DOWNLOAD Sharp LC-60UD20KN (serv.man5) Service Manual ↓ Size: 9.11 MB | Pages: 89 in PDF or view online for FREE

Selects the tone difference of the brightness and 
darkness of the image according to the type of 
programme watched from a maximum of + 3 to a 
minimum of - 3.

Automatically detects a film-based source (originally 
encoded at 24 or 25 frames per second, depending 
on the vertical frequency), analyses it and then 
recreates each still film frame for high-definition 
picture quality.

Adjusts effect to reduce judder 
from film contents. You can select 
a desired level of judder reduction 
to "High".

Adjusts effect to reduce judder 
from film contents. You can select 
a desired level of judder reduction 
to "Low".

Plays back images with equal 
display time for each frame, 
reproducing movie theatre 
experience.

Normal viewing mode.

Automatically adjusts the contrast of an image 
according to the scene (“On”, “Off”).

•  "Active contrast" is not available in case of 4K input.

“DNR” produces a clearer image (“Auto”, “High”, 
“Middle”, “Low”, “Off”).

•  This function may not be available depending on the 

input signal type.

The brightness level range of the OPC sensor’s 
automatic adjustments can be set according to 
your preferences. The adjustment range of the OPC 
sensor can be set to a maximum of 

e16 and a 

minimum of 

f16.

•  This function is available only when the “OPC” setting is 

set to “On” or “On:Display”.

•  The maximum setting cannot be set to a smaller number 

than the minimum setting.

•  The minimum setting cannot be set to a bigger number 

than the maximum setting.

•  The maximum and minimum settings cannot be set to 

the same number.

•  Depending on the brightness of the surrounding light, 

the OPC sensor might not operate if the adjustment 
range is small.

Go to “TV Menu” > “Setup” > “Audio”.

Setup

Bass

Adaptive volume

Audio

Treble

[Off]

STANDARD

CH list

:Back

:Enter

Menu

Balance

L30

R30

Adjust volume level automatically to lessen sudden 
volume change.

Adjust the volume gaps.

Does not adjust the volume gaps.

You can adjust the sound quality to your preference 
with the following settings.

c (Cursor)

d (Cursor)

For weaker treble

For stronger treble

For weaker bass

For stronger bass

Decrease audio 
from the right 
speaker

Decrease audio 
from the left 
speaker

This function produces a surround effect from the 
speakers.

Reproduces a life-like experience for 
events such as live sports or concert 
performances that take place in a stadium 
like setting.

Reproduces a concert hall experience with 
realistic live surround sound based on 
reverberant sounds measured in a concert 
hall.

Reproduces a movie theatre experience 
with realistic live surround sound based on 
reverberant sounds measured in a movie 
theatre.

Creates three-dimensional surround sound 
with detailed control of the signal phase.

Provides limited surround sound.

Outputs normal sound.

This function improves the sound quality by extending 
the selected range.

All Range: The low range will be extended and the 

sounds in the medium and high ranges, which have 
been lost due to the data being compressed, will 
be restored. This setting is effective when playing 
back audio through a wireless interface such as 
when using Bluetooth playback.

Low Range: The low range will be extended.
Off: No adjustment.

This function emphasises speech against background 
noise for greater clarity.

This function allows you to enable output of audio 
description if the TV receives a signal including audio 
description.

• When the “Audio description” is set to “On”, the audio 

description sound is superimposed on the main audio 
when you select a broadcast compatible with audio 
description.

• If you do not clearly hear the sound for the visually 

impaired, go to “TV Menu” > “Setup” > “Audio” > “Audio 
description setting” > “Mix level”, and select the upper 
level to turn up the volume.

• This function is available only for DTV broadcasts. This 

“Audio description setting” menu is not displayed for the 
ATV or the external inputs.

• The audio description sound is superimposed on the 

main audio only when the sound is output on the speaker 
sound output, headphone sound output and sound for 
audio out output. The sound is not output on the S/PDIF 
sound output and the SCART sound output.

• This function is not available for the AQUOS Audio 

speaker system.

• This function does not work during USB-recording 

playback.

Go to “TV Menu” > “Setup” > “ECO”.

Setup

No signal off

ECO picture control

ECO

Energy save

CH list

:Back

:Enter

Menu

No operation off

[Disable]

[Disable]

[Off]

[On]

This function automatically detects the image 
source and decreases the power consumption while 
keeping the brightness of the image unchanged.

•  This function does not work when “AV mode” is set to 

“DYNAMIC (Fixed)”, “DYNAMIC” or “MOVIE THX”.

•  This function does not work when “Energy save” is set 

to “Standard” or “Advanced”.

