HCD-PZ1D / MHC-PZ1D service manuals if exist.