Sony CDP-CE500 Service Manual ▷ View online
CDP-CE500
5
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-2. CASE
(Page 5)
SET
2-3. FRONT PANEL BLOCK
(Page 6)
2-5. MAIN BOARD
(Page 8)
2-14. BASE UNIT BLOCK
(Page 14)
2-15. OPTICAL PICK-UP BLOCK
(DA11MMVGP)
(DA11MMVGP)
(Page 15)
2-15. BASE UNIT
(BU-DA11BD75)
(BU-DA11BD75)
(Page 15)
2-13. JUNCTION BOARD
(Page 14)
2-7. TABLE BLOCK
(Page 9)
2-6. USB-AUDIO BOARD
(Page 8)
2-8. TRAY
(Page 10)
2-9. CHUCKING (DA11) PULLEY ASSY
(Page 10)
2-10. ROTARY MOTOR ASSY (M11),
SENSOR BOARD
(Page 11)
2-12. LOADING MOTOR
ASSY (M10),
LOADING MOTOR
BOARD
(Page 13)
2-11. GEAR (RV),
GEAR (U/D),
SWING GEAR
(Page 12)
2-4. CD MECHANISM DECK
(CDM59-DA11)
(CDM59-DA11)
(Page 7)
Note: Follow the disassembly procedure in the numerical order given.
2-2. CASE
1 two screws
(case 3 TP2)
1 two screws
(case 3 TP2)
4 reflection prevention
sheet
reflection prevention sheet
125 mm
40 mm
2 two screws
(BVTP3
u 8)
5 case
case
3
3
– inner view –
Reflection prevention sheet pasted position
CDP-CE500
6
2-3. FRONT PANEL BLOCK
1 Insert a tapering driver into the hole
of the chassis bottom, and turn it in
the direction of the arrow A.
3 four claws
4 panel (loading 5CDUSB)
9 front panel block
5 wire (flat type) (13 core)
(CN300)
7 connector (CN850)
A
– Bottom view –
2
8 four screws
(BVTP3
u 8)
9 claw
9 claw
6 Lift up two lead pins.
Note: Make sure lead pin touch with
wire (flat type) (13 core).
front side
terminal face
:iUe VettiQJ
CDP-CE500
7
2-4. CD MECHANISM DECK (CDM59-DA11)
3 two screws
(BVTP3
u 8)
3 three screws
(BVTP3
u 8)
1 wire (flat type)
(25 core)
(CN902)
7 wire (flat type) (25 core)
(CN403)
2 connector
(CN301)
3 three screws
(BVTP3
u 8)
5 screws
(BVTP3
u 8)
4 Rotate the tray.
8 CD mechanism deck
(CDM59-DA11)
CD mechanism deck
(CDM59-DA11)
(CDM59-DA11)
MAIN board
6
Note: When you install the CD mechanism
deck (CDM59-DA11), please match
the position of the boss two places.
MAIN board
JUNCTION board
front side
:LUHVHWWLQJ
:LUHVHWWLQJ
front side
rear side
10mm or less
CDP-CE500
8
2-5. MAIN BOARD
9 Remove eight solders.
9 Remove five solders.
qa power transformer
(T102)
qs MAIN board
7 four PC board holders
6 shield (5CD) plate
1 Lift up three lead pins.
1 Lift up the lead pin.
2
8
3 wire (flat type)
(27 core)
(CN302)
4 power cord
connector
(CN101)
(CN101)
5 screw
(BVTP3
u 8)
5 screw
(BVTP3
u 8)
0 two S tight screw
(PTTWH3
u 6)
5 screw
(BVTP3
u 8)
Note: Please arrange the wire along the dotted
line on the MAIN board.
:LUHVHWWLQJ
front side
rear side
2-6. USB-AUDIO BOARD
5 two PC board holders
6 USB-AUDIO board
1 Lift up the lead pin.
2 wire (flat type) (27 core)
(CN901)
3 connector
(CN903)
4 two screws
(BVTP3
u 8)
:LUHVHWWLQJ
front side
rear side
Click on the first or last page to see other CDP-CE500 service manuals if exist.