•  This function is greyed out in 3D mode.

This function enables you to reduce the backlight 
brightness in order to decrease the power 
consumption and increase the backlight life span as 
shown in the following table.

Reduces the backlight brightness.

Reduces the backlight brightness more 
than “Standard”.

The backlight brightness is the same 
value of your settings in the selected 
“AV mode”.

•  This function does not work when “AV mode” is set to 

“DYNAMIC (Fixed)” or “MOVIE THX”.

E

“Energy save” is set to “Standard”.

“Energy save” is set to “Advanced”.

When “Energy save” is set to “Standard” or 
“Advanced”, “Energy save” status icons appear 
in the “Picture” menu and channel information 
windows.

When set to “Enable”, the TV will automatically 
enter standby mode if there is no signal input for 15 
minutes.

•  Even if a TV programme finishes, this function may not 

operate because of interference from other TV stations 
or other signals.

The TV will automatically enter standby mode if no 
operations are performed in three hours if “Enable” 
is selected.

•  Five minutes before the TV enters standby mode, the 

remaining time displays every minute.

Allows you to set a time when the TV automatically 
enters standby mode. You can set the time span for 
entering standby mode after selecting “Change”.

•  Select “Off” to cancel the sleep timer.
•  When the time has been set, countdown automatically 

starts.

•  Five minutes before the preset of time expires, the 

remaining time displays each minute.

Go to “TV Menu” > “Setup” > “View setting”.

Setup

Network setup

Auto installation

View setting

Channel settings

CH list

:Back

:Enter

Menu

Bluetooth setup

The TV automatically detects and stores all available 
services in your area. This function also allows you 
to perform the channel setting for digital, satellite 
and analogue individually and reconfigure the 
settings after the initial auto installation has been 
completed.

 

Go to “TV Menu” > “Setup” > “View setting” > 
“Auto installation”.

 

Press 

c/d to select “Yes”, and then press ;.

 

Press 

a/b/c/d to select the desired 

language, and then press 

;.

•  PIN input is required when executing “Auto installation”. 

The default PIN is “1234”. To change the PIN setting, 
refer to Individual setting — PIN (Page 41). To reset the 
PIN setting (PIN input will no longer be needed), refer to 
Reset the PIN (Page 76).

•  You cannot set the Home/Store setting and the country 

setting in “Auto installation” in the “Setup” menu. If 
you want to reconfigure those settings, automatically 
execute initial auto installation after executing “Reset” 
from the “Setup” menu.

•  The current country setting is displayed on the screen.

 

Press 

a/b to select the broadcast standard 

you want to search, and then press 

;.

E

After selecting the service you want to search, 
either “Terrestrial” or “Cable”, refer to Digital 
broadcast setting on page 13.

E

The TV searches for, sorts and stores all the 
receivable TV stations. Refer to Analogue 
broadcast setting on page 13.

E

After selecting “Satellite search”, the current 
DVB-S/S2 setting screen is displayed. Refer to 
the “Satellite search” setting on page 14.

•  After selecting “Next” in the DVB-S/S2 setting screen, 

you need to select your preferred satellite broadcast to 
start searching.

You can reconfigure the DTV service settings 
automatically or manually.

 

Go to “TV Menu” > “Setup” > “View setting” > 
“Channel settings” > “Programme setup”.

 

Press 

a/b to select the broadcast standard 

you want to reconfigure, and then press 

;.

•  PIN input is required when executing “Programme 

setup”. The default PIN is “1234”. To change the PIN 
setting, refer to Individual setting — PIN (Page 41). 
To reset the PIN setting (PIN input will no longer be 
needed), refer to Reset the PIN (Page 76).

You can reconfigure the following settings when you 
select “Terrestrial” in the initial auto installation or 
the “Auto installation” menu.

E

Use this menu to add new services automatically 
after “Digital search” in the “Auto installation” menu 
has been completed.

E

Add new services within a specified frequency band.

•  Enter the frequency using 0

_9 numeric buttons.

•  You can perform “Manual search” with a service number 

only when the five Nordic countries have been selected 
in the country setting.

E

Configure various settings for each service using the 
colour (R/G/Y/B) buttons.

Service 

no.

Lock

Service 

name

Lock

CH skip

Old LCN

CH skip

Sort

Delete

 

Press 

a/b to select the desired service.

 

Press the colour button on the remote control 
unit corresponding with the item you want to 
reconfigure.

• The ✔ mark indicates the operation is set to on. 

Each time the colour button is pressed, you can 
switch the corresponding operation on/off.

•  Depending on the installation country and/or 

broadcaster or operator profile may only R option is 
available.