Sony CDP-CE500 Service Manual ▷ View online
CDP-CE500
9
2-7. TABLE BLOCK
1 two screws
(BTTP M2.6)
4 Insert a tapering driver into the aperture
of the gear (loading A), and turn it in the
direction of the arrow A.
gear (loading A)
A
3 screw
(BTTP M2.6)
9 wire (flat type)
(6 core) (CN15)
0 table block
6 screw
(BTTP M2.6)
7 bracket (guide)
2 bracket (guide)
8
5
1 Match the position of the ditch of the
swing gear and marking.
2 Match the position of the hole of the
tray block and swing collar.
swing collar
hole of the
table block
table block
3UHFDXWLRQGXULQJWDEOHEORFNLQVWDOODWLRQ
marking
ditch of the swing gear
Note: When tray is pushed into interiors
most, the hole is seen.
CDP-CE500
10
2-8. TRAY
2-9. CHUCKING (DA11) PULLEY ASSY
1 floating screw
(PTPWH M2.6)
guide line
tray
table block
2 tray
– bottom view –
– rear side view –
Note: Please install the tray referring to the figure below.
Note: Please install the tray referring to the figure below.
3UHFDXWLRQGXULQJtrayLQVWDOODWLRQ
1 Rotate the chucking pulley (B) in the
direction of arrow.
2 chucking pulley (B)
5 chucking (DA11)
pulley assy
chucking (DA11) pulley assy
4 magnet assy
magnet assy
F mark
dot mark
3
Note: When you install the magnet assy
on the chucking (DA11) pulley assy,
please confirm F mark and the dot
mark are seen.
– Bottom view –
CDP-CE500
11
2-10. ROTARY MOTOR ASSY (M11), SENSOR BOARD
3
1 belt (rotary)
belt (rotary)
90º
90º
2 two screws
(BTTP M2.6)
2 two screws
(BTTP M2.6)
4 wire (flat type)
(6 core) (CN10)
1
2
5 Remove two solders.
6 rotary motor assy
(M11)
7 SENSOR board
rotary motor assy (M11)
rotary motor assy (M11)
gear (RM-B)
gear (RM-B)
Note: Any twist of the belt (rotary) is not allowed.
The belt (rotary) and the gear (RM-B) should
be free from grease and dusts.
– Side view –
– Side view –
%HQGSRVLWLRQRI6(1625ERDUG
CDP-CE500
12
2-11. GEAR (RV), GEAR (U/D), SWING GEAR
1 floating screw
(PTPWH M2.6)
3 floating screw
(PTPWH M2.6)
8 floating screw
(PTPWH M2.6)
qs floating screw
(PTPWH M2.6)
9 stopper washer (FR)
4 cam shaft
2 gear (RV)
gear (RV)
7 gear (loading C)
0 gear (loading B)
qd swing gear
swing gear
5 gear (U/D)
6 swing collar
gear (U/D)
hole
hole
qa
Note: Please make the hole of swing gear and hole of gear
(U/D) a sign, and match the position of biggest gap
of gear (RV) in two places.
biggest gap
biggest gap
3UHFDXWLRQGXULQJVZLQJJHDUJHDU8'
DQGJHDU59LQVWDOODWLRQ
DQGJHDU59LQVWDOODWLRQ
front side
rear side
1 Match the position of the ditch of the
rotary encoder and marking.
2 Match the position of the ditch
of the swing gear and marking.
3UHFDXWLRQGXULQJURWDU\HQFRGHULQVWDOODWLRQ
marking
ditch of the rotary encoder
ditch of the swing gear
marking
Click on the first or last page to see other CDP-CE500 service manuals if exist.